Page 1
1 Drawer Entertainment Unit
Assembly Instructions - Please keep for future reference
033 xx 3042
424 / 2077
427 / 1055
609 / 6974
Dimensions
Width - 101.6cm
Depth - 38.8cm
Height - 34.4cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08450613967
Please turn to back page for important information when contacting Customer Helpline.
01709 534123
Rev A - 08/10/2012
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Do Not dispose of packaging
until assembly complete.
Dispose of all packaging
carefully and responsibly
when assembly complete.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
From time to time check that
there are no loose screws on
this unit.
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furnture.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Clean spills up immediately
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergants, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
1
Page 3
Components - Panels
Please check you have all the panels listed below
Important - Thick lines indicate finished edges
8800
8806
4472
622xx7000 624xx7006 623xx7000
Left drawer side (30x15cm) Drawer back (41.4x15cm) Right drawer side (30x15cm)
Top (101.6x38.8cm)
Plinth (91x76cm)
Drawer Bottom (42.6x29.8cm)
8801
8807
Bottom (91x36cm)
Backpanel (45.6x22.8cm)
8802
Left End Panel
(32.2x38.2cm)
8804
Division
(36x22.9cm)
8803
Right End Panel
(32.2x38.2cm)
8805
Draw Front
(45.8x23.8cm)
2
Page 4
If you have damaged or missing components, call the
Components-Fittings
Customer Helpline: 0845 0613967
for important information when contacting Customer Helpline.
01709 534123
Please turn to back page
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly, In some case more fittings
may be supplied than are required.
A
D
G
J
Large cam x 14
Code 760001103
20mm bolt x 2
Code 700002006
Assembly Screw x2
Code 690001075
8mm screw x 4
Code 700003510
H
E
K
B
Metal dowel x 18
Code 760003004
Knock-in Trim x 2
Code 684xx3040
9mm bolt x 2
Code 690001078
Runner x 2
Code 760001040
C
F
I
Small cam x 4
Code 760003005
Wooden dowel x 2
Code 770001006
Handle x 1
Code 653003512
Tools required
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Ruler - Use this ruler to help correctly identify the screws
40
50
60
70
80
90
100
3
0
mm
10
20
30
110
120
130
140
150
Drill
160
170
Page 5
Exploded View
Please check you have all the fittings listed below
8800
8802
8806
622xx7000
8804
8807
8801
8803
624xx7006
8805
4472
623xx7000
4
Page 6
Assembly Instructions
Step 1
Fitting dowels to top
panel.
B
Note: Insert metal
dowels as far as
B
shown by arrows.
Do not over tighten.
Step 2
Fitting cams to the
bottom panel.
Fittings you will need for this step:
B
x6
B
B
8800
B
Fittings you will need for this step:
A
x4
A
B
B
B
A
Note: Ensure cam
arrow points towards
the edge with hole.
Step 3
Fitting cams and
dowels to end panels.
Fit the cams and dowels
to the end panels as
shown.
A
8801
Fittings you will need for this step:
A
x4
B
x8
B
B
A
8802
A
A
A
B
B
A
5
A
B
8803
B
B
B
Page 7
Assembly Instructions
Step 4
Fitting cams & dowels
to the divider.
A
Note: Ensure cam
arrow points towards
the edge with hole.
Step 5
Attaching runners to
right end and divider
Position the runner so
that the second hole
from the front of the
runner lines up with the
pre-drilled hole nearest
to the edge of the panel.
Use screws to secure
the runner.
Front of runner
J
F
x2
x2
A
x2
A
A
8804
F
F
K
J
x4
8804
8803
Slide the runner forward
revealing the back of the
runner. The second hole
to the back of the runner
should now line up with
the second pre-drilled
hole.
Step 5
Step 6
Fitting cams to the
plinth panel.
A
Note: Ensure cam
arrow points towards
the edge with hole.
A
x4
J
K
A
A
J
K
8806
A
A
6
Page 8
Assembly Instructions
Step 7
Drawer assembly
a: Insert dowels into
drawer front.
