osaka
abingdon
23465758
4134477
dimensions
width: 40,0 cm
width: 91.1 cm
depth: 40,0 cm
depth: 50.0 cm
height 59,6 cm
height: 189.9 cm
assembly instructions - please keep for future reference
if you need help or have damaged or missing parts, call the argos customer helpline: 03456 400 800
350808-01
issue 1 - 08-06-2015
safety and care advice
!
important - please read these instructions fully before starting assembly
• assembly should be carried
out by a competent adult
only.
• check you have all the
components and tools listed
on pages 2 and 3.
• do not use this product if
any components are missing
or damaged.
• remove all fittings from the
plastic bags and separate
them into their groups.
• keep children and animals
away from the work area,
small parts could choke if
swallowed.
care and maintenance
• only clean using a damp
cloth and mild detergent, do
no use bleach or abrasive
cleaners.
• make sure you have enough
space to layout the parts
before starting.
• do not stand or put weight
on the product, this could
cause damage.
• assemble the item as close
to its final position (in the
same room) as possible.
• assemble on a soft level
surface to avoid damaging
the unit or your floor.
• parts of the assembly will
be easier with 2 people.
• regularly check fastenings
to ensure they are tightened.
• we do not recommend the
use of power drill/drivers
i
nserting screws
damage the unit. Only use
hand screwdrivers.
• dispose of all packaging
carefully and responsibly
• made for home retail group,
milton keynes.
• this product should not be
discarded with household
waste.
take to your local authority
waste disposal centre.
, as this could
for
.
note: if required the next
page can be cut out and
used as reference
throughout the assembly.
keep this page with these
instructions for future
reference.
1
if you have damaged or missing components, call
components - panels
the argos customer helpline: 03456 400 800
please check you have all the panels listed below
top
1
(90 cm x 50 cm)
4
bottom
(81,1 cm x 46,4 cm)
7
back rail
(81,1 cm x 7 cm)
8
front rail
(81,1 cm x 9,2 cm)
2
side, left
(182,1 cm x 45 cm)
10
13
hanging rail
(80,2 cm x 2,2 cm)
350808-03
back, small
(83,2 cm x 22,9 cm)
3
side, right
(182,1 cm x 45 cm)
16
drawerside, left
(45 cm x 18,2 cm)
5
post, left
(188,4 cm x 5,0 cm)
14
drawer front
(80,5 cm x 20,9 cm)
back
9
(156,5 cm x 41,5 cm)
6
post, right
(188,4 cm x 5,0 cm)
x
2
17
drawerside, right
(45 cm x 18,2 cm)
x
x
2
12
x
door
(155,3 cm x 40,1 cm)
2
2
11
h-profile
(154,5 cm x 1,7 cm)
15
drawer back
(76,2 cm x 18,2 cm)
18
drawer bottom
(77,1 cm x 44,7 cm)
2
components - ttings
please check you have all the panels listed below
note: the quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
Aa
ø7.8 x 40mm wooden dowel x
Ca
ø15 x 10.5mm cam x
Et
self adhesive bumper, ø10 x 3mm x
back fitting w. ø3.5 x 15mm screw xFi2
54mm handle xGm4
Kb
ø5.8 x 8mm screw x
Mc
18
6
18
ø3.5 x 35mm screw xBa6
Cb
ø5 x 8, cc34mm bolt x
Fc
4
back fitting - 14 x 19mm x
Fl
support for hanger rail - 15mm x
Hd
m4 x 20mm screw x
Ko
ø4,2 x 9,5mm screw x
Pm
4
18
ø3 x 12mm screw xBo22
1.2 x 15mm nail xDi50
Fh
4
2
8
wall strap and instruction x 1
ø4 x 25mm screw xJb20
Mf
ø26mm cup hinge x
Vl
6
0mm crossplate x
CL
450mm drawer runner, left, side x
DL
450mm drawer runner, left x
6
door stop x
CR
1
450mm drawer runner, right, side x
DR
1
450mm drawer runner, right x
4
44 x 23 x 23mm angle x
1
1
tools required
phillips screwdriver
(medium & large)
flatblade screwdriver
(medium)
ruler - use this ruler to help correctly identify the screws
2
hammer
17060 16040 90 15013070 120100 14011050 803020100
3
350808-04
assembly instructions
step 1
assembly of the
wardrobe.
