Page 1
Single HD Covered Clothes Rail White/Black
Assembly lnstructions - Please keep for future reference 425/6238
424/2541
Dimensions
Width - 90cm
Depth - 50cm
Height - 160cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts,call the Customer helpline
: 0345 6400800
Issue 1-04/22/15
Page 2
!
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2.
• Remove all fittings from the
plastic bags and separate them into
their groups.
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting
• Do not stand or put over
weight on the parts this
could cause damage.
Care and maintenance
• Assemble the unit as close to its
final position (in the same room)
as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
floor.
• Parts of the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Warning
the wall for hidden pipes and
cables.
• Dispose of all packaging carefully
and responsibly.
• Warning
Hanging rail 15 kg
Shelf 15 kg
: Before drilling,check
: Max loading weight
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on this
unit.
• This product should not be
discarded with household waste.
take to your local authority waste
disposal centre.
1
Page 3
Components - Parts
Please check you have all the parts listed below
If you need help or have damaged or missing
parts, call the Cust omer helpline: 0345 6400800
1 Thin rods x 2pcs(80cm)
4 Thin rods x 2pcs(85cm) 5 Thin rods with screw
6 Support bar x 1pcs(91cm)
10 screw thread x 2pcs
2 Thin rods with screw
thread x 2pcs(80cm)
thread x 2pcs(80cm)
7 Hanging rail x 1pcs(91cm)
Components - Fittings
3 Shelf x 2pcs(90x50cm)
8 Cover x 1pcs
9 Plastic holder x 20pcs
Please check you have all the parts listed below
Note: The quantities below are correct amount to complete the assembly.
In some cases more fittings may be supplied than required
A B
Screw x 1 Wall plug (for solid walls only)x1
Tools required
MEASURE
Tape Measure
2
Page 4
Assembly Instructions
Step 1
Note: It would be useful
to ask someone to help
you at this stage.
a: Attach thin rod 1 and
2 to connector 9 .
b: Attach shelf 3 to thin
rod 1 and 2 .
Then turn it over.
a:
b:
1
1
2
9
3
1
1
2
2
2
c: Attach thin rods 4
and 5 as shown.
3
c:
4
4
5
1
10
1
2
3
5
10
2
Page 5
Assembly Instructions
Step 2
a: Attach suport bar 6
to hin rods 4 .
b: Attach shelf 3 and
the plastic holder 9
to thin rods 5 as
shown
a:
b:
6
4
4
9
3
c: Attach hanging rail
7 to the shelf 3 as
shown.
9
7
c:
4
Page 6
Assembly Instructions
Step 4
a: Fitting the cover
into the assembled
frame as shown in the
figure.
Note: It is
recommended that two
people fit the cover to
the frame.
8
a:
8
b: Fasten the ties at
bottom.
5
b:
Page 7
Assembly Instructions
Step 5
Fixing to wall
It is recommended that
the wardrobe is fixed to
a wall.
Note:
The correct type of fixing
must be used for your
wall,seek professional
advice if doubt.
Mark the fixing hole on
the wall and remove the
wardrobe. Drill a hole and
insert a wall plug .
Warning:
!
Before drilling,
check the wall for
hidden pipes and
cables.
B
A
Top panel
B
wall
Reposition the wardrobe
and fix the wall strap
using screw .
The assembly is now
complete.
A
If you need help or have damaged or missing parts,call the Customer helpline: 0345 6400800
6
Page 8
7
Loading...