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
(x4)
C
(x4)
A
B
B
B
B
B
8805
Right hand side
623xx7000
b: Insert small cams
into left
and right
drawer sides.
Note: Ensure cam arrow
points towards the edge
with hole.
622xx7000
623xx7000
c: Insert wooden dowels
in drawer back
into holes in
624xx7006
left
622xx7000
right hand
623xx7000
drawer sides.
C
Left hand side
622xx7000
Left hand side
622xx7000
C
C
C
C
Drawer Back
624xx7006
Continued on next page.
7
Right hand side
623xx7000
Page 9
Assembly Instructions
Step 7 - Continued
Drawer assembly
Continued...
d: Slide drawer bottom
into grooves in the left
and right drawer sides
and the drawer back.
Ensure foil on the
drawer bottom is facing
upwards.
e: Locate the metal
dowels (already inserted)
in the drawer front into the
small cams in the left and
right hand drawer sides.
D
E
622xx7000
SLIDE!
622xx7000
624xx7006
4472
Foil Face
623xx7000
Turn cam 180 degrees
to lock
f: Secure handles to the
drawer front.
8805
D
(x2) (x1)
I
F
8805
4472
623xx7000
D
D
I
8
Page 10
Assembly Instructions
Step 9
Attach bottom and
plinth to right end.
Connect the cams in the
bottom panel and
plinth panel to the
right hand end panel
8803
.
8801
8806
8806
8801
Ensure plinth sits
flush.
CAUTION!
An additional person
will be required to hold
the plinth for support.
Step 10
Turn unit so the
finished edge is facing
the floor.
Connect the cams in the
bottom panel and
plinth panel to the
left hand end panel
8802
8801
8806
8806
8801
8803
Ensure plinth is
not overhanging.
8802
9
Page 11
Assembly Instructions
Step 11
Attach the division
Line the wooden dowels
already inserted in the
division panel with
the center holes in the
bottom panel.
Fix with screws
8804
G
G
x2
8804
G
G
Step 12
Attaching the trims
Locate the notch on
the trim into the grooves
in the end panels.
Ensure the trims are
positioned flush with the
bottom of the unit.
To insert trims use a
hammer, place a
cardboard packing piece
between the hammer
and the trims to
protect the trims.
Ensure that the trims
are inserted fully.
E
x2
E
E
10
Page 12
Assembly Instructions
Step 13
Slide in backpanel
Slide the back panel into
the grooves in the division
and right hand end panel.
SLIDE!
8807
8804
8803
Step 14
Attach top panel
Connect the dowels in the
top panel to the cams in
the end panels and the
division panel.
8800
8802
8804
8803
11
Page 13
Assembly Instructions
Step 15
Locate drawers
For this step we
recommend you follow
the helpful hints page.
H
(x2)
H
2nd HOLE
12
Page 14
Assembly Instructions
Step 26
Locate drawers helpful
hints
a: Pull sliding part of
drawer runners out
so they are fully
extended.
K
b: Locate drawer onto
runners.
c: Locate screwdriver
into second threaded
hole in drawer runner .
K
d: Keeping screwdriver
in place push the drawer
closed.The screwdriver
will push against the end
panel and extend the
drawer runner .
K
A
C
B
K
K
D
K
2nd hole
e: Pull drawer out slowly
and line the hole in the
drawer side with the 2nd
threaded hole in the
runner . Now insert
bolts through the
drawer side and
into threaded hole in
runner .
O
H
K
f: Now insert bolts
through the drawer side
and into threaded hole in
runner .
13
K
E
l
H
F
I
H
K
2nd hole
Page 15
Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
8am - 4.30pm (Monday to Thursday)
01709 534123
0845 061 3967
(by contacting the customer service line your statutory rights are not affected)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
8am - 2.30pm (Fridays)
You can also e-mail your requests to us at:
customer.helpdesk@addspacefl.co.uk
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
14
Page 16
Notes
Loading...