Page 1
HYGENA PAIR OF RETRO CHAIRS
Assembly Instructions - Please keep for future reference
462/5670
Dimensions
Width - 43.3cm
Depth - 47.5cm
Height - 79.8cm
Important – Please read these instructions fully before starting assembly
need help or have damaged or missing parts, call the Customer Helpline:0345 6400800
If you
Issue 1 - 07/10/13
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed
on the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
•
Make sure you have enough
space to layout the parts before
starting.
• Parts of the assembly will be
easier with 2 people.
•
Care and maintenance
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Do not stand on the chair.
• Do not use this chair as step
ladder.
• To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Maximun safe weight of user:
110kgs.
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• From time to time check that
there are no loose screws on
this unit.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Page 3
If you have damaged or missing components,
Components - Panels
call the Customer Helpline: 0345 6400800
Please check you have all the panels listed below
The quantities below are for 2 chairs
Chair frame x 2
1
(75.6 x 57.5cm)
underside
4
Seat pad x 2
(42.2x39.8cm)
Chair frame x 2
2
(75.6 x 57.5cm)
Backrest x 2
3
(39.6 x 14.5cm)
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly of 2 chairs. In some cas es
more fittings may be supplied than are required.
A
68mm Bolt x 8 50mm Screw x 2
D
Plain washer x 8
B
E
Hex key x 1
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
105
C
26mm Bolt x 8
110 115 120 125 130 135 140 145 150 155 160 165 170
2
Page 4
Assembly Instructions
Step 1
Attaching chair frame
Attach chair frame
to chair frame as
shown in the figure.
2
1
2
1
Step 2
Assemble seat pad
Place seat pad
upside down on a clean,
Carefully position the
chair frame on the seat
pad and secure using
A
bolts and plain washers
.
D
Note: Do not fully
tighten bolts.
4
A
D
4
3
Page 5
Assembly Instructions
Step 3
Assemble backrest
3
Parts of the assembly will
be easier with 2 people.
Assemble backrest to
3
the chair frame using
screw
Note
C
tighten the screws.
:
C
C
C
C
Step 4
Fixing chair frames
upside down chair on a
clean surface,
frame and using
screw
21
B
Re-thighten all the bolts.
Turn the chair upright.
Assembly is complete.
secure chair
22
21
22
B
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400800
Loading...