Argos 3311208 ASSEMBLY INSTRUCTIONS

Sit N’ Sleep Bed
Assembly Instructions - Please keep for future reference
758/5418
758/5401
IMPORTANT NOTE:
The top surface of the mattress should not come above this line.
Dimensions
Width - 200cm
Height - 170.5cm
Important
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
- Please read these instructions fully before starting assembly
Issue 1 - 08/11/13
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Because of the size of this unit,
it is recommended to assemble it in the room intended for use.
• Do not discard any of the
packaging until you have checked that you have all the parts and the pack of fittings.
• Discard all extra fittings and
keep fittings out of reach of children.
Warnings
READ CAREFULLY - RETAIN FOR FUTURE REFERENCE
• Regularly check and ensure
that all bolts and fittings are tightened properly.
• Always use the ladder for
entering and leaving the upper bunk.
• The recommended mattress size is L1900 x W910 mm.
• Ensure thickness of mattress
does not exceed 220 mm.
• Refrain from using the bunk
bed if any structural part is broken or missing.
• Assemble this product on a flat
surface.
• Assemble all parts loosely before tightening any bolts.
• At least 2 people are required
to assemble this product.
• Unit weight: 38.6kgs.
• Retain Assembly Instructions
for future reference.
• Please advise your children to
only enter and leave the upper bunk by using the ladder.
• Please prohibit more that one
person on the upper bunk.
• Please prohibit children from
jumping on the upper and lower beds.
WARNING: Do not allow children under 6 years of age to use the upper bunk due to risk of injury and falls.
STRANGULATION HAZARD - Never attach or hang items such as ropes, strings, cords,
• We do not
recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
harnesses and belts to any part of the bunk bed.
WARNING: Children can become trapped between the bed and the wall. To avoid risk of serious injury the distance between the top safety barrier and the wall shall not exceed 75 mm or shall be more than 230 mm.
THIS BED COMPLIES WITH EN747-1:2012 / EN747-2:2012
Care and maintenance
• Please clean the unit surface
using either damp (not wet) cloth and a mild domestic soap solution or by using an appropriate polish.
1
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this unit.
Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Parts
Please check you have all the parts listed below
Sticker “4”Sticker “3”Sticker “2”Sticker “1”
1 Back right-hand
Front right-hand
endpost
(Ø5 x 170.5cm)
5
Upper side safety rail x 2
(91 x 36 x 4cm)
Lower rail
8
(190 x 6.5 x 2.5cm)
2
end post
(Ø5 x 170.5cm)
6
Lower side rail x 2
(91 x 4 x 2cm)
3
end post
(Ø5 x 170.5cm)
7
9
Upper back safety rail
(190 x 41.5 x 2.5cm)
4Back left-hand
Front left-hand
end post
(Ø5 x 170.5cm)
Middle side rail x 2
(89 x 2 x 2cm)
10
Upper front safety rail
(190 x 41.5 x 2.5cm)
Slats (with webbing attached) x 24
11
(94 x 2.5 x 2.6cm)
2
Components - Parts (cont.)
Please check you have all the parts listed below
Sticker “12” Sticker “13”
Left ladder side rail
12 Right ladder side rail
(Ø2.5 x 141cm)
15 Shelf side frame x 2
Ladder brace
(45.5 x 1.5 x Ø1cm)
13 Ladder step x 4
(Ø2.5 x 141cm)
16 Shelf brace x 4
(52 x 33 x 1.6cm)
14
(Ø2.5 x 29 cm)
17
(Ø1.3 x 72cm)
Small shelf panel
18 Big shelf panel
(72 x 24 x 1.2cm)
19 Back brace x 2
(72 x 33 x 1.2cm)
3
20
(135.5 x 2 x Ø1.3cm)
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 08456 400800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
M6 x 80mm Bolt x 11
D
M6 x 27mm Bolt x 12
G
Big screw x 8
J
M6 Curved washer x 19
M
M6 Lock nut x 6
P
B
M6 x 50mm Bolt x 8
E
M6 x 20mm Bolt x 11
H
Small screw x 2
K
Plastic washer x 8
N
Spring washer x 8
Q
C
M6 x 35mm Bolt x 2
F
M8 x 60 mm Bolt x 12
I
M8 Curved washer x 12
L
Wall strap x 1
O
Plastic cap x 8
Spanner x 1
Allen key x 1
Tools required
Crosshead screwdriver
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
4
Assembly Instructions
Step 1
Assembling end panels
Lay all parts flat on a soft
surface on the floor to avoid damaging any of the parts.
