Page 1
Futon Bunk Bed
Assembly Instructions - Please keep for future reference
IMPORTANT NOTE:
The top surface of the mattress
should not come above this line.
758/4512
Dimensions
Width - 200cm
Depth - 99/174cm
Height - 165cm
Important
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
- Please read these instructions fully before starting assembly
Issue 1 - 06/11/13
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Because of the size of this unit,
it is recommended to assemble it
in the room intended for use.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Discard all extra fittings and
keep fittings out of reach of
children.
Warnings
• READ CAREFULLY - RETAIN
FOR FUTURE REFERENCE
• Regularly check and ensure
that all bolts and fittings are
tightened properly.
• Always use the ladder for
entering and leaving the upper
bunk.
• The recommended mattress
size is L1900 x W910 mm.
• Ensure thickness of mattress
does not exceed 220 mm.
• Refrain from using the bunk
bed if any structural part is
broken or missing.
• Assemble this product on a flat
surface.
• Assemble all parts loosely
before tightening any bolts.
• At least 2 people are required
to assemble this product.
• Unit weight: 54kgs.
• Retain Assembly Instructions
for future reference.
• Please advise your children to
only enter and leave the upper
bunk by using the ladder.
• Please prohibit more that one
person on the upper bunk.
• Please prohibit children from
jumping on the upper and lower
beds.
• WARNING: Do not allow
children under 6 years of age to
use the upper bunk due to risk
of injury and falls.
• STRANGULATION HAZARD -
Never attach or hang items such
as ropes, strings, cords,
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
harnesses and belts to any part
of the bunk bed.
• WARNING: Children can
become trapped between the
bed and the wall. To avoid risk
of serious injury the distance
between the top safety barrier
and the wall shall not exceed 75
mm or shall be more than 230
mm.
• Folding and unfolding the futon
should only be carried out under
adult supervision.
• THIS BED COMPLIES WITH
EN747-1:2012 / EN747-2:2012
Care and maintenance
• Please clean the unit surface
using either damp (not wet)
cloth and a mild domestic soap
solution or by using an
appropriate polish.
1
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this
unit.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Page 3
Components - Parts
Please check you have all the parts listed below
Sticker “3”Sticker “2”Sticker “1”
Back end post x 2
1 Front right-hand end post
(Ø5 x 165cm)
Sticker “4”
Lower left side rail
4
(89.5 x 24 x 2.5cm)
2
(Ø5 x 165cm)
Sticker “5”
5
Lower right side rail
(89.5 x 24 x 2.5cm)
3Front left-hand end post
(Ø5 x 165cm)
Upper side safety rail x 2
6
(91 x 36 x 4cm)
7
Upper back safety rail
(190.5 x 41.5 x 2.5cm)
Lower rail x 2
9 Left futon mechanism
(190.5 x 6.5 x 2.5cm)
10 Right futon mechanism
(43 x 17.5 x 5.5cm)
Upper front safety rail
8
(190.5 x 41.5 x 2.5cm)
Sticker “10” Sticker “11”
11
(43 x 17.5 x 5.5cm)
2
Page 4
Components - Parts (cont.)
Please check you have all the parts listed below
Sticker “13” Sticker “14”
12
Slats (with webbing attached) x 24
(94 x 1.6 x 2.5cm)
15
Ladder step x 4
(Ø2.5 x 29 cm)
16
Ladder brace
(76.5 x 1.5 x Ø1cm)
Left ladder side rail
13 Right ladder side rail
(150 x Ø2.5cm)
14
(150 x Ø2.5cm)
17
Futon clamp x 2
(13 x 4 x Ø0.5cm)
18
Back futon frame
(188 x 69.5 x 2.5cm)
19
Front futon frame
(188 x 69.5 x 6cm)
3
Page 5
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 08456 400800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
M8 x 60mm Bolt x 24
D
M8 x 40mm Bolt x 8
G H I
M6 x 35mm Bolt x 2 Screw x 2
J
M8 Curved washer x 32
M
Adhesive pad x 4
P Q
B
M6 x 80mm Bolt x 7
E
M8 x 30 mm Bolt x 4
K
M6 Curved washer x 15
N
Wall strap x 1
C
M6 x 50mm Bolt x 8
F
M6 x 20 mm Bolt x 10
M8 Lock nut x 24
L
Plastic washer x 8
O
Spring washer x 8
Allen key x 1
Spanner x 1
Tools required
Crosshead screwdriver
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
4
Page 6
Assembly Instructions
Step 1
Assembling end panels
Lay all parts flat on a soft
surface on the floor to
avoid damaging any of
the parts.
Note: Identify and
correctly position
the end posts ,
2 3
& by
1
looking for the
sticker labels
pasted on the
post.
a: Attach the lower right
side rail to back end
post and front
right-hand end post &
secure using washers
K
& , bolts & and
nuts as shown.
5
1
A
B
I
Note: Do not fully
tighten bolts at
this stage.
3
J
a: b:
Sticker “1”
B K
A
A J I
B
K
1
A
J
A
J
1
J
5
I
RIGHT-HAND END PANEL
F
F
6
5
F
Sticker “5”
F
1
6
Sticker “3”
F
3
BK
AJ
AJI
b: Attach the upper side
safety rail into position
& secure using bolts .
Repeat above steps to
assemble the left-hand
end panel using end
posts and , upper
side safety rail ,
lower left side rail as
shown in the diagram.
6
F
Note: Fully
tighten bolts all
bolts using allen
P
key .
