2 Door 3 Drawer Sideboard
Assembly Instructions - Please keep for future reference
041 xx 6006
497/1630
Dimensions
Width - 117.2cm
Depth - 38.8cm
Height - 73.6cm
MADE IN
GREAT BRITAIN
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Rev A - 28.09.15
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Do Not dispose of packaging
until assembly complete.
Dispose of all packaging
carefully and responsibly
when assembly complete.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
From time to time check that
there are no loose screws on
this unit.
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Clean spills up immediately
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
1
Components - Panels
Please check you have all the panels listed below
Important - Thick lines indicate finished edges
622xx7000
Left drawer side x3 (30x15cm)
9990
9991
9164
Top (117.2x38.8cm)
623xx7000
Right drawer side x3 (30x15cm)
Bottom (110.2x35.2cm)
624xx7019
Drawer back x3 (32.7x15cm)
Plinth (110.2x7.6cm)
9992
Left End Panel
(72x38.2m)
9993
Right End Panel
(72x38.2cm)
9997
Shelf Panel x2
(35.5x33cm)
9996
Draw Front x3
(37.2x21cm)
684xx6530
Trim x2
(72cm long)
2601
Drawer Bottom x3
(33.8x29.8cm)
7419
Backpanel
(111.2x64.6cm)
9994
Left Divider
(62.7x35.2cm)
7293
Left Door x 2
(63.6x35.9cm)
9995
Right Divider
(62.7x35.2cm)
2
If you have damaged or missing components, call the
Components-Fittings
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly, In some case more fittings
may be supplied than are required.
M
A
D
G
J
P
Large cam x 16
Code 760001103
18mm bolt x 10
Code 700002021
Hingeplate x 4
Code 653006000
Panel Pin Locator
Code 684004501
8mm screw x 12
Code 700003510
Shelf stud x 8
Code 681003001
H
K
N
Q
B
E
Metal dowel x 28
Code 760003004
Panel pin x 14
Code 760001012
Hinge x 4
Code 652001120
Runner x 6
Code 760001040
9mm bolt x 6
Code 690001078
Panel Holder x 3
Code 680003505
C
F
I
L
O
Small cam x 12
Code 760003005
12mm screw x 8
Code 690001008
Handle x 5
Code 644003511
Assembly Screw x4
Code 690001075
Wooden dowel x 4
Code 770001006
Tools required
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Ruler - Use this ruler to help correctly identify the screws
40
50
60
70
80
90
100
3
0
mm
10
20
30
110
120
130
140
150
Drill
Bradawl
160
170
Exploded View
Please check you have all the fittings listed below
684xx6530
7293
9992
9997
9991
9994
9990
7293
9995
7419
9997
9993
622xx7000
9996
9164
624xx7019
684xx6530
2601
623xx7000
4
Assembly Instructions
Step 1
Fitting dowels to top
panel.
Insert 8 metal dowels
into the top panel
B
9990
Note: Tighten metal
dowels up fully against
the panel.
Do not over tighten.
Step 2
Fitting cams to the
bottom panel
Insert 4 cams into the
bottom panel
A
9991
B
x8
x4
B
B
B
B
B
B
9990
B
B
B
A
A
A
A
Note: Ensure cam
arrow points towards
the edge with hole.
Step 5
Step 3
Fitting cams to the
plinth panel.
Insert 4 cams into the
plinth panel
A
9164
A
x4
9991
A
A
A
A
9164
5
A
A
Assembly Instructions
Step 4
Fitting hingeplates to
the end panels.
a: Insert 2 hinges into
left end panel
b: Insert 2 hinges into
right end panel
G
9992
G
9993
Note: Ensure that the
hinge points towards the
grooved edge of the
panel.
Step 5
Fitting cams & dowels
to the end panels.
G
x4
x8
A
B
B
A
x4
G
9992
G
G
9993
G
Edge of panel
a: Insert 4 metal dowels
B
and 2 cams into
left end panel
A
9992
b: Insert 4 metal dowels
B
and 2 cams into
right end panel
A
9993
A
B
A
A
9992
B
B
B
B
B
9993
A
B
B
B
A
6
Assembly Instructions
Step 6
Attaching runners to
the division panels.