Note: Identify and correctly position end posts , ,
3 4
and by
1 2
looking for the sticker label pasted on the posts.
Note:
Determine your preferred shelf position. Then attach the middle side rails
7
either on the left or right.
a: b:
A J
Sticker “2” Sticker “1”
2
A J
6
2
RIGHT-HAND END PANEL
E
E
5
6
E
E
E
2
5
1
AJ
a: Attach the lower side
rail to end posts
2
and then secure using washers and
A
bolts .
Note: Do not fully tighten bolts at this stage.
16
J
b: Attach the upper side
safety rail into position and secure using bolts .
Repeat above steps to assemble the left-hand end panel as shown in the diagram.
5
E
Note: Fully
tighten all bolts using allen key .
Q
LEFT-HAND END PANEL
Sticker “4”
A J AJ
A J AJ
A J AJ
E
E
5
7
7
6
E
E
Sticker “3”
34
5
Assembly Instructions
Step 2
Attaching rails
Note: Determine your preferred bunk bed entry position. Then attach the front safety rail with
10
the entry space positioned either on the left or right.
a: Identify the correct
rails for assembly and with the help of an assistant attach the lower tubes of upper back safety rail , upper front safety rail and lower
8
rail to end posts using bolts , washers and nuts .
9
10
F
M
I
Note:
Do not fix bolts on lower holes of back safety rail at this stage.
Locate hole on
centre of lower
8
9
I
F
F
J
A
I
F
3
I
F
M
I
F
4
I
I
F
I
F
4
b:
J
10
M
M
8
A
3
9
10
hole up
c:a:
9
O
A
J
F
I
O
O
2
O
O
F
I
F
I
M
1
O
A
J
F
I
F
I
M
O
O
1
O
O
Do not fully tighten bolts at this stage.
b: Attach the top tubes
of upper back safety rail
9
and upper front safety
10
rail to end posts using bolts and washers .
Note: Do not fully tighten bolts at this stage.
c: Insert plastic caps
into holes on the right end posts & and fix by pushing firmly as shown.
1 2
JA
O
Option for
right upper bunk entry
10 10
3
4
Option for
right shelf position
2
1
3
Option for
left upper bunk entry
2
1
4
Option for
left shelf position
6
Assembly Instructions
Step 3
Attaching back braces
a: Position the back
braces as shown and attach it to upper back safety rail using bolts
F
, washers and nuts .
b: Attach the back
braces to lower rail using bolt as shown.
20
9
I
20 8
E
Note: After all bolts in step 2 and 3 are positioned, fully tighten all bolts and nuts using allen key and spanner .
Q
P
M
I
F
M
3
20
9
20
E
8
M
F
I
2
Step 4
Assembling shelf
a: Attach the shelf
braces to shelf side frames using bolts as shown.
b: Position the shelf
panels and as shown and attach it to shelf braces using screws . Tighten screws using a crosshead screwdriver.
17
16
D
Note: Do not fully tighten bolts at this stage.
18 19
17
G
a: b:
9
M
20
3
F
I
20
E
20
8
a:
16
D
D
D
17
D
17
16
17
D
17
D
D
D
b:
17
16
D
18
Note: After all bolts and screws are positioned, fully tighten all
G
18
G
17
G
17
G
G
17
bolts using allen
Q
key .
G
17
G
G
19
17
G
7
Assembly Instructions
Step 5
Attaching shelf
Position the shelf on the bed as shown and attach the side frames to middle right side rails using bolts . Tighten bolts using allen key .
