Argos 432-9426, 432-9433, 432-9440, 3851768 User guide

Floor Lamp-432-9426/9433/9440/3851768

Assembly and User Instructions – Please keep for future reference

Important –Please read these instructions fully before using
If you need help please call our Customer Services on 0345 640 3030

Contents

Section Page

Parts and Component list 2

Safety Information 3

Maintenance 3

Installation 4

Produced for Argos, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

1 Customer Helpline 0345 640 3030

Parts and Components Listing

B

C

A

D

E

F

G

A. Fitting x 1

B. Fixing nuts & Washers x 2 (1 pre-fitted)

H

I

J

K

C. Pole x 2 (1 pre-fitted)

D. Curved Glass Shield (pre-fitted)

E. Adjusting Arm for Child lamp x 1

F. Round Glass Shield (pre-fitted)

G. Allen Key x 1

H. Dimmer Fuse 2.5A x 2— (x1 pre-fitted, x1 Spare )

I. Spanner x 1

J. Plug (pre-fitted)

K. Spare grub screw x 1

2 Customer Helpline 0345 640 3030

Safety Information

IMPORTANT – Please read these instructions fully before installation and keep for future reference

For your safety, this product must be installed in
accordance with local building Regulations. If in any
doubt, or where required by law, consult a competent
person who is registered with an electrical self
certification scheme. Further information is available
online or from your local authority.

IMPORTANT -This product has been designed for
non-professional, domestic use only.

IMPORTANT - Carefully unpack and examine the
product for any damage. If you think there is a defect,
do not use the pro duct an d contact our customer
services on 0345 640 3030.

IMPORTANT - Dispose of all packaging correctly and
responsibly and in accordance with all local laws and
regulations. Never leave packaging components within
reach of children as they can be a source of danger.

IMPORTANT – Before inserting or replacing bulb(s)
ensure the power is switched off and the bulb(s) have
cooled down.

WARNING – This is a Class I product and requires an
earth connection.

WARNING – Do not modify or alter any produc t be­fore or after installation. This may render the product
un-safe.

WARNING - This product is not intended for use by
persons (including children) with reduced physical,
sensory and mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the product by persons
responsible for their safety.

WARNING - Children should be supervised to ensure that
they do not play with the product.

WARNING - Do not place th is fitting in a damp
atmosphere.

WARNING – Do not remove the metall ic refl ective
shield.

WARNING – If the Glass shi elds are d amaged or bro­ken they must be replaced before continuing to use the
Floor Lamp.

CAUTION - Ensure the power is switched off before
cleaning or carrying out any maintenance.

SPECIAL NOTE—Should the dimmer fail to operate
as normal, please check and replace the fuse in the
dimmer unit (spare fuse supplied).

WARNING - Accessible parts become hot during use,
young children must be kept away.

Maintenance

Maintenance

CAUTION! Alw ays dis connect power supply when servicing or cl eaning.

Cleaning

- Use a clean dry soft or slightly damp cloth.

- Do not use abrasive cloths or polishes as this may cause damage to the product.

Changing the bulbs

IMPORTANT! Ensu re that th e bulb has coo led down before r eplacin g.

- Ensure that the power supply has been disconnected.

- Carefully remove the protective glass shields.

- Insert replacement bulbs avoiding contact with your fingers as this will shorten the bulb life.

- If the bulb comes into contact with fingers clean the bulb with a soft dry cloth or tissue.

IMPORTANT!

If the external flexible cable or cord if this Luminaire is damaged it shall be exclusively replaced by the
manufacturer or his service agent or similar qualified person.

3 Customer Helpline 0345 640 3030

Installation

Installation

IMPORTANT ! - Electrical connections m u st be car-

ried out by a suitably qualified person and in accordance
with all relevant local building and installation regulations.
If in doubt consult a qualified electrician.

Installation

1. Insert the upper section into the head and secure using
the Allen key provided.

2. Screw the wired pole onto the bottom of the upper
section taking care not to twist or damage the cable.

3. Screw the non wired pole onto the bottom of the upper
section.

4. Place the assembled poles through the base cover and
base weight, with the lower sections in place pull the
excess cable through the base taking care not to twist
the cable.

5. Secure the lower sections to the base with the washers
and hex nuts using the spanner supplied.

6. Screw the adjuster arm into the Child light.

7. Remove the curved glass shield. Insert R7S 118mm
into top head lampholder (not supplied). Refit the
curved glass shield over top of bulb.

Head

1

7

Upper section

6

8. Remove one screw from the round glass shield from
the adjustable head and slide to one side to gain
access. Insert the G9 bulb (not suppled) into the lamp
holder. Move the round glass shield back into place
and re insert screw.

9. Connect the plug to a normal household socket and
using the rotary dimmer controls turn on the light to
test. The rotary controls are also used to dim the light
level for both lights.

REPLACING THE BULBS

REPLACE THE BULB BY USING GENTLE PRESSURE WHEN INSERTING IT INTO THE
LAMP HOLDER, MAKING SURE THAT YOU DON’T HAVE DIRECT CONTACT WITH THE
BULB AS THIS WILL SHORTEN THE LIFE OF THE BULB, USE A LINT FREE CLOTH OR
SIMILAR

REPLACEMENT LAMP
Maximum wattage – See
lamp holder
Light bulb shape - See lamp
holder

3 2

Wired pole

8

4

Base

APPROVED

Q.C

4 Customer Helpline 0345 640 3030

11/04/2016

ISSUE 4

7

5