Argos 412/1961, 402/3124, 395/7655 User guide

Sparkle - 5฀Drawer฀Chest

Assembly Instructions - Please keep for future reference

412/1961

395/7655

402/3124

Dimensions

Width - 75.1cm

Depth - 39.6cm

MADE IN

Height - 90.1cm

Important -฀Please฀read฀these฀instructions฀fully฀before฀starting฀assembly

If you need help or have damaged or missing parts, call the Customer฀Helpline:฀03456฀400800

BRITAIN

Issue฀1฀-฀03/06/15

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 31kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

Care and maintenance

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.

• Dispose of all packaging
carefully and responsibly.

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

1

If฀you฀have฀damaged฀or฀missing฀components,฀call฀the฀

Components - Panels

Customer฀Helpline:฀03456฀400800฀

numbers below

Please check you have all the panels listed below

3

Top

(DF3812)

(75.1฀x฀39.6cm)

quoting the reference

12

Left฀Side (DF3867)

(88.6฀x฀37.2cm)

56

Drawer฀Front (DF3814)

(73.7฀x฀16.2cm)฀x฀5

8

Drawer฀Back฀(W684-124)

(68.4฀x฀12.4cm)฀x฀5

Right฀Side (DF3868)

(88.6฀x฀37.2cm)

Left฀Drawer฀Side฀(W370-124LH)

(37฀x฀12.4cm)฀x฀5

4

Rail (DF3813)

(71.7฀x฀6cm)฀x฀3

7

Right฀Drawer฀Side฀(W370-124RH)

(37฀x฀12.4cm)฀x฀5

910

Drawer฀Base฀(T695-367)

(69.5฀x฀36.7cm)฀x฀5

Back฀(X861-743)

(86.1฀x฀74.3cm)

2

If฀you฀have฀damaged฀or฀missing฀components,฀call฀the฀

Components - Fittings

Customer฀Helpline:฀03456฀400800฀

numbers below

quoting the reference

Please check you have all the fittings listed below

Note:฀The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

AB

Metal฀dowel฀(F901) ฀x฀20

DEF

Wooden฀dowel฀(F22) ฀x฀10

GHI

25mm Screw฀(F50) ฀x฀15

J

Plastic฀Nail฀(F91) ฀x฀4

M

Nail฀(F51) ฀x฀25

9mm฀Screw฀(F74) ฀x฀10

K

Wedgefix฀(F639) ฀x฀20

Large฀locking฀

nut฀(F900) ฀x฀10

C

Small฀locking฀

nut฀(F3) ฀x฀10

Knock-in฀Peg฀(F171GY)฀฀x฀20

9mm Screw฀(F73) ฀x฀20

L

Handle฀(F569) ฀x฀5

Drawer฀runner฀(F1004) ฀x฀10

N

Strap Screw Washer x 2

Overbalance฀protector฀kit฀(F269) x฀1

Tools required

Eye฀protection฀

RuleScissorsHammer

Cross-head฀

screwdriver

(when฀using฀a฀

hammer฀or฀drill)

Ruler -฀Use฀this฀ruler฀to฀help฀correctly฀identify฀the฀screws

Electric฀drill

(only฀use฀

when฀drilling฀

into฀walls)

mm102030405060708090100110120130140150160170

3

Assembly Instructions

If฀you฀have฀damaged฀or฀missing฀components,฀call฀the฀

Customer฀Helpline:฀03456฀400800฀quoting the reference

numbers below

Step 1

Prepare฀the฀5฀drawer฀

fronts

Screw 2 metal dowels
into each of the drawer
fronts .

Note: Tighten the metal
dowels up fully against
the panels.

5

A

Step 2

Prepare฀the฀drawer฀

sides฀

Insert a small locking

C

nut into the hole
shown on the left drawer
side and the right

6

drawer side .

7

A

A

A

5

x 5

C

C

6

C

7

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

Step 3

Attach฀the฀drawer฀

sides฀to฀the฀drawer฀

fronts

Push the left drawer sides
. and right drawer sides

6

7

. onto the back of the
drawer fronts .

Turn the small locking

C

nuts on the left
drawer side and right
drawer side .

5

6

7

6

x 5

5

x 5

x 5

C

7

A

Note: Turn the locking

C

nuts clockwise to
secure panels - more
than 1/2 a turn.

4

Assembly Instructions

Step 3

Fit฀the฀drawer฀base

Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .

5

67

9

Step 5

Fit฀the฀drawer฀back

Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .

Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .

67

9

8

67

8

8

F

9

7

x 5

6

F

F

5

F

F

8

9

6

7

x 5

Step 6

Attach฀the฀handles

Attach a handle to
each of the drawer fronts
. using screws .