16
7
D
Q
D
D
7
D
16
7
D
16
Step 6
Attaching slats
a: With the help of an
assistant, line up the
11
slats onto upper rails
9 10
and . Push firmly down to lock it into position. Check that they cannot be removed by slightly pulling upwards.
b: Extend the end of the
webbing on the slats and secure to bottom edge of side safety rails
5
using screws . Tighten screws using a crosshead screwdriver.
11
H
D
9
5
H
11
10
5
H
16
7
a: b:
11
10
11
5
H
8
Assembly Instructions
Step 7
Assembling ladder
Referring to diagram,
attach the ladder steps to ladder side rails
13
and using bolts , spring washers , curved washers and plastic washers .
12
B
N
J
K
Tighten all bolts using allen key .
Q
Note: Identify and correctly position the ladder side
12
rails and
13
by looking for the sticker labels pasted on the rails.
14
Sticker “12”
B
Sticker “13”
N
J
K
J
N
12
K
J
N
B
J
N
B
B
K
14
14
K
14
K
J
N
B
13
N
J
K
14
B
N
J
K
B
N
J
K
B
12
N
B
J
14
K
Step 8
Attaching ladder
Attach the ladder to the upper front safety rail using bolts as shown.
C
Tighten bolts using allen
Q
key .
10
10
12
C
13
C
C
10
13
9
Assembly Instructions
Step 9
Securing the ladder
Attach the ladder brace
15 12
to ladder side rail and front right-hand post
4
using bolts . Tighten bolts using allen key .
E
Q
Step 10
Fixing to wall
This unit must be fixed to a wall.
Move the bunk bed into position on the wall. Position the wall strap to the top post of upper back safety rail to
9
mark fixing holes on the
wall. Remove the wall
strap then drill holes and insert appropriate wall plugs. Reposition wall
L
strap and fix using appropriate screws.
L
4
Wall
E
15
12
12
E
L
9
15
E
Warning: Before drilling, check wall for hidden pipes and cables. Consult a qualified
L
Wall
specialist if unsure.
9
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
10
Single Metal Futon
Assembly Instructions - Please keep for future reference 7585418
7585401
Dimensions
Width - 82cm
Depth - 80-170cm
Height - 30-69.5cm
Important
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
- Please read these instructions fully before starting assembly
Issue 1 - 21/08/12
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Because of the size of this unit,
it is recommended to assemble it in the room intended for use.
• Do not discard any of the
packaging until you have checked that you have all the parts and the pack of fittings.
• Assemble this product on a flat
surface.
• Assemble all parts loosely before tightening any bolts.
Warnings
• This product should only be
used on firm, level ground.
• Make sure the legs remain in contact with the ground.
• Do not stand on the product.
• Discard all extra fittings and
keep fittings out of reach of children.
• Unit weight: 45kgs.
• At least 2 people are required
to assemble this product.
• Retain Assembly Instructions for future reference.
• Keep hands away from folding
mechanisms to prevent possible entrapment or injury.
• Do not allow children to jump
on the unit as this could cause damage to the frame.
• We do not
recommend the
use of power
drill/drivers for inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Folding and unfolding this
product should only be carried out under adult supervision.
Care and maintenance
• Please clean the unit surface using either damp (not wet)
cloth and a mild domestic soap solution or by using an appropriate polish.
• Do not use any abrasive materials when cleaning.
• From time to time check that
there are no loose bolts on this unit.