1 2
6
4
Sticker “2”
2 1
B K
A J
A J I
LEFT-HAND END PANEL
F
6
F
4
Sticker “4”
F
F
Sticker “1”
BK
AJ
AJI
5
Page 7
Assembly Instructions
Step 2
Attaching rails
Note: Determine
your preferred
bunk bed entry
position. Then
attach the front
safety rail with
8
the entry space
positioned on the
left or right.
a: Identify the correct
rails for assembly and
with the help of an
assistant attach the lower
tubes of upper back
safety rail , upper front
safety rail and lower
rails to end posts
using bolts , washers
and nuts .
7
8
9
J A
I
Note: Do not fully
tighten bolts at
this stage.
b: Attach the top tubes
of upper back safety rail
7
and upper front safety
8
rail to end posts using
B K
bolts and washers .
Note: After all
bolts are
positioned, fully
tighten all bolts &
nuts using allen
P
key and
spanner .
Q
a: b:
J
A
J
A
K
B
J
A
J
A
1
J
A
J
A
B
A
I
A
I
A
A
7
I
1
K
7
J
I
J
2
9
J
I
J
8
9
I
I
Option for
right upper bunk entry
left upper bunk entry
B
B
K
A
J
A
J
1
A
J
A
J
Option for
K
I
I
7
1
A
J
A
J
3
A
J
A
J
6
Page 8
Assembly Instructions
Step 3
Attaching slats
a: With the help of an
assistant, line up the
12
slats onto upper rails
7 8
& . Push firmly
down to lock it into
position. Check that they
cannot be removed by
slightly pulling upwards.
b: Extend the end of the
webbing on the slats
and secure to bottom
edge of side safety rails
6
using screws .
Tighten screws using a
crosshead screwdriver.
12
H
6
H
6
7
12
8
H
Step 4
Assembling futon
mechanisms
Correctly position the left
10
& right futon
mechanisms and attach
to lower side rails &
using bolts and nuts .
Tighten bolts & nuts
using allen key and
spanner .
11
4
5
IE
P
Q
a: b:
4
10
I
I
E
E
12
8
H
5
E
11
I
I
I
E
11
I
12
6
5
E
E
7
Page 9
Assembly Instructions
Step 6
Step 5
Assembling front futon
frame
a: Position the front
17
19
10
11
D
I
J
Q
10
D
J
I
19
futon frame as shown
and secure it to futon
mechanisms &
with bolts , washers
and nuts . Tighten
bolts and nuts using allen
P
key and spanner .
b: Position the futon
clamps as shown and
carefully hook one end
on front futon frame .
D
17
17
D
J
I
19
11
D
J
J
I
I
Step 6
Assembling back futon
frame
a: Position the back
18
D
I
9
18 19
18
10 11
M
17
J
Q
futon frame and
carefully hook the other
end of futon clamps
as shown.
b: Fix the back futon
frame to futon
mechanisms &
with bolts , washers
and nuts . Tighten
bolts and nuts using allen
P
key and spanner .
c:
Remove backing from
adhesive pads and
carefully position at the
four corners between the
lower rails and futon
frames & .
a:
11
17
18
D
D
J
J
19
I
I
9
D
D
J
J
I
11
I
17
M
19
b:
c:
17
19
D
D
J
J
I
I
M
11
19
M
9
a:
18
M
D
D
J
J
I
I
10
9
M
b:
18
17
19
8
Page 10
Assembly Instructions
Step 7
Assembling ladder
Referring to diagram,
attach the ladder steps
to ladder side rails &
14
using bolts , spring
washers , curved
washers and plastic
washers . Tighten all
O
K
L
bolts using allen key .
13
C
P
Note: Identify and
correctly position
the ladder side
14
13
rails & by
looking for the
sticker labels
pasted on the
parts.
15
Sticker “13”
C
Sticker “14”
O
K
L
K
O
13
L
K
O
C
K
O
C
C
L
15
15
L
15
L
K
O
C
14
O
K
L
15
C
O
K
L
C
O
K
L
C
13
O
C
K
15
L
Step 8
Attaching ladder
Attach the ladder to the
upper front safety rail
using bolts as shown.
G
Tighten bolts using allen
P
key .
8
8
G
G
13
G
14
8
13
9
Page 11
Assembly Instructions
Step 9
Securing the ladder
Attach the ladder brace
16 14
to ladder side rail
& front right-hand post
using bolts . Tighten
F
bolts using allen key .
3
P
3
14
F
16
F
Step 10
Fixing to wall
This unit must be fixed to
a wall.
Move the bunk bed into
position on the wall.
Position the wall strap
to the top post of upper
back safety rail to
7
mark fixing holes on the
wall. Remove the wall
strap then drill holes and
insert appropriate wall
plugs. Reposition wall
N
strap & fix using
appropriate screws.
N
Wall
14
16
N
7
F
Warning:
Before drilling,
check wall for
hidden pipes and
cables. Consult a
qualified
specialist if
unsure.
Assembly is complete.
N
Wall
7
10
Page 12
Operation Instructions
Step 1
Folding the futon
a: Slightly pull up the
futon from the front edge.
b: Push it in to fold the
futon frame.
c: Then carefully put
down the futon as
shown.
Warning: Keep
hands away from
hinges, folding
mechanisms &
edges to prevent
possible
entarpment or
injury.
a: b:
c:
Risk of trapping
finger.
Step 2
Opening the futon
a: Slightly pull up the
futon from the front edge.
b: Pull it out to unfold
the futon frame.
c: Then carefully put
down the futon as
shown.
Warning: Keep
hands away from
hinges, folding
mechanisms &
edges to prevent
possible
entarpment or
injury.
a: b:
c:
Risk of trapping
finger.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
11
Loading...