osaka
abingdon
23465758
4149905
dimensions
width: 40,0 cm
width; 48,2 cm
depth: 40,0 cm
depth: 43,0 cm
height 59,6 cm
height; 55,5 cm
assembly instructions - please keep for future reference
if you need help or have damaged or missing parts, call the argos customer helpline: 03456 400 800
350811-01
issue 1 - 02-06-2015
safety and care advice
!
important - please read these instructions fully before starting assembly
• assembly should be carried
out by a competent adult
only.
• check you have all the
components and tools listed
on pages 2 and 3.
• do not use this product if
any components are missing
or damaged.
• remove all fittings from the
plastic bags and separate
them into their groups.
• keep children and animals
away from the work area,
small parts could choke if
swallowed.
care and maintenance
• only clean using a damp
cloth and mild detergent, do
no use bleach or abrasive
cleaners.
• make sure you have enough
space to layout the parts
before starting.
• do not stand or put weight
on the product, this could
cause damage.
• assemble the item as close
to its final position (in the
same room) as possible.
• assemble on a soft level
surface to avoid damaging
the unit or your floor.
• parts of the assembly will
be easier with 2 people.
• regularly check fastenings
to ensure they are tightened.
• we do not recommend the
use of power drill/drivers
i
nserting screws
damage the unit. Only use
hand screwdrivers.
• dispose of all packaging
carefully and responsibly
• made for home retail group,
milton keynes.
• this product should not be
discarded with household
waste.
take to your local authority
waste disposal centre.
, as this could
for
.
note: if required the next
page can be cut out and
used as reference
throughout the assembly.
keep this page with these
instructions for future
reference.
1
if you have damaged or missing components, call
components - panels
the argos customer helpline: 03456 400 800
please check you have all the panels listed below
top
1
(47,1 cm x 43 cm)
side, left
2
(47,7 cm x 38 cm)
6
back rail
(38,2 cm x 7 cm)
9
drawer front
(37,6 cm x 20,9 cm)
3
side, right
(47,7 cm x 38 cm)
7
front rail
(38,2 cm x 9,2 cm)
x
2
4
post, left
(54 cm x 5 cm)
x
2
back
8
(44,9 cm x 40,5 cm)
5
post, right
(54 cm x 5 cm)
x
2
10
drawer side, left
(38 cm x 18,2 cm)
350811-03
x
drawer back
11
drawer side, right
(38 cm x 18,2 cm)
x
12
(33,3 cm x 18,2 cm)
2
x
2
2
drawer bottom
13
(34,3 cm x 37,7 cm)
x
2
2
components - ttings
please check you have all the panels listed below
note: the quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
Aa
ø7.8 x 40mm wooden dowel x
Ca
ø15 x 10.5mm cam x
Fh
wall strap and instruction x 1
Kb
ø5.8 x 8mm screw x
CL
350mm drawer runner, left, side x
DL
14
12
14
ø3.5 x 35mm screw xBa12
Cb
ø5 x 8, cc34mm bolt x
Fi
back fitting w. ø3.5 x 15mm screw x
m4 x 20mm screw xHd2
Ko
ø4,2 x 9,5mm screw x
CR
2
350mm drawer runner, right, side x
DR
14
ø3 x 12mm screw xBo8
1.2 x 15mm nail xDi25
Gm
4
54mm handle x
ø4 x 25mm screw xJb8
Vl
8
44 x 23 x 23mm angle x
2
2
2
350mm drawer runner, left x
350mm drawer runner, right x
2
2
tools required
phillips screwdriver
(medium & large)
flatblade screwdriver
(medium)
hammer
ruler - use this ruler to help correctly identify the screws
17060 16040 90 15013070 120100 14011050 803020100
3
350811-04
assembly instructions
step 1
assembly of the chest.
