1 Door TV Unit
Assembly Instructions - Please keep for future reference
033 xx 6002
457/1016
Dimensions
Width - 89.0cm
Depth - 38.8cm
Height - 40.0cm
GREAT BRITAIN
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
MADE IN
Rev A - 05/10/15
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Do Not dispose of packaging
until assembly complete.
Dispose of all packaging
carefully and responsibly
when assembly complete.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
From time to time check that
there are no loose screws on
this unit.
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Clean spills up immediately
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
1
If you have damaged or missing panels, call the
Components - Panels
Customer Helpline: 01709 534123
for important information when contacting Customer Helpline.
Please check you have all the panels listed below
Important - Thick lines indicate finished edges
0015
Top
(89.0x38.8cm)
0017
Left End
(38.4x38.2cm)
0018
Right End
(38.4x38.2cm)
Please turn to back page
0022
Door
(30.0x30.0cm)
0016
Bottom
(82.0x35.2cm)
0020
Plinth
(82.0x7.6cm)
0004
Small Shelf
(28.8x33.0cm)
0021
Large Shelf
(51.6x33.0cm)
0019
Divider
(29.1x35.2cm)
684xx6520
Trim x 2
(38.4x3.0 x1.2cm)
0023
Back
(30.8x30.8cm)
2
If you have damaged or missing components, call the
Components - Fittings
Customer Helpline: 01709 534123
for important information when contacting Customer Helpline.
Please turn to back page
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
A
D
G
J
Large cam x 18
Code 760001103
Panel pin x 10
Code 760001012
Fully cranked 26mm
hinge x 2
Code 652001120
Wooden dowel x 2
Code 770001006
E
H
K
B
Metal dowel x 18
Code 760003004
18mm bolt x 2
Code 700002021
Hingeplate x 2
Code 653006000
Screw x 4
Code 690001008
C
F
I
L
Shelf Support x 4
Code 681003001
Panel pin guide x 1
Code 684004501
Handle x 1
Code 644003511
45mm screw x 2
Code 690001075
Tools required
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Bradawl
Ruler - Use this ruler to help correctly identify the screws
mm
10
0
20
30
3
40
50
60
70
80
90
100
110
120
130
140
Eye protection
(when using a
hammer)
160
150
170
Exploded View
0021
0017
0015
684xx6520
0016
0020
0022
0019
0023
0004
0018
684xx6520
4
Assembly Instructions
Step 1
Fitting cams to the
bottom panel.
Insert 4 metal cams
A
into the bottom panel
.
0016
Note: Ensure cam arrow
points towards the edge
with the hole.
Step 2
Fitting cams to the
plinth panel.
A
x4
A
x4
A
A
Edged face
A
0016
A
A
A
A
Insert 4 metal cams
to the plinth panel .
A
0020
Step 3
Fitting dowels to the
top panel.
Insert 6 metal dowels
into the top panel
Note: Insert metal
dowels as far as
B
shown by arrows. Do not
over tighten.
B
0015
B
x6
A
A
0020
B
Edged face
B
B
B
B
0015
B
B
5
Assembly Instructions
Step 4
Attach dowels and
cams to both of end
panels and hinges to
the right end panel.
Insert 6 metal dowels ,
and 2 cams into the
left end panel .
A
0017
Insert 4 metal dowels ,
2 hinges and 2
cams into the right end
panel .
H
A
0018
H
B
B
B
x10
A
x4
B
B
A
0017
A
H
x2
B
B
B
B
A
B
B
B
0018
B
H
A
H
Ensure that the hinge
points towards the
grooved edge of the
panel.
Step 5
Attach dowels, cams to
both divider panels.
Insert 2 cams
and 2 wooden dowels
into the divider
panel .
0019
Turn the panel over.
Insert 2 metal dowels
into the divider panel
0019
.
A
J
B
J
x2
A
x2
Edged face
J
B
x2
A
A
0019
J
B
0019
B
6
Assembly Instructions
Step 6
Attach hinges and
handles to the doors
a: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
b: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
G
G
G
x2
A
B
K
x4
E
x2
G
G
I
x1
Correct
90
Incorrect
0022
98
Bradawl
c: Secure hinges to
doors using screws .
d: Secure handle to
doors using bolts
G
K
I
E
C
0022
K
K
K
K
0022
D
7
0022
E
E
I
Assembly Instructions
Step 7
Fitting cams to the
shelf panel.
