Chester - Solid Pine Desk
Assembly Instructions- Please keep for future reference
389/6400
418/8124
Dimensions
Width - 120cm
Depth - 50cm
Height - 74,3cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call t h e C u stomer Helpline: 03456 400 800.
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
We do not
recommend the
use of power
drill/drivers
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
for
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Components - Panels
Please check you have all the panels listed below
1 2
Top panel
3
Division
7
Large back rail x2 (67,1 x 8,5cm)
10
Middle front frame
(37,3 x 4,7cm)
(120 x 50cm)
(72,5 x 45,8cm)
4
Left side panel
8
Small back rail
(42,5 x 4,7cm)
11
Bottom front frame
(37,3 x 8,6cm)
Right side panel
(72,5 x 45,8cm)
(72,5 x 46,9cm)
5
Right front frame
(72,5 x 4,6cm)
6
Left front frame
(72,5 x 4,6cm)
9
Top front frame
(37,3 x 4,7cm)
12
Drawer front x2
(36,8 x 26,6cm)
13
Drawer right side x2
(35 x 20 cm)
16
Drawer bottom x2
(34,7 x 34,3cm)
14
Drawer left side x2
(35 x 20cm)
17
Side drawer runner x4
(34.4 x 3,7cm)
15
Drawer back x2
(33,3 x 20cm)
18
Back panel (68,3 x 44,3cm)
2
Components - Fittings
If you have damaged or missing components,
call the Customer Helpline: 03456 400 800.
Please check you have all the fittings listed below
Note:
The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B C
Wooden dowel x 57
30mm Screw x 52
Drawer
handle x 2
D
Nail x 20
G
16mm Screw x 12
E
22mm Bolt x 4
F
Bracket x 6
Tools required
Phillips screwdriver
(medium & large)
Small
hammer
Ruler - Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
3
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
m
2
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Assembly Instructions
Step 1
Insert dowels into the
A
indicated parts.
A
(4x)
17
A
A
(2x)
13
A
(2x)
A
14
A
A
11
A
4
7
A
8
(2x)
3
A
A
A
A
A
A
A
2
A
09
10
A
A
A
A
A
A
Step 2
Fixing runners.
Attach side drawer runners
17
to division using
screws .
B
Attach side drawer runners
to left side panel
17
using screws .
Attach brackets through
pre drilled holes on left
side panel and division
3
using screws
where shown.
3
4
B
F
4
G
B
B
B
B
B
B
17
G
F
B
B
B
17
4
17
F
B
G
(3x)
B
B
17
3
(3x)
4
Assembly Instructions
Step 3
Fixing left front frame
to the left side panel
(Two people required for
an easier assembly)
Insert left front frame
a:
6
into left side panel
4
through joints.
.
(3x)
6
Yes!No!
4
G
Note:
Before fixing brakets
F
into place it is important
to ensure that the slot
and groove of parts
6
and are fully pushed
4
together and lined up
correctly at top and bottom.
Fix brakets into front
frame using screws .
G
Step 4
Fixing right front frame
to division.
(Two people required for
an easier assembly).
a:
Insert right front
frame into division
3
5
through joints.
(+)
(-)
6
(-)
4
op
T
(3x)
Yes!No!
5
3
Note:
Before fixing brakets
F
into place it is important
to ensure that the slot
and groove of parts
5
and are fully pushed
3
together and lined up
correctly at top and bottom.
Fix brakets into front
frame using screws . G
5
T
G
op
5
(+)
3
Assembly Instructions
.
Step 5
Attach small back rail ,
top front frame and
9
bottom front frame to
left side panel using
screws .
B
4
Fit middle front frame
to left front frame .
Make sure panels are
correctly positioned as
shown in the diagram.
8
11
10
6
Attention:
11
B
10
8
B
4
9
B
Step 6
Fixing the division
Two people are required
for an easier assembly.
Fit division to the
assembled part, then fix it
using screws .
3
B
3
B
B
6
Assembly Instructions
Step 7
Fixing top panel
Two people are required
for an easier assembly.
Caution:
Carefully lay the top panel
on a soft and clean surface
to avoid damaging the
product.
Attach assembled frame
to the top panel using
screws .
B
1
Note correct
position of parts as shown.
B
B
B
B
3
1
Step 8
Fixing back rail.
Fit large back rails
the right side panel
then fix them using
screws .
B
7
to
2
7
7
B
2
B
7
Assembly Instructions
Step 9
Two people are required
for an easier assembly.
Fit back panels to
division and right side
panel to top panel
3
4
7
1
as shown. Then, fix the
parts using screws .
B
B
7
3
4
B
1
7
Step 10
Fixing back panel.
Important:
MUST
Desk be
square when back panel
is attached.
Attach the back panel
18
using nails .
D
18
D
8
Assembly Instructions
Step 11
Drawer assembly.
a:
b:
c:
a:Attachdrawer sides
13
front
b:
slide drawer bottom
into slots on drawer sides
c:
attach drawer back
using screws .
d:Using screw attach
the drawer handle to
the drawer front.
Repeat step 11 to the
other drawer.
14
and to the drawer
12
usingscrews .
15
B
E
C
16
Step 12
Insert drawers into unit.
B
B
13
B
14
B
12
16
15
B
(2X)
E
d:
E
C
With the back of the
drawers past the front
frames, use a hammer to
tap dowels in flush to
drawer sides.
This is a safety catch to
stop drawer falling out.
A
A
A
A
Assembly is complete.
A
If you need help or have damaged or missing parts, call t h e A rgos Customer Helpline: 03456 400 800
or Homebase Customer Helpline: 0345 077 8888.
9
A
Loading...