Argos 404-4842 ASSEMBLY INSTRUCTIONS

Page 1
Assembly Instructions – Please keep for future reference
Important – Please read these instructions fully before starting assembly
Length - 201cm
Width - 145cm
Height - 120cm
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Issue 1 - 25/03/15
Dimensions (5')
Length - 211cm
Width - 160cm
Height - 120cm
Dimensions (4'6)
404/4842
400/8792
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
1
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough
space to layout the parts before starting.
• Assemble the item as close to its final position (in the same
room) as possible.
• Dispose of all packaging
carefully and responsibly.
• Place the product on flat and
steady surface during use.
• Assemble on a soft level surface to avoid damaging the unit or your floor.
• Keep these instructions for further use.
• To ensure an easier assembly, we strongly advise that all fittings are only finger tightened during initial assembly. Only upon completion of the assembly should all fixing points be fully tightened.
Care and maintenance
Page 3
Please check you have all the parts listed below
Components - Parts
2
Headboard panel (145 x 80cm) (160 x 80cm)
1
2
Footboard panel (145 x 80cm) (160 x 80cm)
Side rail x 2 (193.7 x 10.8cm) (203.7 x 10.8cm)
4
3
End support x 2 (136.5 x 4cm) (151.7 x 4cm)
5
Central support (183 x 9cm) (187.8 x 9cm)
6
8
Bentwood slat x 32Support leg x 2
(24 x Ø2.5cm)
7
If you have damaged or missing components, call the Customer Helpline:
0345 6400 800
Headboard post x 2
(45 x Ø3.8cm)
Page 4
Components - Fittings
A
Rubber washer x 8
Please check you have all the fittings listed below
Note:
The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Plain washer x 22
Allen key x 2
If you have damaged or missing components, call the Customer Helpline:
0345 6400 800
B
C
D E F
G
Nut x 4
3
25mm Allen screw x 415mm Allen screw x 12
H
J
K
45mm Allen screw x 2
Central plastic cap x 16
Plastic cap x 32
Ruler - Use this ruler to help correctly identify the screws
0
5
10 15 20 25 30 35 40
45
50
55
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100105 110 115120 125 130 135 140 145 150
1 2 3 4 5 6
Ruler/tape measure
32mm Allen screw x 4
Page 5
Step 1
Assembly Instructions
Assembling posts
Place headboard panel
face down onto a
clean flat surface.
Note:
Fixing holes for posts should be facing up.
Secure headboard posts
to headboard panel using fixings
and .
A
2
1
B
1
4
Step 2
Front
Back
A
B
Step 2
Assembling side rails
a: With help, assemble
side rails to the headboard using fixings
, , and .
Note: Ensure the metal brackets are at the bottom as shown.
b: Assemble footboard
to the side rails using fixings and .
3
B
C E
B
D E
F
B
D
F
E
B
3
4
4
2
E
a:
b:
C
4
Brackets at bottom
A
B
2
1
3
2
4
4
Page 6
Assembly Instructions
Step 3
5
5
5
4
A
B
Step 4
G
B
A
A
B
B
6
7
5
5
Holes inside
4
7
Securing end supports
Locate end supports into the metal brackets on the inside of side rails
.
Note:
Ensure the fixing
holes are on the inside as shown.
Secure using fixings and .
5
4
B
A
Assembling central support
Locate central support
in between end supports and secure using fixings and .
Assemble support legs
to the underside of central support using fixings and .
6
5
A
B
7
6
B
G
Page 7
Assembly Instructions
Step 5
6
Assembly is complete.
K
J
J
K
K
8
8
8
8
4
6
Attaching slat caps
Assemble plastic caps
onto one end of bentwood slats .
a: Fit plastic caps
into the slotted holes in side rails
as shown.
b: Fit bentwood slats
into both sides of
central plastic caps
before pushing caps into central support .
8
8
6
8
a:
b:
J
J
K
8
8
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Home Retail Group. 489-499 Avebury Boulevard. Saxon Gate West. Central Milton Keynes. MK9 2NW
4
K
Loading...