Insert 4 metal cams
to the shelf panel .
A
0021
Step 8
Connect the left end
panel and divider panel
to the large shelf panel.
Connect the dowels in the
left end and
divider to the
cams in the shelf panel
.
0021
0017
0019
A
x4
0017
A
0021
0021
0021
A
Edged face
A
A
Edged face
9892
Turn cams 180 degrees to
lock.
Step 9
Connect the top panel
to the left end panel
and the divider panel.
Connect the dowels in the
top panel to the
dowels in the left end
panel and the
divider panel
Turn cams 180 degrees to
lock.
0015
0017
0019
0017
0021
0021
0019
Edged face
9892
0019
0015
8
Assembly Instructions
Step 10
Connect the bottom
and the plinth panel to
the left end panel.
Connect the dowels in the
left end panel to
the cams in the bottom
panel and the
plinth panel .
Ensure that dowels in
locate into bottom
0019
panel guide holes.
0016
0017
0020
0017
0016
0021
9892
Edged face
Ensure plinth sits
flush.
0020
Ensure plinth is
not overhanging.
Turn cams 180 degrees to
lock.
Step 11
Connect the right end
panel to the top,
bottom and plinth
panel.
Connect the dowels in
the top panel to
the cams in the right end
panel .
0018
0015
0019
Edged face
0020
0016
Connect the dowels in
the right end panel
to the cams in the bottom
panel and the
plinth panel .
Turn cams 180 degrees to
lock.
9
0016
0020
0018
0015
0021
9892
0018
Assembly Instructions
Step 12
Secure the bottom
panel to the divider
panels.
Using 2 screws ,
secure the bottom panel
to the divider
0016
0019
.
Now lay unit on its front
L
L
x2
0016
0021
L
L
9892
0019
Step 13
Important:
Ensure a tape
measure is used
to square up unit!
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
XX
YY
XX
DIAG 1
XX
YY
YY
XX
YY
DIAG 2
9892
XX
YY
0021
XX
YY
YY
XX
DIAG 3
YY
XX
Measure to
external corners
10
Assembly Instructions
Step 14
Attach the backpanel
Slide the back panel into
the end and top panel
grooves.
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
Ensure that the
backpanel is fully
inserted into grooves.
D
x10
F
x1
Plain chipboard surface.
D
D
YY
D
F
0021
9892
Step 15
Lay unit on its back
to attach the trims
Remove protective film
from silver trim.
Locate the notch on
the trim into the grooves
in the end panels.
To insert trims use a
hammer, place a
cardboard packing piece
between the hammer
and trims to
protect the trims.
Ensure that the trims
are inserted fully.
11
Assembly Instructions
Step 16
Fitting the shelf
supports.
Stand Unit Upright.
Insert shelf supports
into the right end
and divider panel .
Once inserted, seat the
shelf on top of the shelf
supports.
C
0018
0019
C
x4
0018
0019
Step 17
Hanging door
a: With help, slot door
hinges onto hinge plates.
Ensure screw on hinge
slides into the slot on
hingeplate.
See Diagrams 1, 2 and 3.
b: Tighten screw shown
to lock hinges in
position.
A
B
0022
See ‘Hinge adjustment’
page if the door
need adjusting.
Diagram 1
B
Ensure the underside of screw
B slides into slot on hingeplate.
Diagram 2
B
Hinge correctly attached to
hingeplate.
Diagram 3
B
Hinge incorrectly attached to
hingeplate.
12
Assembly Instructions
Step 18
Hinge adjustment
A
a: To move door up
or down: loosen screws
shown and move door
to suit.
Re-tighten screws.
b: To move door in or
out: loosen screw
shown and move door
to suit.
B
Re-tighten screw.
c: To move door left
or right: loosen or
tighten screw as shown.
Be careful not to fully
unscrew.
C
13
Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
8am - 4.30pm (Monday to Thursday)
01709 534123
(by contacting the customer service line your statutor y rights are not affected)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
8am - 2.30pm (Fridays)
You can also e-mail your requests to us at:
customer.helpdesk@addspacefl.co.uk
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
Loading...