1
Components - Parts
Please check you have all the parts listed below
Futon side frame x 2
1 Front / back rail x 2
(70 x 30 x 3.2cm)
Seat frame
4 Front leg
(110 x 70 x 2cm)
2 Back frame
(76 x 8.5 x 2.5cm)
3
(70 x 55 x 2cm)
5
(63 x 26 x 2.4cm)
6 Centre leg
Flap stay
(23.5 x 1.5 x 1cm)
7 Right futon mechanism
(23 x 7.5 x 2.2cm)
8
(42.5 x 18 x 5.5cm)
Sticker “9”Sticker “8”
9Left futon mechanism
(42.5 x 18 x 5.5cm)
2
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 08456 400800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
M8 x 40mm Bolt x 8
D
M6 x 50mm Bolt x 1
G H I
M8 Lock nut x 20
J
Spacer x 2
M
Adhesive pad x 8
P
B
M8 x 30mm Bolt x 12
E F
M6 x 30 mm Bolt x 2
M6 Lock nut x 4 Curved metal washer x 8
K
Flat metal washer x 3
N
Allen key x 1
C
M6 x 60mm Bolt x 1
M6 x 15 mm Bolt x 2
L
Plastic washer x 1
O
Small spanner x 1
Big spanner x 1
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
3
Assembly Instructions
Step 1
Attaching side frames
Position the side frames
1
as shown and attach
the front/back rails
using bolts , washers and nuts . Tighten bolts
A
G
2
I
and nuts using allen key
N P
and big spanner .
Step 2
Attaching futon mechanisms
Correctly position the left
8
and right futon mechanisms and attach it to side frames using bolts and nuts .
Tighten bolts and nuts
using allen key and big spanner .
Note: Identify and correctly position the futon mechanisms and by looking for the sticker labels pasted on the rails.
9
1
B G
N
P
8
9
A
I
G
A
I
A
I
A
B
G
G
1
9
G
1
1
G
B
2
I
A
I
A
B
8
G
G
G
G
I
G
2
9
G
1
G
G
A
A
1
B
I
1
I
B
A
I
A
I
G
2
G
Step 3
Attaching back frame
Position the back frame
3
as shown and attach
it to futon mechanisms
9
and using bolts and
G
nuts . Tighten bolts and
nuts using allen key and big spanner .
P
8
B
N
B
B
B
G
3
B
G
8
G
9
G
B
B
3
G
9
G
4
Assembly Instructions
Step 4
Attaching centre leg
Carefully lay the seat
frame face down on a
4
flat protected surface. Position the centre leg
7
as shown and attach it to
seat frame using bolts .
F
Tighten bolts using allen
N
key .
Step 5
Attaching front leg
Position the front leg and attach it to seat frame using bolt , spacers and nut on
4
J H
one side then using bolt ,
washers & and nut
K L H
on the other side as
shown. Tighten bolts and
nuts using allen key and small spanner .
5
C
D
N
O
7
F
4
F
7
F
F
5
J
4
C
4
J
H
5
5
H
K
L
H
D
4
K
L
D
Step 6
Attaching flap stay
Position the flap stay
as shown and attach it to
front leg and seat frame using bolts ,
washers and nuts . Tighten bolts and nuts
using allen key and small spanner .
5
5
4
K H
N
O
H
J
J
C
H
K
E
6
6
E
5
5
H
K
4
E
E
6
K
H
Assembly Instructions
Step 7
Attaching seat frame
Position the seat frame
4
as shown and attach
it to futon mechanisms
9
and using bolts and
G
nuts . Tighten bolts and
nuts using allen key and big spanner .
P
8
B
N
B
B
9
G
B
B
B
B
8
G
G
9
G
G
4
4
G
Step 8
Attaching adhesive pads
Remove backing from
adhesive pads then carefully position it on the
top surface of front &
back rails and under the four middle rails of seat frames and back
frame as shown.
3
M
2
4
4
M
2
3
M
M
2
M
M
M
M
M
M
2
4
Assembly is complete.
6
Operation Instructions
Step 1
Folding the futon
a: Carefully pull up the
front leg and fold down
the front seat frame.
b: Fold down the front
leg.
c: Then carefully push in
the seat frame and pull up the back rest.
Step 2
Opening the futon
a: Carefully pull out the
front seat frame and fold
down the back frame.
a:
b:
c:
a: b:
b: Pull up the front leg. c: Then carefully open
the seat frame as shown.
Warning:
Keep hands away
from hinges and folding mechanisms to prevent possible entarpment or injury.
Warning:
This futon can be
used only as bed
and seat. The
recilining position
as shown on the
right is prohibited for this unit.
c:
Recilining positionSeat positionBed position
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
7
Loading...