Argos 392/8701, 427/0795 User guide

Ashdon Table

Assembly Instructions - Please keep for future reference 392/8701

427/0795

Dimensions

Width - 149.8cm

Depth - 72.5cm

Height - 75cm

Important - Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline:

Argos = 0345 640 0800

Issue 1 - 09/04/15

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Check you have all the

components and tools listed on
the following pages.

• Remove all fittings from the

plastic bags and separate them
into their groups.

• Keep children and animals

away from the work area, small
parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before
starting.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use
bleach or abrasive cleaners.

• During assembly do not stand

or put weight on the product, this
could cause damage.

• Assemble the item as close to

its final position (in the same
room) as possible.

• Assemble on a soft level

surface to avoid damaging the
unit or your floor.

• Parts of the assembly will be

easier with 2 people.

• From time to time check that

there are no loose screws on
this unit.

• We do not

recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Unit weight: 18 kgs.

• This product should not be

discarded with household
waste. Take to your local
authority waste disposal centre.

Handy Hints

• Assemble all parts and bolts

loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.

• Regularly check and ensure

that all bolts and fittings are
tightend properly.

1

If you have damaged or missing components, call the

Components - Parts

Customer Helpline: Argos = 0345 640 0800

Please check you have all the parts listed below

Table top

1 Leg x 4

(149.8 x 72.5 x 10.5cm)

2

(72 x 6.5/6.5cm)

Components - Fittings

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.

A

Stud bolt x 8

D

Washer x 8

Tools required

Flathead screwdriver

B

Insert nut x 4

E

Spring Washer x 8

C

Nut x 8

F

Spanner x 1

2

Assembly Instructions

Step 1

a: Attaching insert nut

Position the leg as
shown and insert the
insert nut into hole on

B

the top of leg.

b: Attaching bolt

Align the fixing holes on
the insert nut by turning it
using a flathead
screwdriver.

Then fix bolt into the
insert nut on leg as
shown.

Repeat this step to
assemble the other
legs.

2

A

2

a: b:

B

2

B

A

A

2

A

A

2

2

Step 2

Attaching legs

Place the table top on
a flat protected surface.

Position the legs on
the table top as

1

shown. Insert the bolts
on the legs into holes on
table top and fix using

C

nuts , washers and
spring washers .

Tighten nuts using
spanner .

F

Carefully turn over the

table by holding the legs
and place on a firm
surface. At least 2 people
are required to lift this
table.

1

2

D

E

2

D

E

C

2

2

D

E

C

D

E

C

C

E

D

C

E

D

D

1

E

C

C

1

2

2

D

E

D

E

C

C

E

D

C

E

D

Assembly is complete.

If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800

3

Dear Customer

Please note that the product you have purchased is a natural
living timber.

Just like nature itself, wood varies in shape and colour. Knots,

vein patterns, resin pockets and colour differences contribute to
giving the piece of furniture its beauty and form - a natural part of
solid wood.

Although the tree has been cut down and dried, it is still alive and
therefore will react to high and low temperatures, light, humidity,
drought and time.

In cold and dry periods, the wood contracts which may lead to
small cracks in the piece of furniture. The reverse happens in
warm and humid periods where the wood expands and this may
result in slight unevenness.

The colour of the wood also changes with time, particularly if the
furniture is placed in a light place. This is a natural process and
part of owning a piece of furniture made of solid wood.

Any flexing that has occurred during transport will re-correct itself
once this product is correctly assembled.

Tighten all joints of the furniture after six months.

Please keep these instructions in a safe place for future use.

4