Argos 4626930 ASSEMBLY INSTRUCTIONS

Page 1
Assembly Instructions - Please keep for future reference
Shelf section on the right
476/7978
462/6930
Shelf section on the left
Dimensions
Width - 100cm
Depth - 82cm
Height - 74cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020
MADE IN
BRITAIN
Issue 1 - 25/11/15
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 24kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
Care and maintenance
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
1
Page 3
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
Shelf Top (DF4610)
1
(64.9 x 32.7cm)
2 3
Shelf Base
(61.5 x 31.9cm)
Shelf Divider (DF4612)
5
(32.25 x 31.5cm)
(DF6423)
x 2
When applicable, remove any protective film before use
Shelf Panel (DF4611)
(61.5 x 31.9cm)
Shelf End
4
(69.1 x 32.3cm)
6
Desktop
(99.6 x 49cm)
(DF4613)
x 2
(DF4608)
End Panel (DF4609)
7 8
(70.6 x 35.4cm)
Back Panel (DF4614)
(70.6 x 33.8cm)
2
Page 4
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A B
Metal dowel (F901) x 22
D E F
Wooden dowel (F22) x 8
G H I
25mm Screw (F484) x 4
J
Foot (F854) x 1
Plastic Nail (F91) x 7
Plastic Insert (F502) x 4
Large locking
(F900) x 26
nut
C
Double metal dowel (F566) x 2
25mm Screw (F50) x 1
Allen Key (F36) x 1
Tools required
Eye protection
Rule Scissors Hammer
Cross-head screwdriver
(when using a hammer or drill)
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
3
Page 5
Assembly Instructions
Step 1
Prepare the shelf panel
Insert 4 large locking
B
nuts into the shelf panel .
Note: The arrows on the locking nuts must point towards the holes in the edge of the panels.
Tap 4 wooden dowels into the shelf panel .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
3
D
3
DO NOT USE the shelf base. It is similar to the shelf panel but, it has a shallow mark hole.
B
B
D
D
B
D
10mm
B
3
D
B
D
Step 2
Prepare the 2 shelf dividers
Insert 4 large locking
B
nuts into each of the 2 shelf dividers .
5
B
B
B
B
5
x 2
4
Page 6
Assembly Instructions
Step 3
Fit a divider to the shelf panel
a: Tap 2 double metal
dowels through the holes in the middle of the shelf panel and push a divider onto them until they ‘’bottom out’’.
b: Use a screwdriver to
tighten the 2 large locking nuts fitted to the divider .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
C
3
5
B
5
B
a:
C
C
3
5
b:
C
5
B
3
Step 4
Fit the other divider
Push the divider onto the shelf panel .
Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .
5
5
3
B
5
3
5
Page 7
Assembly Instructions
Step 5
Prepare the shelf base
a: Insert 4 large locking
nuts into the shelf
B
base .
Tap 4 wooden dowels into the shelf base .
Turn the shelf base over
b: Screw 2 metal
dowels into the shelf base .
Note: Tighten the metal dowels up fully against the panels.
2
D
2
A
2
D
D
Turn the
shelf base
over
B
B
B
2
A
A
B
D
D
A
Step 6
Fit the shelf base
Push the shelf base onto the divider .
Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .
B
5
2
5
5
2
6
Page 8
Assembly Instructions
Step 7
Prepare the 2 shelf ends
Screw 4 metal dowels into each of the 2 shelf ends .
Insert 2 large locking nuts into each of the 2 shelf ends .
4
B
4
A
Step 8
A
A
A
4
B
A
B
x 2
Fit a shelf end
Push a shelf end onto the assembly.
Use a screwdriver to tighten the 4 large locking nuts fitted to the shelf base and the shelf panel .
4
B
2
3
Step 9
Fit the other shelf end
Push a shelf end onto the assembly.
4
4
3
2
Use a screwdriver to tighten the 4 large locking nuts fitted to the shelf base and the shelf panel .
