Page 1
Triple Bunk Bed
Important - Please read these instructions fully before starting assembly
Dimensions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 28/05/13
758/5432
Assembly Instructions - Please keep for future reference
758/5425
758/5449
Length - 200cm
Width - 142.5cm
Height - 170cm
Page 2
Important - Please read these instructions fully before starting assembly
Mattress height safety notice
Important
1) Please note the maximum mattress height is indicated on the corner post inside the opening at the
top of the ladder.
2) This is legal requirement and it is vital that the mattress does not exceed this mark.
3) Maximum thickness of the mattress is 20cm:The top of the mattress shall not come above the line
marked on the bed.
4) All assembly fixings should always be tightened properly.Take care to ensure that no fixings are
loose.
5) Recommended size of the mattress for the top bunk is 90×190cm.For the lower bed is 135×190cm.
6) The bunk bed should not be used if any structural part is broken or missing.
7) Warning: High beds and the upper bed of bunk beds are not suitable for children under six years
due to the risk of injury from falls.
8) Children can strangle in items such as ropes, strings, cords, harnesses and belts attached to or
hung on a bunk bed.
Warning
1) Children can become trapped between the bed and wall. To avoid risk of serious injury the distance
between the top safety barrier and the wall shall not exceed 75mm or shall be more than 230mm.
2) The bed complies with EN747-1:2012
1
Safety and Care Advice
!
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Place the product on flat and
steady surface during use.
• Keep these instructions for
future use.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
during initial assembly. Only
upon completion of the
assembly should all fixing
points be fully tightened.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Dispose of all packaging
carefully and responsibly.
Care and maintenance
• Safety: To avoid any risk of
suffocation to animals or
children dispose of the plastic
bags immediately.
• Cleaning: As with all surfaces
clean with a damp cloth and
mild detergent, do not use
bleach or abrasive products.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Page 3
Please check you have all the parts listed below
Components - Parts
2
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
1
Rear post x 2
(4.5 x 170cm)
2
Front post x 2 (4.5 x 170cm)
3
Ladder frame x 2 (2.2 x 109cm)
4
End panel x 2 (97 x 39.8cm)
16
Lower stretcher x 2 (3 x 133.7cm)
5
Front guard (191 x 42cm)
6
Rear guard (191 x 42cm)
7
Lower side rail (rear) (191 x 7.3cm)
8
10
Top bunk slats x 22 (□2 x 1 x 95cm)
11
Lower bed slats (with hole) x 3(1.6 x140cm)
12
Lower bed slats x 14 (1.6 x 140cm)
13
Central support (1.9 x 191cm)
14
Legs x 3 (1.9 x 23.5cm)
15
Ladder rungs x 5 (1.9 x 30.5cm)
Lower side rail (front) (191 x 7.3cm)
Extra brackets
9
Top bunk slats x 2 (□2 x 1 x 95cm)
Page 4
Please check you have all the fittings listed below
Components - Fittings
3
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note:
The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B C
M6x15mm Allen screw x 8
D E
M6x45mm Allen screw x 21
F
Arc washer-large x 16
G H
J
Nut x 12
L M
N
Plastic plug x 2
A
Arc washer-small x 19
Plastic washer x 16
M6x65mm Allen screw x 7
M8x65mm Allen screw x 8
M6x10mm Allen screw x 82
K
Plastic cap x 4
M6x35mm Allen screw x 4
P
Small allen key x 2
Q
Large allen key x 1
Plastic spacer x 10
0
5
10 15 20 25 30 35 40
45
50
55
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150
1 2
3
4
5 6
Ruler/tape
measure
Ruler - Use this ruler to help correctly identify the screws
Tools required
Page 5
1
B
A
C
D
2
2
4
16
16
2
C
4
Note: Hole at top
Back
Front
Top
Bottom
C
B
D
C
A
Assembly Instructions
4
Step 1
Assembling side
frames
Lay rear post , front
post , end panel
and lower stretcher
flat on the floor as shown.
Note:
The holes in end
panel must be at the
top.
Insert end panel into
the large holes in rear
post and front post
.
Secure using fixings
and .
Note:
Do not fully
tighten screws .