1
11
9
9
3
2
13
5
4
6
10
6
7
5
8
step 1.1
x the posts 5 and 6
2
onto the sides
using screws
holes indicated.
the top of the posts
6
and
and
and the sides 2
3
must
be ush.
Jb
Jb
and 3
Jb
into the
5
Jb
Jb
ø4 x 25mm screw xJb20
Jb
Jb
Jb
Jb
Jb
Jb
5
Jb
2
Jb
5
3
Jb
Jb
Jb
Jb
Jb
Jb
6
Jb
Jb
350808-05
6
4
assembly instructions
step 1.2
knock the dowels Aa
into the holes indicated
on the sides
Cb
use a small
hammer.
screw the bolts Cb into
the holes indicated on the
sides
2
2 and 3.
Cb
Cb
Cb
Cb
Cb
and 3.
Cb
Cb
Aa
ø7.8 x 40mm wooden dowel x
Cb
6
ø5 x 8, cc34mm bolt x
8
2
Aa
Aa
3
Aa
Aa
step 1.3
x the crossplates Mc
to the sides
2
using the pre-mounted
screws.
position the crossplates
Mc
exactly as shown.
x the supports for
hangerrails
sides
screws
Fl
to the
2
and 3 using
Bo
.
and
3
Mc
ø3 x 12mm screw xBo2
Mc
Fl
support for hanger rail - 15mm x
2
Mc
0mm crossplate x
6
Mc
Bo
Fl
2
3
Mc
Mc
Mc
Fl
5
Bo
350808-06
assembly instructions
step 1.4
x the drawer runners
CL
and CR to the sides
2
and 3 using screws
Kb
through the holes as
indicated.
see details.
CL
450mm drawer runner, left, side x
Kb
ø5.8 x 8mm screw x
6
2
Kb
Kb
CL
CL
Kb
CR
1
450mm drawer runner, right, side x
3
Kb
Kb
CR
1
step 1.5
x the angles Vl using
Ko
screws
into the holes
indicated on the front
8
rail
.
step 1.6
knock the dowels Aa
into the holes indicated
on the back rail
using a small hammer.
7
CL
Ko
ø4.2 x 9.5mm screw x
Ko
Vl
note the hole!
bottom end of
right hand side
4
8
Kb
CR
Vl
44 x 23 x 23mm angle x
Ko
Ko
Vl
Aa
ø7.8 x 40mm wooden dowel x
Aa
2
2
350808-07
7
Aa
6
assembly instructions
step 1.7
screw the bolts Cb into
the holes indicated on the
1
top
knock the dowels Aa
into the holes indicated
on the bottom
a small hammer.
push the door stops
into the holes indicated
on the top
bottom
.
4
using
Pm
1
and the
4
.
Aa
ø7.8 x 40mm wooden dowel x
Cb
6
ø5 x 8, cc34mm bolt x
6
Pm
door stop x
Cb
Cb
4
Cb
1
Pm
Pm
Aa
4
Aa
Aa
Pm
Cb
Cb
Cb
Aa
Aa
Aa
Pm
step 1.8
place the sides 2 and
3
onto the
and the
push cams
holes indicated on the
bottom 4 and
7
rail
,
arrows
pointing
towards the
sides
2/3
bottom 4
back rail 7.
Ca
into the
the back
.
Ca
ø15 x 10.5mm cam x
8
3
Ca
Ca
4
2
Ca
Ca
Ca
turn the cams
Ca
right to x the sides
3
and
.
7
to the
2
Ca
7
Ca
Ca
350808-08
assembly instructions
step 1.9
place the top 1 onto
2
the sides
push
cams
Ca
into the
holes indicated
on the sides
3
, arrows pointing
towards the top
and 3.
