Page 1
Mirrored Core Cabinet 1 Door
313/5226
32cm
13cm
46cm
3
Issue 2 - 06/29/20
Page 2
Page 3
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components,
call the Customer Helpline:03456 400800
12Left side panel x 1
4
Top panel x 1
3
Right side panel x 1
5 Bottom panel x 1 6 Adjustable shelf x 1
Back rail x 1
7 Back panel x 1
2
8 Door panel x 1
Page 4
Components - Fittings
Please check you have all the fittings listed below
Note:The quantities below are the correct amount to complete the assembly .In some cases more
fittings may be supplied than are required.
A
Locking pin x 4
D
Φ4 x 12mm Screw x 12
G
Wall plug(for solid wall only) x 2
J
Pad x 2
Tools
required
Phillips screwdriver
(medium & large)
B C
Locking nut x 4
E F
Wooden dowel x 12
H I
Φ4 x 45mm Screw x 2
Hinge x 2
Plastic support x 4
Cam cap x 4
Small
hammer
Flatblade screwdriver
(medium)
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
6mm Suitable drill bit
(for use with wall plug)
Hammer Drill
(Only for dril hole on the wall)
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
3
Page 5
Assembly Instructions
Step 1
Assembling side panels
NOTE:It would be useful to ask
someone to help you at this stage.
a:
Screw 4 x locking pin into left
side panel and right side panel
.
2
1
b:
Insert 6 x wooden dowel to left
side panel as shown.
1
A
E
a:
b:
1
3
4
2
A
1
Attach top panel , bottom
panel and back rail to left
5
4
3
side panel as shown.
Insert 2 x locking nut into top
B
panel and bottom panel .
Use a screwdriver to turn the
locking nut clockwise to lock.
c:
Slide down back panel along
7
grooves in bottom panel and back
rail.
Repeat above step to fix right side
panel to the unit as shown.
2
c:
B
5
1
2
B
3
E
2
7
E
B
4
Page 6
Assembly Instructions
Step 2
Assembling door panel
NOTE:It would be useful to ask
someone to help you at this stage.
a:
Use 4 x screw to fix 2 x hinge
C
onto door panel .
D
8
b:
a:
C
8
D
b:
Carefully attach door panel
8
to the unit by fixing hinge onto
side panel with 12mm screws .
D
Adjust the door up or down, left or
right, in or out if needed as shown:
1. Loosen two screws and adjust
D
the door up or down, then fix
screws again.
2. Loosen screw and adjust the
door in or out, then fix screw
again(loose screw clockwise
D
C2
C2
C1
first help to adjust door in or out if
needed).
3. Loosen screw and adjust the
door left or right, then fix screw
C1
C1
again.
4.Screw 2 x screw into the side
D
panel as shown.
D
1
D
2
8
C2
3
4
C1
D
5
Page 7
Assembly Instructions
A
Step 8
Step 3
Finishing the unit
NOTE:It would be useful to ask
someone to help you at this stage.
a:
Use 45mm screw and wall plug
G
to fix the unit on the wall as
shown.
H
a:
G
H
b:
Insert 4 x plastic support into
left side panel and right side panel.
Carefully put the adjustable shelf
on it.
6
Use 4 x cam cap to cover the
visible cams as shown.
Stick 2 x pad onto door panel
as shown.
After above assembly, please
double check and make sure all
screws are firmly fixed before use.
I
J
F
b:
F
I
6
I
J
I
NOTE:If you have damaged or missing components,
call the Customer Helpline:03456 400800
Argos LTD,489-499 Avebury Boulevard,
Central Milton Keynes, MK9 2NW
6
Page 8
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
Types of walls
No.1 “General Purpose” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
No.2 “Plasterboard” wall plug
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
No.3 “Cavity Fixing” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
For use with walls stuck with
is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
Revision 2 - 7/10/09
Loading...