7
B
2
3
3
4
2
Page 9
Assembly Instructions
Step 10
Prepare the shelf top
Screw 6 metal dowels into the shelf top .
A
1
Step 11
Fit the shelf top
Push the shelf top onto the assembly.
1
A
A
A
A
A
A
1
1
4
5
Use a screwdriver to tighten the 6 large locking nuts fitted to the 2 shelf ends and the divider .
B
4
5
Step 12
Fit the foot and plastic nails
Screw the foot onto the shelf base using screw .
F
Tap 2 plastic nails into the bottom edge of each of the shelf ends .
Carefully stand the assembly up for the next step.
Warning: The unit is heavy. Lift with care.
J
2
E
4
4
4
E
J
E
F
2
E
E
4
8
Page 10
Assembly Instructions
Step 13
Prepare the end panel
Screw 2 metal dowels into the end panel .
A
7
Insert 2 large locking nuts into the end
B
panel .
7
Step 14
B
B
A
A
7
B
Prepare the back panel
Insert 4 large locking nuts into the back
B
panel .
8
Step 15
Fit the back panel to the end panel
B
B
B
8
Push the back panel onto the end panel .
Use a screwdriver to tighten the 2 large locking nuts fitted to the back panel .
B
8
9
8
7
8
7
Page 11
Assembly Instructions
Step 16
Prepare the desktop
Screw 4 metal dowels into the desktop .
Tap the 4 plastic inserts into the desktop .
A
6
H
6
IMPORTANT !
Only follow the 2 steps on this
page if you are going to have
the shelf section on the left.
If you are going to have the
shelf section on the right, follow
the 2 steps on the next page.
H
H
H
H
A
6
AA
A
Step 17
Fit the end panel and back panel assembly onto the desktop
Lower the end panel and back panel onto the desktop .
6
Use a screwdriver to tighten the 4 large locking nuts fitted to the end panel and back panel .
B
7
8
Tap 2 plastic nails into the bottom edge of the end panel and 1
7
into the back panel . .
7
8
E
8
E
E
8 7
6
E
10
Page 12
Assembly Instructions
Step 18
Prepare the desktop
Screw 4 metal dowels into the desktop .
Tap the 4 plastic inserts into the desktop .
A
6
H
6
IMPORTANT !
Only follow the 2 steps on this
page if you are going to have
the shelf section on the right.
If you are going to have the shelf
section on the left, follow the 2
steps on the previous page.
A
A
A
A
H
6
H
H
H
Step 19
Fit the end panel and back panel assembly onto the desktop
Lower the end panel and back panel onto the desktop .
6
Use a screwdriver to tighten the 4 large locking nuts fitted to the end panel and back panel .
B
7
8
Tap 2 plastic nails into the bottom edge of the end panel and 1
7
into the back panel . .
7
8
E
8
E
E
E
8
7
6
11
Page 13
Assembly Instructions
Step 20
Fit the desktop to the shelf top
Lower the desktop down onto the shelf top . .
1
Using screws , screw up through the shelf top . and into the plastic
1
inserts in the desktop .
Tighten up the screws with the allen key .
6
G
1
G
I
IMPORTANT !
Only follow this step if you are going to
have the shelf section on the left.
If you are going to have the shelf section
on the right, follow the next step.
6
1
G
I
G
G
G
12
Page 14
Assembly Instructions
Step 21
Fit the desktop to the shelf top
Lower the desktop down onto the shelf top . .
1
Using screws , screw up through the shelf top . and into the plastic
1
inserts in the desktop .
Tighten up the screws with the allen key .
6
G
1
G
I
IMPORTANT !
Only follow this step if you are going to
have the shelf section on the right.
If you are going to have the shelf section
on the left, follow the previous step.
6
G
I
G
G
G
1
13
Page 15
Assembly Instructions
Step 22
Assembly is complete
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020
14
Page 16
ALR3275
Loading...