Secure lower stretcher
in between the posts
using fixings and .
Note:
Do not fully
tighten screws .
Insert end caps into
the top of the front and
rear posts.
Repeat for the other side
frame.
1
2
4
16
4
4
1
2
A
C
A
16
B
C
B
D
Page 6
6
7
1
1
1
G
F
H
E
J
7
1
B
C
H
E
F
G
6
J
Extra brackets
B
C
H
E
J
G
F
Back
Front
E
F
E
E
F
F
Assembly Instructions
5
a:
b:
Assembling rear guard
Two people are needed
here.
With help, stand both
side frames upright.
a: Assemble rear guard
in between the side
frames as shown.
Note:
Do not fully tighten
any screws
during the assembly.
Secure at the top using
fixings and as
shown.
Secure at the bottom
using fixings ,
and as shown.
Note:
Plastic washers
are located in between
the rear guard and the
side frames.
Step 2
b: Assemble lower side
rail at the back of the
side frames using fixings
, and as
shown.
Note:
Side rail has
extra brackets on the top
edge.
Note:
Ensure all screws
have been left loose
before proceding to the
next step.
6
B C
E F G H
J
F
7
E F G H
J
7
Page 7
5
8
Note: Hole
Note: Hole
E
H
F
G
H
E
J
B
C
J
F
G
2
2
B
C
J
E
H
F
G
F
E
E
F
E
F
2
8
5
Assembly Instructions
6
a:
b:
Assembling front
guard
At this stage, choose if
you want the ladder on
the right hand side or left
hand side.
a: According to which
side you want the ladder,
assemble front guard
in between the side
frames using fixings ,
and as shown.
b: Assemble lower side
rail (front) in between
the side frames using
fixings , and .
Note:
Ensure the ladder
fixing holes in the front of
side rail are on the
same side as the ladder
access gap in front guard
.
Note:
Ensure all fixings
are left loose.
Step 3
5
E F
G H
J
8
E F G H
J
8
5
Alternative assembly
Page 8
K
10
5
K
10
9
9
K
K
K
5
Assembly Instructions
7
Step 4
Slats at
each end
9
4
Arrow label to
point outside
9
10
9
K
Assembling top bunk
slats
Fit slats in the very
last fixing holes at each
end of the top bunk.Use
fixing screws to
secure.
Note:
Slats have
been labelled for easier
identification.
Note:
To ensure slats
are fitted the right way
around, the arrow labels
must point outwards
as shown.
Fit slats to the
remaining fixing holes in
the top bunk. Use
screws to secure
9
K
9
9
10
K
Page 9
12
K
12
8
K
K
8
G
K
11
11
11
13
14
14
14
G
14
13
11
G
G
K
K
K
K
K
8
Assembly Instructions
8
Step 6
Step 5
Assembling lower bed
slats
Assemble lower bed
slats to the frame
using screws .
12
K
Assembling lower bed
support frame
Assemble lower bed
slats to the frame in
the positions shown.
Use screws to secure.
Note:
Slats have an
extra hole in the middle.
With help, assemble
central support and
legs underneath slats
as shown.
Use screws to secure.
11
K
11
13
14
11
G
11 11 11
8
Location of slats .
11
Page 10
3
3
C
M
THIS END UP
C
M
3
C
M
J
5
8
J
N
N
2
5
N
2
15
L
G
G
L
G
L
15
3
3
3
THIS END UP
Assembly Instructions
9
Step 8
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Home Retail Group. 489-499 Avebury Boulevard. Saxon Gate West. Central Milton Keynes. MK9 2NW
Assembly is complete.
Step 7
Assembling ladder
Assemble ladder rungs
and plastic spacers
in between ladder
frames using screws
.
Note:
Do not fully
tighten screws .
15
L
3
G
G
Attaching ladder
Assemble the ladder to
the frame using fixings
and .
Fixings are located
inside the frame as
shown.
Note:
The top of the
ladder has been labelled.
Important:
Once all parts
have been
assembled together, go
round and ensure all
fixings are fully tightened.
Plastic caps can be
used to cover the
un-used holes in front
post 2 as shown.
C
J
M
J
!
2
N
Loading...