Argos 4266376 ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020

Important - Please read these instructions fully before starting assembly

Dimensions

Width - 70.3cm

Depth - 51.6cm

Height - 182.3cm

Sparkle - 2 Door Robe

Assembly Instructions - Please keep for future reference

Issue 3 - 02/10/15

417/8385

414/1343

413/3052

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 46kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.

• Dispose of all packaging carefully and responsibly.

Rule

Tools required

Rule

ScissorsSquare

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Step ladder

Electric drill (only use when drilling into walls)

Components - Panels

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020

Please check you have all the panels listed below

When applicable, remove any protective film before use

2

1

2 4

7

Left Side (DF3837)

(180.8 x 49.4cm)

Rail (DF3840)

(66.9 x 8cm) x 2

Horizontal (DF3841)

(66.9 x 49.2cm) x 2

Right Side (DF3838)

(180.8 x 49.4cm)

3

Top (DF3839)

(70.3 x 51.6cm)

Door (DF3842)

(172.4 x 34.5cm) x 2

Back (X1738-695)

(173.8 x 69.5cm)

5

8

Hanging Rail (FHR663)

(66.3cm long)

6

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Components - Fittings

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020

3

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A B

D E F

G H

C

J K

Large locking nut (F900) x 16

Metal dowel (F901) x 16 Wooden dowel (F22) x 16

L

Rail Holder (F891) x 2

13mm Screw (F63) x 20

Hinge plate (F523) x 8

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Nail (F51) x 30

Plastic Nail (F91) x 4

Hinge (F522) x 8

I

25mm Screw (F50) x 6

Handle (F569) x 2

Important: Always pair up the hinges with the hinge plates from the same bag. DO NOT mix them up.

*** ***

Finished

front edge

Finished

front edge

C

Assembly Instructions

4

Prepare the left side

a: Screw 6 metal

dowels into the left side .

Note: Tighten the metal dowels up fully against the panels.

Insert 2 large locking nuts into the left side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Tap 2 wooden dowels into the left side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

b: To fit the rail holder

screw through the top hole with screw and into the mark hole drilled in the left side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Fit 4 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

A

1

C

1

Step 1

A

F

D

F

D

F

D

10mm

C

A

B

J

B

D

F

1

F

J

1

b:

a:

Prepare the 2 horizontals

Insert 4 large locking nuts into each of the horizontals .

Tap 4 wooden dowels into each of the horizontals .

A

C

Assembly Instructions

5

Step 2

A

C

B

J

F

D

Finished

front edge

Finished

front edge

Prepare the right side

a: Screw 6 metal

dowels into the right side .

Insert 2 large locking nuts into the right side .

Tap 2 wooden dowels into the right side .

b: To fit the rail holder

screw through the top hole with screw and into the mark hole drilled in the right side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Fit 4 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

A

2

C

2

B

4

C

4

B

D

F

2

F

J

2

b:

a:

B

A

Step 3

x 2

4

Finished

front edge

A

Assembly Instructions

6

Step 4

A

B

Fit the 2 horizontals to the right side

Push the 2 horizontals onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to each horizontal .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

2

4

B

4

2

4

Prepare the 2 rails

Insert 2 large locking nuts into each of the rails .

Tap 2 wooden dowels into each of the rails .

5

C

5

B

Step 5

x 2

Finished

front edge

B

A

5

Assembly Instructions

7

Step 6

Step 7

2

Fit the 2 rails

Push the 2 rails onto the right side .

Use a screwdriver to tighten the large locking nut fitted to each rail . .

2

5

B

5

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the 6 large locking nuts fitted to the horizontals and the rails .

1

B

5

4

5

4

1

Note: Support this rail until the left side has been fitted in the next step.

4

Finished

front edge

Assembly Instructions

8

Step 8

Step 9

Prepare the top

Screw 6 metal dowels into the top .

A

3

A

Finished

front edge

3

Fit the top

Note: To make it easier to fit the top and base panels, place polystyrene blocks from the packaging underneath the side panels to raise the assembly.

Push the top onto the assembly.

Use a screwdriver to tighten the 2 large locking nuts fitted to each side and .

3

B

1 2

1

2

Polystyrene

block

Polystyrene

block

yy

xx

Assembly Instructions

9

Step 10

b:

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the outside edges of the back .

Note: Nails should be spaced about 150mm apart.

Stand the unit up for the next step.

8

G

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

8

xx

G

8

Step 11

Fit the 4 plastic nails

Tap 2 plastic nails into the bottom edge of each of the sides and . .

Carefully stand the unit up for the next step.

H

1

2

H

1

2

Warning: The unit is heavy. Lift with care.

Assembly Instructions

10

Step 12

6

D

Fit the hanging rail

Push the hanging rail into the rail holders fitted to the side panels.

6

D

Step 13

Prepare the 2 doors

Push fit 4 hinges into each of the 2 doors .

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.

F

K

7

90

K

x 2

K

F

K

F

K

F

K

F

7

Assembly Instructions

11

Step 14

Fit doors and handles

Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges.

a: Push the hinge

onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.

b: Keep the hinge

FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.

c: The hinge must be

flat against the hinge plate prior to any adjustment.

d: The hinge must

NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.

e: Attach a handle to

each door using 3 screws .

K

J

K

J

I

E

7

a: b:

c: d:

J

K

J

B

J

K

A

K

J

B

e:

E

I

E

7

I