Position the runner so
that the second hole
from the front of the
runner lines up with the
pre-drilled hole nearest
to the edge of the panel.
Use screws to secure
the runner.
Front of runner
Slide the runner forward
revealing the back of the
runner. The second hole
to the back of the runner
will now line up with
the second pre-drilled
hole.
M
K
x6
M
9995
M
x12
M
M
9994
Front of Runner
M
M
M
M
M
K
Back of Runner
M
M
M
M
M
M
K
Step 7
Fitting cams and
wooden dowels to the
division panels.
a: Insert 2 wooden
dowels into the two
inner holes at the bottom
of panel . Insert
2 cams
b: Insert 2 wooden
dowels into the two
inner holes at the bottom
of panel . Insert
2 cams
O
9995
A
O
9994
A
A
x4
A
B
O
x4
O
O
9995
A
A
A
A
9994
O
O
7
Assembly Instructions
7293
Step 8
Attach hinges and
handles to 2 doors
Important:
a: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
b: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
H
H
H
x4
A
B
D
x4
F
x8
H
H
x2
I
Correct
90
H
Incorrect
7293
98
H
Bradawl
7293
H
c: Secure hinges to
doors using screws .
d: Secure handle to
doors using bolts
H
F
I
D
C
D
F
F
F
F
7293
D
7293
D
I
H
F
F
Repeat on the second
door
8
Assembly Instructions
Step 9
Drawer assembly
A: Insert small cams
into left
and right
drawer sides.
Note: Ensure cam arrow
points towards the edge
with hole.
B: Insert wooden dowels
in drawer back
624xx7019
into holes in
left
right hand
drawer sides.
622xx7000
623xx7000
622xx7000
623xx7000
C
x12
A
Left hand side
622xx7000
B
B
x12
Left hand side
622xx7000
Right hand side
623xx7000
C
C
C
C
Drawer Back
624xx7019
C: Insert 4 metal dowels
B
into the the drawer
front .
9996
9
Right hand side
623xx7000
C
B
B
B
B
9996
Assembly Instructions
Drawer assembly
continued....
D: Slide drawer bottom
into grooves in the left
and right drawer sides
and the drawer back.
E: Locate the metal
dowels (already inserted)
in the drawer front into the
small cams in the left and
right hand drawer sides.
D
Foil surface facing upwards.
Plain chipboard surface
to underside.
E
2601
SLIDE!
Ensure drawer sides are
pressed against drawer
front.
Turn cams 180 degrees to
lock.
Step 10
Fitting the handles
to drawer front.
Secure the handle with
2 bolts .
D
Repeat on all drawers.
I
D
x6
9996
I
x3
D
D
I
9996
10
Assembly Instructions
Step 11
Attach right hand end
panel, left hand
division and right
hand divsion to the top
panel
Locate cams in panels
, and
9993
onto dowels in top
panel .
Then lock.
9994
9990
A
9995
B
A
Front grooved edge
9994
9995
9993
9990
Front finished edge
Turn cam 180 degrees
to lock
Step 12
Attach bottom panel
to right hand end
panel
Locate cams in panel
onto dowels
9991
in right hand end panel
9993
.
Then lock.
A
B
A
9991
Turn cam 180 degrees
to lock
11
9993
Assembly Instructions
Step 13
Secure bottom panel
to left and right hand
divisions
Locate wooden dowels
O
already inserted in
divisions and
9994
into holes in bottom
panel .
9991
Now locate screw
through holes in bottom
panel and screw
9991
into holes in divisions
9994
. and .
9995
9995
L
L
L
x4
L
9995
L
L
L
L
9994
9991
Step 14
Attach plinth to
right hand end panel
Locate cams in panel
onto dowels
9164
in right hand end panel
9993
.
Then lock.
Turn cam 180 degrees
to lock
A
B
A
Cams to reverse
9164
9993
12
Assembly Instructions
Step 15
Attach left hand end
to top, bottom and
plinth
Locate cams in panel
onto dowels
9992
in top panel .
Then lock.
Locate dowels in
left hand end panel
9992
into cams
in bottom and
9164
plinth .
Then lock.
