Page 1
COMPACT BUTTERFLR DINING SET
Assembly Instructions - Please keep for future reference
457/1607
Dimension
Fully Extended
Width - 92cm Width - 37.5cm
Length - 120cm
Height - 75cm Height - 74cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Help line: 0345 6400800
Chair
Depth - 48cm
Issue 2 - 26/11/13
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fi ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Parts of the assembly will be
easier with 2 people.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your fl oor.
• To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Do not stand on the chair.
• Do not use this chair as a step
ladder.
• Maximun safe weight of user
on the chair: 110kgs.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• From time to time check that
there are no loose screws on
this unit.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Page 3
If you have damaged or missing components,
Components - Panels
call the Customer Helpline: 0345 6400800
Please check you have all the panels listed below
Supporting bar x 2
1
(87 x 2 cm)
Side frame x 2
4
(67.5 x 43 cm)
Middle table top
7
(92 x 40 cm)
Supporting bar x 2
2
(87 x 2 cm)
Front panel
5
(67.5 x 34 cm)
Side table top x 2
8
(92 x 40 cm)
3
Bottom board
(80 x 30 cm)
6
Back panel
(73 x 34 cm)
Folding chairs x 4
9
(75.4 x 37.5 cm)
2
Page 4
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
12mm Bolt x 36 14mm Bolt x 4
D
22mm Bolt x 2
G
Spring washer x 12
J
Hinge x 6
M
Castor with lock x 2
B
E
34mm Bolt x 4
H
Small plain washer x 12
K
Hex key x 1
N
Castor x 2
C
20mm stopper x 2
F
42mm Bolt x 8
I
Plain washer x 4
L
Wrench x 1
O
Handle x 2
Tools required
Phillips screwdriver
(Medium)
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
3
Page 5
Assembly Instructions
Step 1
a: Assemble handle
O
Fix handle
panel
5
b: Assemble castor
Screw castor into
front panel
to front
using bolt D.
M
25
O
D
Step 2
Step 2
Assemble handle
Fix handle to back
panel
O
6
using bolt
M
M
D
26
O
D
4
Page 6
Assembly Instructions
Step 3
Fix supporting bar
2
to the bottom board
using
.
bolts
B
3
22
Step 4
B
23
22
B
22
23
Assemble castor
N
Screw castor
side frame
into
4
.
24
24
N
N
5
Page 7
Assembly Instructions
Step 5
Assemble the frame unit
Attach front and back
panels using bolts
spring washer
plain washer
Note: Do not fully
tighten bolts.
H
G
F
5
25
26
23
H
G
F
Step 6
Assemble the frame unit
position side frame
a:
onto the supporting bar
using plain washer
I
b:
Attach front and back
panels and side frame onto
supporting bar using
bolts
spring washer
F
small plain washer
21
H
Note: Please fully
tighten the bolts.
21
24
4
2
21
F
G
H
26
24
G
25
23
22
I
6
Page 8
Assembly Instructions
Step 7
Assemble table top
Two people are
needed here.
Place the table tops
upside down, fix side
table tops
table top
and hinges
Screw stoppers
the side table tops.
8
onto middle
7
using bolts
J
C
into
A
28
27
28
A
A
A
A
J
C
Step 8
Finishing the unit
Two people are
needed here.
Attach supporting bar
to middle table top using
E
bolts
,spring washer
plain washer
7
H
Note: Re-tighten all the
bolts.
Turn the table upright.
E
1
G
21
27
G
H
7
Page 9
Assembly Instructions
Step 9
Additional information
a: Depending on your
requirement open one
or both of the side table
top and ensure the side
frame is locked.
Step 9
b: To move the table, lift
up the end opposite to
the castors position as
shown in the figure.
8
Page 10
Assembly Instructions
Step 9
c: To save space, the
chairs can be put
inside the table as shown.
9
Step 10
Remark:
For chairs use
please ensure supporting
bar
plastic cap
b
is secured with
a
9
a
b
9
Loading...