2
and
1
.
Ca
Ca
ø15 x 10.5mm cam x
Ca
6
1
Ca
3
Ca
2
turn the cams
Ca
to the
right to x the top
step 1.10
place the front rail
as shown.
x the angles
sides using screws
see detail.
Vl
to the
Ko
.
1
Ko
8
ø4,2 x 9,5mm screw x
8
.
2
350808-09
3
Ko
8
8
assembly instructions
step 1.11
place the backs 9 into
the rabbet on the top
1
, into the h-prole
11
, onto the posts 5
6
and
bottom
and onto the
4
.
1
9
!
important!
make sure
the angle
between the
1
top
the posts
and
x the backs
the top
posts
nails
hammer.
and
5
6
is 90°
9
1
and the
5
and 6 using
Di
. use a small
to
Bo
ø3 x 12mm screw x
distribute equally !
9
Di
1
11
9
Di
4
1.2 x 15mm nail xDi43
Fc
back fitting - 14 x 19mm x
4
9
Di
Bo
Fc
Bo
Bo
Bo
Fc
5
Fc
Di
Fc
10
7
4
6
place the back 10 onto
5
the posts
the bottom
back rail
x
the back 10 to the
posts
5
the back rail
Di
nails
nally x the backs
10 to the bottom 4
and
using screws
the back ttings
and 6,
4
and the
7
.
and 6 and
7
using
.
Bo
through
Fc
9
.
9
350808-10
assembly instructions
step 1.12
important!
!
the wardrobe is
heavy. lift with care.
its recommended that
the wardrobe is xed to
the wall.
Fh
use the ttings
follow the instructions
included with the
ttings.
.
13
Fh
wall strap and instruction x 1
13
350808-11
10
assembly instructions
step 2
assembly of the
drawers.
15
17
step 2.1
x the drawer sides
17
and
back
using screws
to the drawer
15
as shown,
Ba
.
step 2.2
16
16
18
14
ø3.5 x 35mm screw xBa6
Ba
15
17
Ba
16
Aa
knock the dowels Aa
into the holes indicated
on the drawer sides
17
and
using a smal
16
hammer.
step 2.3
screw the bolts Cb into
the holes indicated on
14
the drawer front
.
ø7.8 x 40mm wooden dowel x
4
17
16
Aa
Aa
Aa
Aa
Cb
4
Cb
Cb
ø5 x 8, cc34mm bolt x
Cb
Cb
14
11
350808-12
assembly instructions
step 2.4
slide the drawer bottom
18
into the drawer sides
16
and 17.
16
17
18
step 2.5
push the drawer front 14
16
onto the drawer sides
17.
and
place cams
holes indicated, arrow
pointing towards the front.
turn the cams
right to x the front.
Ca
into the
Ca
to the
step 2.6
important!
make sure the
!
angle between
14
16
and
and
Fi
the drawer front
the drawer sides
17
is 90° before the drawer
18
bottom
as shown.
to adjust the angle between
the drawer sides and the
front push the tting
sidewards.
is xed using Fi
Ca
16
17
90°
14
18
14
Ca
ø15 x 10.5mm cam x
4
Ca
16
back fitting w. ø3.5 x 15mm screw xFi2
Fi
17
Fi
see details.
350808-13
Fi
Fi
Fi
12
assembly instructions
step 2.7
place the drawer runners
DL
and DR onto the drawer
16
sides
and 17 and push
them onto the back of the
14
front
x the drawer runners
and
16
.
DL
DR
to the drawer sides
and 17 using screws Bo
into the holes indicated.
step 2.8
Bo
ø3 x 12mm screw x
DL
Bo
Bo
Gm
DL
16
DL
4
450mm drawer runner, left x
1
DR
450mm drawer runner, right x
14
Bo
DR
1
Bo
17
x the metal handles Gm
14
to the drawer front
Hd
using screws
.
step 2.9
slide the drawer onto
the runners and into the
wardrobe.
