Page 1
GV 2 Door 1 Drawer Sideboard
Assembly Instructions
-
Please keep for future reference
461/3369
464/6989
464/3724
Dimensions
Width - 80cm
Depth - 35.5cm
Height - 74cm
Important
-
-
Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Version 1 Date: 13/10/15
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fi ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Handy Hints
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your fl oor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Pilot holes for
guidance only
Argos = 0345 6400800
Left panel
1
Top panel
4
Battom panel
5
(34.9 x 72.4cm)
(80.1 x 35cm)
(76.8 x 32.3cm)
Right panel
2
(34.9 x 72.4cm)
10
11
12
Finished front edge
Back panel
3
Drawer front panel
Drawer back panel
Pilot holes for
guidance only
(79.4 x 66.5cm)
(76.1 x 16.1cm)
(71.9 x 11.8cm)
Drawer bottom panel
(74.3 x 28.6cm)
Shelf panel
6
Middle panel
7
Front panel
8
Pilot holes for
guidance only
Door panel x 2
9
(76.8 x 30cm)
(76.8 x 11cm)
(76.8 x 7cm)
(48.1 x 37.9cm)
Drawer left panel
13
Finished front edge
Drawer right panel
14
Drawer support
15
(29 x 10.1cm)
(29 x 10.1cm)
(27.7 x 6cm)
2
Page 4
Components - Fittings
Please check you have all the fi ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fi ttings
may be supplied than are required.
A B C
(This screw is included in
the runners bag)
(This screw is included in
the door hinges bag)
12mm Screw x 12
D
30mm Screw x 6
G
E F
18mm Screw x 4
H
(This screw is included in
the handles bag)
15mm Locking nut x 1039mm Locking pin x 15
J K L
M N O
Left inside runner x 1Left outside runner x 1
P Q R
Shelf support x 4Nail x 16 Support cover x 4
14mm Screw x 615mm Screw x 16
30mm Dowel x 6
I
12mm Locking nut x 5
Right inside runner x 1Right outside runner x 1Door hinge x 4
Plastic support x 3
S T
Door pad x 4Handle x 2
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Drill
7mm Suitable drill bit
(for use with wall plug)
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
The screws length is measured from the head to the point (30mm screw shown).
3
Page 5
Assembly Instructions
Step 1
Attaching runners and
hinges
a:
Position the Left out-
side runners in from
K
front edge of the Left side
panel .
Use Screws to fix the
Left outside runners
2
A
K
onto the Left side panel
.
2
a:
2 Holes upside
2
A
A A
A
A
A
K
K
K
Pilot holes for
runner position
2
2
b:
Position the Right out-
side runners in from
M
front edge of the Right
side panel .
Use Screws to fix the
Right outside runners
1
A
M
onto the Right side panel
.
1
b:
2 Holes upside
A
A
A A A
M
A
M
Pilot holes for
runner position
1
1
M
1
Continued on next page.
4
Page 6
Assembly Instructions
Step 1 - continued
c:
Use Screws to fix
the Door hinges ‘back
B
J
plates’ onto the Left side
panel .
Insert Dowels into the
Left side panel .
Screw Locking pins
2
F
2
G
into the Left side panel
2
.
Note:
Insert locking pins
as far as shown.
Do not over tighten.
c:
G
G
B
F
J
G
2
B
G
J
B
J
d:
Use Screws to fix
the Door hinges ‘back
B
J
plates’ onto the Right side
panel .
Insert Dowels into the
Right side panel .
1
F
1
Screw Locking pins
G
into the Right side panel
1
.
Note:
Insert locking pins
as far as shown.
Do not over tighten.
d:
G
F
B
J
G
B
G
J
B
1
J
G
5
Page 7
Assembly Instructions
Step 2
Attaching bottom panel
a:
Use Screws to fix
Plastic supports onto
the Front panel .
b:
Use Screws to fix
Front panel onto the
Bottom panel .
Insert Dowels into the
Bottom panel .
C
O
8
C
8
5
F
5
a:
b:
C
C
O
C
8
O
C
O
C
C
C
8
O
F
c:
Insert Dowels into
Middle panel .
7
C
O
F
F
c:
O
5
F
7
Continued on next page.
F
6
Page 8
Assembly Instructions
Step - continued 2
b:
Carefully locate the
Left panel onto the
Middle panel and
Bottom panel .