1
4
step 1.1
screw the bolts Cb into
the holes indicated on the
1
top
.
step 1.2
x the posts 4 and 5
2
onto the sides
using screws
holes indicated.
the top of the posts
5
and
and
and the sides 2
3
must be ush.
and 3
Jb
into the
4
Cb
Jb
8
3
2
5
6
4
Cb
Cb
1
Cb
Cb
ø5 x 8, cc34mm bolt x
7
4
5
ø4 x 25mm screw xJb8
Jb
Jb
4
Jb
Jb
2
Jb
Jb
Jb
4
5
3
step 1.3
knock the dowels Aa
into the holes indicated
on the sides
using a small hammer.
screw the bolts Cb into
the holes indicated on the
sides
350811-05
2
2 and 3
and 3.
5
Aa
ø7.8 x 40mm wooden dowel x
Cb
Cb
Cb
4
3
ø5 x 8, cc34mm bolt x
2
Aa
Aa
2
Aa
Aa
4
assembly instructions
step 1.4
x the drawer runners
CL
and CR to the sides
2
and 3 using screws
Kb
through the holes as
indicated.
See details.
CL
350mm drawer runner, left, side x
Kb
ø5.8 x 8mm screw x
Kb
Kb
CL
CL
Kb
Kb
12
2
Kb
CR
2
350mm drawer runner, right, side x
CR
Kb
Kb
3
CR
Kb
CR
Kb
Kb
2
Kb
step 1.5
x the angles Vl using
Ko
screws
into the holes
indicated on the front
7
rail
.
step 1.6
Kb
CL
Ko
ø4.2 x 9.5mm screw x
Ko
Vl
7
note the hole!
bottom end of
right hand side
4
Vl
44 x 23 x 23mm angle x
Ko
Ko
Vl
Aa
2
knock the dowels Aa
into the holes indicated
on the back rail
6
using a small hammer.
5
Aa
ø7.8 x 40mm wooden dowel x
Aa
2
6
350811-06
assembly instructions
step 1.7
place the sides 2 and
3
onto the back rail 6.
6
2/3
.
Ca
into the
, arrows
.
Ca
to the
2
push cams
holes indicated on the
back rail
pointing towards the
sides
turn the cams
right to x the sides
3
and
Ca
ø15 x 10.5mm cam x
3
2
2
6
Ca
Ca
step 1.8
place the top 1 onto
2
the sides
push cams
the holes indicated
on the sides
3
, arrows pointing
towards the top
turn the cams
right to x the top
and 3.
Ca
into
2
and
1
Ca
to the
.
1
Ca
ø15 x 10.5mm cam x
4
1
Ca
Ca
.
3
2
Ca
350811-07
6
assembly instructions
step 1.9
place the front rail
as shown.
x the angles
sides using screws
see detail.
Vl
to the
Ko
Ko
7
ø4.2 x 9.5mm screw x
.
7
Ko
4
7
Vl
step 1.10
place the back 8 into
the rabbet on the top
1
and onto the posts
4
and 5.
important!
make sure the
!
angle between
1
the top
4
and 5
the back
x the back
1
and the posts 4/5
and the back rail
nails
use a small hammer.
and the posts
is 90° when
8
is attached.
8
to the top
Di
.
6
using
Di
distribute equally !
1.2 x 15mm nail x
14
1
1
Di
Di
8
1
4
Di
6
5
7
350811-08
assembly instructions
step 1.11
important!
!
its recommended that
the chest of drawers is
xed to the wall.
Fh
use the ttings
follow the instructions
included with the
ttings.
.
step 2
assembly of the
drawers.
Fh
wall strap and instruction x 1
12
11
step 2.1
x the drawer sides 10
11
and
back
using screws
to the drawer
12
as shown,
Ba
.
step 2.2
knock the dowels Aa
into the holes indicated
on the drawer sides
11
and
hammer.
using a smal
10
10
13
9
x
2
ø3.5 x 35mm screw xBa12
Ba
12
Ba
11
10
x
2
Aa
ø7.8 x 40mm wooden dowel x
11
Aa
8
10
Aa
Aa
Aa
x
2
350811-09
8
assembly instructions
step 2.3
screw the bolts Cb into
the holes indicated on
9
the drawer front
.
step 2.4
slide the drawer bottom
13
into the drawer sides
10
and 11.
step 2.5
push the drawer front 9
onto the drawer sides
11.
and
place cams
Ca
into the
holes indicated, arrow
pointing towards the front.
turn the cams
Ca
right to x the front.
