MADE IN
BRITAIN
Dimensions
Width - 54.5cm
Depth - 33cm
Height - 65cm
3 Basket 2 Shelf Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 02/07/12
Important - Please read these instructions fully before starting assembly
906/4638
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 13kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D1469A)
(597 x 328mm)
4
2 3
Right Side (D1470A)
(597 x 328mm)
Top/Base (D1468A)
(545 x 329mm) x 2
5
6
Divider (D1472A)
(597 x 312mm)
These 2 holes are on
the opposite surface
Shelf (D1471A)
(238 x 310mm) x 3
Back (D1775A)
(493 x 597mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
B
Metal dowel (F901) x 12
C
D
Large locking
nut (F900) x 12
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
F
Feet (F854) x 4
E
25mm Screw (F50) x 4
G
Shelf support (F121) x 12
45mm Screw (F65) x 3
A
Wooden dowel (F22) x 4
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Prepare the left side
Insert 4 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 1
C
C
C
C
C
C
1
Step 2
Prepare the right side
Insert 4 large locking
nuts into the right
side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
C
2
Step 3
Prepare the divider
Insert 4 large locking
nuts into the divider
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
C
3
1
Note: The left side only has
holes on the surface shown.
Note: The divider has holes
on both surfaces.
Note: The right side only has
holes on the surface shown.
C
C
C
C
C
C
C
C
C
C
C
C
1
2
3
Assembly Instructions
5
Step 4
Finished
front edge
Prepare the base
a: Screw the 4 feet
onto the base using
screws .
Note: The feet must be
fitted close to the edges
of the base for maximum
stability, as shown.
Turn the base over
b: Screw 6 metal dowels
. into the base .
Note: Tighten the metal
dowels up fully against
the panels.
B
4
4
4
Finished
front edge
B
B
B
B
B
B
B
4
E
F
F
F
F
Turn the base over
a:
b:
F
E
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 5
Fit the divider
Push the divider onto
the base .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
3
4
C
3
Step 6
Join the right side and
base
Push the right side
onto the base .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
4
C
2
Note: The right side only has
holes on the surface shown.
2
4
3
Note: The divider has holes
on both surfaces.
B
C
Assembly Instructions
7
Step 7
Step 8
Prepare the back
Tap 4 wooden dowels
into the back .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Finished
front edge
4
1
Fit the left side
Push the left side
onto the base .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
1
4
C
1
A
A
A
A
10mm
A
A
6
6
Assembly Instructions
8
Step 9
Step 10
Fit the back
Position the back
between the left side
and right side and
gently push in its
wooden dowels .
1
6
1
2
6
2
Prepare the top
Screw 6 metal dowels
into the top .
B
4
Finished
front edge
B
B
B
B
B
B
4
A
2 holes
1 hole
Assembly Instructions
9
Step 11
Fit the top
Lower the top down
onto the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the left side , right
side and upright .
4
4
C
1
2 3
1
2
3
G
x 4
G
x 4
Fit the shelf studs
For each of the 3
shelves , insert 4 shelf
studs .
Make sure that the plastic
sleeve is fully pushed
onto the shelf stud.
G
G
x 4
Step 12
5
G
Finished
front edge
Assembly Instructions
10
Step 13
Step 14
Secure the shelves
2 people are needed
here
At the front of the unit,
hold the shelves in
position.
From the rear of the unit
screw through the back
. and into the back
edge of the shelves
using screws .
Fit the shelves
Lower the 3 shelves
down onto the shelf
studs .
5
G
5
5
5
5
5
5
5
6
D
6
5
D
D
D
Finished
front edge
Front
of unit
Back
of unit
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR2773
Step 15
Assembly is complete
Loading...