5

Note: Do not
overtighten the screws.

L

G

Step 7

Fit฀the฀wedgefixes

Turn the 5 drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.

K

G

G

G

5

K

K

K

L

K

x 5

K

x 5

5

Assembly Instructions

Step 8

Prepare฀the฀left฀side

a:฀Place 5 runners on

the left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .

1

b:฀Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .

c:฀Screw 3 metal

dowels into the left
side .

Insert 2 large locking
nuts into the left side
. .

1

Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.

A

1

B

M

I

M

I

1

a:

b:

Finished฀

front฀edge

I

I

M

Finished฀

front฀edge

I

M

I

I

I

M

M

1

I

I

I

1

M

M

I

I

Tap 2 wooden dowels
into the left side .

1

Note: Wooden dowels

must not stick out from
the edge by more than
10mm or they may
damage other panels.

D

B

B

D

A

1

B

10mm

D

D

c:

A

Finished฀

front฀edge

A

6

Assembly Instructions

Step 9

Prepare฀the฀right฀side

I

M

a:฀Place 5 runners on

the right side as

M

2

shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .

b:฀Slide the runner

I

M

back the other way and
fit the 2nd screw into

I

the corresponding hole
in the right side .

2

c:฀Screw 3 metal

dowels into the right
side .

Insert 2 large locking
nuts into the right
side .

Tap 2 wooden dowels
into the right side .

A

2

B

2

D

2

a:

b:

I

I

2

I

M

M

I

I

I

I

I

M

I

2

M

M

Finished฀

front฀edge

I

Finished฀

front฀edge

B

c:

A

A

A

2

Finished฀

front฀edge

D

B

D

7

Assembly Instructions

Step 10

Prepare฀the฀3฀rails

Insert 2 large locking
nuts into each of 3

B

the rails .

Tap 2 wooden dowels
into each of 3 the rails .

4

D

4

Step 11

Fit฀the฀the฀3฀rails฀to฀

the฀right฀side

Push the 3 rails onto
the right side .

Use a screwdriver to
tighten the large locking

B

nut fitted to each of
the rails .

4

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

4

2

B

B

D

B

4

x 3

D

A

B

2

4

4

4

Note: Support
these 2 rails
until the left side
has been fitted
in the next step.

Step 12

Fit฀the฀left฀side

Push the left side
onto the rails .

Use a screwdriver to
tighten the large locking

B

nut fitted to each of
the rails .

4

1

4

4

4

1

4

Finished฀

front฀edge

8

Assembly Instructions

Step 13

Prepare฀the฀top

Screw 4 metal dowels
into the top .

3

A

Step 14

Fit฀the฀top

Push the top onto
the assembly.

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each of the sides and
. .

2

3

B

1

A

A

A

A

3

Finished฀

front฀edge

3

2

1

Step 15

Fit฀the฀4฀plastic฀nails

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

2

J

1

Finished฀

front฀edge

J

2

J

J

1

J

9

Assembly Instructions

Step 16

Fit฀the฀back

a: Square up the unit by

making sure that
measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the

E

outside edges of the

10

back .

Note: Nails should be
spaced about 150mm
apart.

Carefully฀stand฀the฀

unit฀up฀for฀the฀next฀

step.

10

The฀measurement฀from฀top฀corner฀X฀to฀bottom฀corner฀X฀must฀be฀

a:

equal฀to฀the฀measurement฀from฀top฀corner฀Y฀to฀bottom฀corner฀Y

b:

E

yy

xx

10

xx

Warning: The
unit is heavy.
Lift with care.

yy

Step 17

Fit฀the฀drawers

Starting with the bottom
drawer, slide both the
runners forward and
locate the drawer
sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .

Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.

M

67

M

H

H

M

2nd฀threaded฀

hole

7

H

H

6

Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.

H

10

Assembly Instructions

Step 18

Fit฀the฀overbalance฀

protector฀kit

To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an

N

alternative fixing method
of your choice.

Wall fixings are not
supplied as they will
need to suit the wall
type.

Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.

Wall fixing

(not supplied)

Attach the

strap to the wall

N

Strap

Washer

Screw

(not supplied)

Example

Strap

Attach the

strap to the unit

N

UNIT

Screw

Washer

Assembly฀is฀complete

If you need help or have damaged or missing parts, call the Customer฀Helpline:฀03456฀400800

and quote the reference numbers on the component pages.

Argos฀Ltd,฀489-499฀Avebury฀Boulevard,฀Central฀Milton฀Keynes,฀MK9฀2NW

11

ALR3198