Insert 3 Locking nuts
into the Middle panel
and Bottom panel .
1
7
5
H
7
5
Use a screwdriver to turn
Locking nuts clockwise
H
to lock.
d:
H
1
H
7
5
H
H
e:
Carefully locate the
Right panel onto the
2
unit.
Insert 3 Locking nuts
H
into the unit.
Use a screwdriver to turn
Locking nuts clockwise
H
to lock.
e:
H
7
5
H
H
2
H
7
Page 9
Assembly Instructions
Step 3
Attaching top panel
a:
Screw Locking pins
into the Top panel .
4
Note:
Insert locking pins
as far as shown.
Do not over tighten.
a:
G
G
G
G
G
4
G
b:
Carefully locate the
Top panel onto the
4
unit.
Insert 4 Locking nuts
H
into the unit.
Use a screwdriver to turn
Locking nuts clockwise
H
to lock.
b:
Unfinished
back edge
H
H
4
H
H
H
2
1
8
Page 10
Assembly Instructions
Step 4
Fixing back panel
Attach Back panel
using nails .
P
Important:
The unit MUST
be ‘square’ when
back is attached.
P
Unfinished back surface
3
3
Step 5
Drawer assembly
a:
Screw Locking pins
into the Drawer front panel
10
.
Note:
Insert locking pins
as far as shown.
Do not over tighten.
Continued on next page.
G
a:
G
G
G
G
G
G
10
9
Page 11
Assembly Instructions
Step 5 - continued
b:
Fix Drawer right panel
14
, Drawer support
and Drawer left panel
15
13
on to Drawer front panel
10
.
Insert 5 Locking nuts
I
into the Drawer right panel
14 15
, Drawer support
and Drawer left panel .
13
Use a screwdriver to turn
Locking nuts clockwise
H
to lock.
b:
14
I
13
15
I
10
I
I
c:
Carefully slide the
Drawer bottom panel
into the grooves.
12
c:
I
I
Unfinished back surface
12
15
Continued on next page.
14
10
10
Page 12
Assembly Instructions
Step 5 - continued
d:
Position the Drawer
back panel onto the
unit using Screws .
11
D
d:
D
D
D
11
12
15
D
D
14
e:
Turn the unit upside
down carefully.
Use Screws to fix the
Left inside runners and
Right inside runners
A
N
L
onto the unit.
e:
A
N
A
L
A
A
8
12
10
A
A
11
Page 13
Assembly Instructions
Step 6
Inserting drawers
With help, carefully stand
unit upright.
Warning:
The unit is heavy.
Lift with care.
Slide the assembled
drawers fully onto runners.
Step 7
Attaching shelf panel
a: Slide Support covers
R
onto Shelf supports .
Insert Shelf supports
(Support covers are
included) into the unit.
Ensure they are well fitted
before inserting the
Shelves.
Set the shelf
Note:
R
supports to the desired
height.
b:
Slide Shelf panel
into the unit.
Q
Q
6
a:
b:
R Q
+
R Q
+
R Q
6
Finished
front edge
12
Page 14
Assembly Instructions
Step 8
Attaching door hinges
and handles
Fix 4 Door hinges to
Door panel using
Screws .
B
Attach Handle using
Screws .
E
J
9
S
Tear off the protective
backing from the Door
Pads .
T
Carefully stick the Door
T
pads onto the Door
panel .
9
Step 9
Hanging doors
B
B
B
J
J
J
E
9
T
E
S
T
T
X 2
a:
With help, slot Door
hinges onto ‘hinge
J
plates’.
b:
Tighten screw shown
to lock hinges in position.
Repeat
a
and b for
opposite door.
Hinge adjustment
See ‘
’
in step 10 if the doors
need adjusting.
J
J
J
13
a:
J
b:
Page 15
Assembly Instructions
Step 10
Hinge adjustment
a:
To move doors up or
down: loosen screws
shown and move doors to
suit.
Once doors are aligned,
re-tighten Screws .
b:
To move doors in or
out: loosen screw shown
and move doors to suit.
Re-tighten screws.
B
a:
Door
b:
B
c:
To move doors left or
right: loosen screw shown
and move doors to suit.
Re-tighten screws.
Door
c:
Door
14
Page 16
Assembly Instructions
Step 11
Finishing the unit
It would be useful
Note:
to ask someone to help
you at this stage.
With help, place the unit
in the intended position.
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
15
Loading...