Page 1
10 Tier Rolling Shoe Rack
Assembly Instructions - Please keep for future reference
390/9665
Dimensions
Width - 73cm
Depth - 22.5cm
Height - 163.5cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 2 - 27/08/14
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
1
Page 3
Components - Parts
If you have damaged or missing components,
call the Customer Helpline: 03456 400800
Please check you have all the fittings listed below
Lower Side Frame x 2
1
710 mm Black Coated Steel Tube x 20
3
Upper Side Frame x 2
2
694 mm Black Coated Steel Tube x 2
4
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
18 mm Screw x 40
Tools required
Screwdriver
28 mm Screw x 4BPlastic Insert x 4CRegular Castor x 2DCastor with stopper x 2
E
2
Page 4
Assembly Instructions
Step 1
Connect 710 mm
3
Black Coated Steel Tube
with Upper Side
2
Frame using Screw.
Connect 694 mm
A
4
Black Coated Steel Tube
with Upper Side
2
Frame using 28mm
B
Screw.
See fig 1.
Now finished the upper
part of shoe rack.
2
A
A
A
A
A
3
3
3
3
3
3
4
B
4
2
A
B
A
A
A
A
fig 1.
Step 2
Repeat above processes
for the lower part of shoe
rack.
Connect 694 mm
Black Coated Steel Tube
with Lower Side
Frame.
See Fig 2.
Insert Plastic Insert to
1
Lower Side Fram and
insert Regular
Castors and Castors
with Stoppers
respectively.
4
1
C
D
E
1
A
A
A
B
A
A
C
E
3
3
3
3
3
3
4
B
1
A
A
A
B
A
C
C
E
D
fig 2.
3
Page 5
Assembly Instructions
Step 3
Connect the uppper part
of shoe rack with lower
part of shoe rack
together.
Note: It would be useful
to ask someone to help
you at this stage.
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Loading...