Page 1
ALL IN ONE HALLWAY UNIT
392/9188
65cm
44cm
177cm
Issue 1- 30/03/15
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3..
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the using. Only use hand
screwdrivers
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Page 3
1 Top panel x 1
(65(w)cm x 21.5(d)cm)
4 Hook base bar x 1
(59(w)cm x 5(d)cm)
2 Upper right side panel x 1
(132(w)cm x 19.5(d)cm)
5 Long cross bar x 1
(59(w)cm x 8(d)cm)
6 Lower left side panel x 1
(43.5(w)cm x 42.5(d)cm)
3 Upper left side panel x 1
(132(w)cm x 19.5(d)cm)
7
Lower right side panel x 1
(43.5(w)cm x 42.5(d)cm)
8
Lower back panel x 1
(59(d)cm x 37(w)cm)
12 Long cross bar x 1
(64.5(w)cm x 8(d)cm)
9
Front panel x 1
(59(d)cm x 37(w)cm)
13 Cover panel x 1
(65(w)cm x 35.4(d)cm)
10
Bottom panel x 1
(59(w)cm x 39.3(d)cm)
14 Upper back panel x 1
(134(w)cm x 61(d)cm)
11
Short cross bar x 2
(42.5(w)cm x 8(d)cm)
Page 4
35mm Male camlock x 24
Female camlock x 28
30mm Wooden dowel x 16
Nut x 4
Hinge x 2
12mm Screw x 5 20mm Screw x 24
N
35mm Screw x 1
P
Washer x 2 Wall plug x 1
Q
61 x wercS mm214 x kcolmac elaM mm14
25mm Screw x 4Spring hinge x 1
Safety strap x 1
O
Lid x 8 Hook x 4
Page 5
Using Camlocks
Connect the male
camlock as directed in
the assembly instructions
using a screwdriver.
lnsert the female
camlock as shown in the
instructions
Note: ensure that the
arrow on the top of the
camlock points towards
the entry hole for the
male camlock.
Push the male camlock
into the entry hole.
Turn the female camlock
clockwise with a
screwdriver.
You should feel a click
when the camlock is
locked in place.
The joint is now secure.
Page 6
Insert 10 x 35mm male
camlock into inside of
top panel , upper right
side panel and upper
left side panel as
A
1
2
3
shown.
A
1
A
A
3
A
Fix 2 x hinge on Long
cross bar using 4 x
12mm screw as
G
5
F
shown.
A
F
G
2
F
F
A
5
A
A
6
Insert 14 x 35mm male
camlock into inside of
lower left side panel ,
lower right side panel
and long cross bar
A
6
7
12
as shown.
Attach 2 x short cross bar
11
to the lower left side
panel and lower right
side panel using 4 x
25mm screw as
6
7
I
shown.
A
A
7
A
11
I
A
11
I
A
A
12
Page 7
Insert 4 x wooden dowel
C
into inside of lower
right side panel .
7
Attach lower back panel
8
and front panel
9
to it using 4 x female
camlock as shown.
B
Tighten female camlocks
with a screwdriver.
Please refer to the “Using
Camlocks” section at the
front of this instruction for
further assistance.
Insert 2 x wooden dowel
C
into inside of lower
right side panel .
Attach bottom panel
7
10
to it using 2 x female
camlock as shown.
B
Tighten female camlocks
with a screwdriver.
10
8
9
C
B
7
C
Insert 6 x wooden dowel
C
into lower back panel
, front panel and
8 9
bottom panel .
10
Attach lower left side
panel to them using
6 x female camlock
6
B
as shown.
Attach long cross bar
12
to the lower left side
panel and the lower
right side panel using
6
7
2 x female camlock
as shown.
Tighten female camlocks
with a screwdriver.
B
C
C
7
6
C
B
12
Page 8
7
Insert 4 x wooden dowel
into long cross bar
C
as shown.
Attach hook base bar
and long cross bar
to upper right side panel
using 4 female
2
camlock as shown.
B
Tighten female camlocks
with a screwdriver.
5
4
5
C
4
B
5
B
8
Attach upper left side
panel to the hook base
bar and the long cross
bar using 3 x female
camlock as shown.
Tighten female camlocks
with a screwdriver.
3
4
5
B
2
3
B
4
B
5
Page 9
9
Attach top panel to
1
the upper right side panel
2
and upper left side
panel using 4 x female
camlock as shown.
3
B
Tighten female camlocks
with a screwdriver.
3
1
B
2
10
Insert 4 x nut into the
lower left side panel
and lower right side panel
7
and adjust the threaded
hole of nut and the
predrilling male camlock
hole of side panels in a
line.
Insert 4 x 41mm male
camlock into the
predrilling male camlock
holes of side panels and
screw them into nuts .
E
6
E
D
E
D
D
E
6
E
7
Page 10
11
Connect the assembled
upper part to the
assembled lower part
using 4 x female camlock
B
as shown.
Tighten female camlocks
with a screwdriver.
B
12
Attach cover panel
to the long cross bar
using 4 x 12mm screw
as shown.
13
5
F
13
F
Page 11
13
Fix spring hinge on
H
the lower right side panel
and the cover panel
7
13
using 4 x 12mm
screw as shown.
J
13
7
H
14
Fix 4 x hook on the
hook base bar using
8 x 12mm screw as
shown.
attach upper back panel
14
to the assembled part
using 24 x 20mm screw
K
as shown.
P
4
F
J
K
14
4
P
F
Page 12
15
Fix unit to wall using 1 x
12mm screw , 1 x
safety strap , 2 x
washer , 1 x 35mm
screw and 1 x wall
plug as shown.
M
O
Cover 8 x lid on the
J
L
N
Q
exposed female camlock
holes as shown.
J
O
N
L
M
Q
Q
Q
Q
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos LTD. 489-499 Avebury boulevard, Central Milton Keynes, MK9 2NW
0345 640 0800
Page 13
Loading...