Chloe Nest of Tables
Assembly Instructions
-
Please keep for future reference
609/1439
609/1893
609/6300
415/9672
Dimensions
Large / Small
Width - 56/40cm
Depth - 40/30cm
Height - 47/35.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Version 3 Date: 19/03/15
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fi ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your fl oor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
1
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Argos = 0345 6400800
Pilot holes for
guidance only
Large support x 2 (43.8 x 6cm)
3
Pilot holes for guidance only
Large table top (56 x 40cm)
1
Pilot holes for
guidance only
Medium support x 4 (27.8 x 6cm)
4
Pilot holes for
guidance only
Small support x 2 (17.8 x 6cm)
5
Large leg x 4 (45.5 x 4.5cm)
6
Pilot holes for
guidance only
Small table top (40 x 30cm)
2
Small leg x 4 (34 x 4.5cm)
7
2
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
A
40mm Dowel x 24
D
15mm Locking nut x 16
B
C
43mm Locking pin x 16 14mm Screw x 20
E
Plastic support x 10
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Drill
7mm Suitable drill bit
(for use with wall plug)
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
110 115 120 125 130 135 140 145 150 155 160 165 170
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
3
Assembly Instructions
Step 1
Fitting the large legs
Insert Dowels into
a:
the Large legs .
Screw Locking pins into
the Large legs .
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
Note: It would be useful
to ask
you at this stage.
someone to help
A
6
B
6
a:
b:
B
A
B
6
A
B
X 4
D
b
D
6
3
to
b:
onto the Large support
Use a screwdriver to turn
Locking nuts clockwise
to lock.
Note: The screw holes
on the legs and support
should align.
Note:
assembly the other legs.
Locking nuts
Large legs
D
Follow the same
.
6
D
3
D
6
X 2
Continued on next page.
4
Assembly Instructions
Step 1 - continued
c:
Locking nuts
Large legs
the Medium supports .
D
6
4
Use a screwdriver to turn
Locking nuts clockwise
D
to lock.
Note: The screw holes
on the medium supports
should face inward.
c:
D
6
6
6
3
D
D
D
4
D
6
Step 2
Fitting the large table
top
a:
Insert Dowels fully
into the Large legs
A
.
6
a:
4
A
A
6
6
3
A
A
6
Continued on next page.
5
6
Assembly Instructions
Step 2 - continued
Carefully locate the
b:
Large table top onto
the unit.
1
b:
1
c:
Plastic supports onto
the Large table top .
C
E
1
c:
C
E
C
E
C
1
C
6
Assembly Instructions
Step 3
Finishing the large
table
Carefully turn the table
upright.
Step 4
Fitting the small legs
Insert Dowels into
a:
the Small legs .
Screw Locking pins into
the Small legs .
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
A
7
B
7
a:
B
A
B
7
B
A
X 4
Continued on next page.
7
Assembly Instructions
Step
Note: It would be useful
to ask
you at this stage.
b:
onto the Small support
Use a screwdriver to turn
Locking nuts clockwise
to lock.
Note: The screw holes
on the legs and support
should align.
Note:
assembly the other legs.
4 - continued
someone to help
Locking nuts
Small legs
D
Follow the same
b
D
7
5
to
b:
.
D
7
D
5
D
7
c:
the Medium supports .
Use a screwdriver to turn
Locking nuts clockwise
to lock.
Note: The screw holes
on the medium supports
should face inward.
Locking nuts
Small legs
D
D
7
4
c:
X 2
7
D
7
7
5
4
7
D
D
4
5
8
Assembly Instructions
Step
Step
Fitting the small table
top
a:
into the Small legs
5
Insert Dowels fully
A
.
7
a:
A
A
A
A
7
7
Carefully locate the
b:
Small table top onto
the unit.
2
7
b:
2
Continued on next page.
9
Assembly Instructions
Step
c:
Plastic supports onto
the Small table top .
5 - continued
C
E
2
C
c:
E
C
C
E
2
C
Step 6
Finishing the Small
table
Carefully turn the table
upright.
10
Assembly Instructions
Step 7
Finishing the unit
With help, place the unit in
the intended position.
Large table
Small table
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
11
Loading...