10
to the
Cb
Cb
Cb
Cb
Cb
9
ø5 x 8, cc34mm bolt x
x
2
8
11
10
x
13
2
Ca
ø15 x 10.5mm cam x
8
9
Ca
10
Ca
Ca
x
11
2
step 2.6
important!
make sure the
!
angle between
9
10
and
and
Fi
the drawer front
the drawer sides
11
is 90° before the drawer
13
bottom
is xed using Fi
as shown.
to adjust the angle between
the drawer sides and the
fronts push the tting
sidewards.
see details.
9
Fi
back fitting w. ø3.5 x 15mm screw x
4
90°
Fi
9
11
13
Fi
10
x
2
Fi
Fi
Fi
350811-10
assembly instructions
step 2.7
place the drawer runners
DL
and DR onto the drawer
10
sides
and 11 and push
them onto the back of the
9
front
x the drawer runners
and
10
.
DL
DR
to the drawer sides
and 11 using screws Bo
into the holes indicated.
step 2.8
DL
350mm drawer runner, left x
Bo
DL
Bo
Gm
DL
10
DR
350mm drawer runner, right x
2
2
ø3 x 12mm screw xBo8
Bo
DR
Bo
11
x
2
x the metal handles Gm
to the drawer fronts
using screws
Hd
9
.
step 2.9
slide the drawers onto
the runners and into the
chest.
54mm handle x
Gm
2
9
Hd
m4 x 20mm screw xHd2
x
2
if you need help or have damaged or missing parts, call the argos customer helpline: 03456 400 800
home retail group - 489-499 avebury boulevard - saxon gate west - central milton keynes mk9 2nw
350811-11
10
A Guide to
Wall Mounting & Fixings
IMPORTANT:
When drilling into walls always check that there are no
hidden wires or pipes etc. Make sure that the screws and
wall plugs being used are suitable for supporting your unit.
Consult a qualified tradesperson if you are unsure.
HINTS:
1) General Rule Always use a larger screw and wall plug if you are not sure.
2) Ensure you use the recommended drill bit to match the wall plug and hole size.
3) Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4) Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure the plug is fitting below the ceramic
tile to avoid splitting or cracking.
5) Ensure wall plugs are well fitted and are a tight fit in the drilled hole.
Types Of Walls
You can use one of the following types
of wall plug if your walls are made of
brick, breeze block, concrete, stone,
wood or plaster board.
No.1 "Standard" Wall Plug
General Wall Materials
These come in various sizes and are made
from plastic or sometimes wood fiber.
No.2 "General Purpose" Wall Plug
Aerated / Breeze Block
No.3 "Shield Anchor" Wall Plug
Heavy Loads
For use with heavier loads such as TV
& HiFi Speakers and Satellite Dishes etc.
No.4 "Cavity Fixing" Wall Plug
For use with plaster board partitions or
hollow wooden doors.
No.5 "Cavity Fixing - Heavy Duty"
Wall Plug
No.6 "Hammer Fixing" Wall Plug
For use with walls stuck with plaster
board. The hammer fixing allows it to
be fixed to the wall rather than the plaster
board. Always check the fixing is secure
to the retaining wall.
CARE & MAINTENANCE
SAFETY
Always check the fitting and
location to ensure your safety in
and around the home.
Generally aerated blocks should not be
used to support heavy loads, use a
specialist fitting in this case.
For light loads, a General Purpose Plug
can be used.
For use when fitting or supporting heavy
loads such as shelving, wall cabinets,
coat racks.
FITTING
From time to time check the fitting
to ensure the wall plugs or screws
do not become loose.
Loading...