54mm handle x
Gm
2
Gm
14
Hd
m4 x 20mm screw xHd2
Hd
13
350808-14
assembly instructions
step 3
assembly of the doors.
step 3.1
place the cup hinges Mf
into the holes indicated
12
on the doors
x the hinges using
screws
Bo
.
.
ø3 x 12mm screw xBo12
Bo
12
12
Mf
ø26mm cup hinge x
6
Mf
Mf
Bo
12
Bo
Bo
Mf
x
2
350808-15
14
assembly instructions
step 3.2
slide the cup hinges Mf
the crossplates
Mc.
x the hinges using the
premounted screw in the
crossplates.
see details below on how
to t the cup hinge
the cross plate
Mc.
onto
Mf
onto
Mf
!
Et
self adhesive bumper, ø10 x 3mm x
m4 x 20mm screw xHd2
12
Gm
54mm handle x
4
Et
Et
2
12
Mc
Mf
!
Mc
x the metal knobs
to the doors 12
screws
Hd.
place the self adhesive
bumpers
stops
Et onto the door
Pm
.
Gm
using
Gm
Hd
Hd
Gm
Et
15
Et
350808-16
assembly instructions
step 3.3
adjusting the doors
left/right.
a:
to adjust the door
towards the left hand
side - turn the adjusting
screw to the right.
b:
to adjust the door
towards the right hand
side - turn the adjusting
screw to the left.
adjusting the doors
forwards/backwards.
a:
b:
a:
loosen the xing screw.
b:
push the cup hinges /
the door forwards or
backwards to adjust.
c:
tighten the xing screws
of all the crossplates.
adjusting the doors
up/down.
a:
loosen the two premounted screws of each
crossplate, but only as
much as it will allow the
cross plate to move up and
down.
a:
a:
b:
b:
c:
c:
b:
push the the door up or
down to adjust.
c:
tighten the pre-mounted
screws of all the
crossplates.
if you need help or have damaged or missing parts, call the argos customer helpline: 03456 400 800
home retail group - 489-499 avebury boulevard - saxon gate west - central milton keynes mk9 2nw
350808-17
16
A Guide to
Wall Mounting & Fixings
IMPORTANT:
When drilling into walls always check that there are no
hidden wires or pipes etc. Make sure that the screws and
wall plugs being used are suitable for supporting your unit.
Consult a qualified tradesperson if you are unsure.
HINTS:
1) General Rule Always use a larger screw and wall plug if you are not sure.
2) Ensure you use the recommended drill bit to match the wall plug and hole size.
3) Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4) Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure the plug is fitting below the ceramic
tile to avoid splitting or cracking.
5) Ensure wall plugs are well fitted and are a tight fit in the drilled hole.
Types Of Walls
You can use one of the following types
of wall plug if your walls are made of
brick, breeze block, concrete, stone,
wood or plaster board.
No.1 "Standard" Wall Plug
General Wall Materials
These come in various sizes and are made
from plastic or sometimes wood fiber.
No.2 "General Purpose" Wall Plug
Aerated / Breeze Block
No.3 "Shield Anchor" Wall Plug
Heavy Loads
For use with heavier loads such as TV
& HiFi Speakers and Satellite Dishes etc.
No.4 "Cavity Fixing" Wall Plug
For use with plaster board partitions or
hollow wooden doors.
No.5 "Cavity Fixing - Heavy Duty"
Wall Plug
No.6 "Hammer Fixing" Wall Plug
For use with walls stuck with plaster
board. The hammer fixing allows it to
be fixed to the wall rather than the plaster
board. Always check the fixing is secure
to the retaining wall.
CARE & MAINTENANCE
SAFETY
Always check the fitting and
location to ensure your safety in
and around the home.
Generally aerated blocks should not be
used to support heavy loads, use a
specialist fitting in this case.
For light loads, a General Purpose Plug
can be used.
For use when fitting or supporting heavy
loads such as shelving, wall cabinets,
coat racks.
FITTING
From time to time check the fitting
to ensure the wall plugs or screws
do not become loose.
Loading...