A
9990
9991
B
B
A
9164
9991
9992
A
Turn cam 180 degrees
to lock
Step 16
Locate backpanel
into grooves in left
and right hand end
panels and top panel
Important:
2 people required
Important:
You do not have
to turn your
unit round it is
shown this way
just to show how
backpanel is
located.
9990
7419
Plain chipboard
surface
9993
9990
9992
Locate backpanel
into grooves in left hand
9992
end and right hand
9993
end slide the
backpanel into
groove in top .
13
7419
7419
9990
Assembly Instructions
Step 17
Lay unit down to
square unit up
Warning:
2 people to lift.
Lift with care.
YY
XX
Measure to external corners
DIAG 1
XX
9160
7397
Important:
Ensure a tape measure
is used to square up
unit!
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
Step 18
Secure backpanel
to bottom panel.
XX
XX
XX
YY
YY
DIAG 2
YY
YY
XX
XX
YY
9161
DIAG 3
YY
Fittings you will need for this step:
F
(x1)
E
(x14)
YY
XX
Secure backpanel
to bottom panel and
divisions using panel
E
pins .
Use the panel pin guide
F
when locating the
panel pins . This will
E
hold the panel pins
vertical and ensure the
correct distance from the
edge. You cannot use
panel pin guide when
securing backpanel to
divisions.
E
F
7419
7398
E
365mm
50mm
E
50mm
7419
365mm
E
7398
14
Assembly Instructions
Step 19
Add stability blocks.
Slide the thin point of the
stability blocks
between the back panel
and the grooves.
7419
Once inserted fully,
tighten the screws in the
stability blocks.
Q
Q
x3
Q
Q
7419
Q
Q
Step 20
Attach silver trim
Turn unit over.
Remove protective film
from silver trim.
Warning:
2 people to lift.
Lift with care.
Locate the notch on
silver trim into
groove on left and
9993
right ends.
Ensure the silver
trims are positioned
correctly.
To insert silver trims
use a hammer, place a
cardboard packing piece
between the hammer
and silver trims to
protect the silver
trims.
9992
Fittings you will need for this step:
Silver Trims
(x2)
9992
9993
15
Assembly Instructions
Step 21
Lift unit up and
locate drawers
Warning:
2 people to lift.
Lift with care.
For this step we
recommend you follow
the helpful hints page.
N
(x6)
Detailed View
N
2nd Hole
16
Assembly Instructions
Step 21.....cont
Locate drawers helpful
hints
a: Pull sliding part of
drawer runners out
so they are fully
extended.
K
b: Locate drawer onto
runners.
c: Locate screwdriver
into second threaded
L
hole in drawer runner .
K
d: Keeping screwdriver
in place push the drawer
in until the screwdriver
pushes against the
panel.
Remove the screwdriver.
A
C
B
K
L
L
K
D
J
K
L
2nd Hole
e/f: Pull drawer out slowly
and line the front hole in the
drawer side with the 2nd
threaded hole in runner .
Holding runner and
drawer side together
insert bolts through the
drawer side and
into threaded hole in
runner .
Now repeat these
steps for the other
side of the drawer.
17
N
J
L
K
K
E
F
H
N
J
2nd Hole
Assembly Instructions
Step 22
Locate shelf studs
Push shelf studs
into panels , ,
9994
and .
9992
9995
P
9993
P
P
x8
P
9992
9995
P
9993
Step 23
Locate shelves onto
shelf studs
Locate shelves
onto shelf studs
9997
P
9997
9997
18
Assembly Instructions
Step 24
Hanging doors
a: With help, slot door
hinges onto hinge
plates .
Ensure screw on hinge
H
slides into the slot
on hingeplate .
See Diagrams 1,2 and 3.
H
G
G
b: Tighten screw shown
to lock hinges in
position.
Repeat a and b for
opposite door.
See ‘Hinge adjustment’
in step 25 if the doors
need adjusting.
7293
a:
G
H
G
H
9993
H
G
G
b:
H
Underside view
Diagram 1
Diagram 2
Diagram 3
B
Ensure the underside of screw
B slides into slot on hingeplate.
B
Hinge correctly attached to
hingeplate.
B
19
Hinge incorrectly attached to
hingeplate.
Assembly Instructions
Step 25
Hinge adjustment
a:
a: To move doors up
or down: loosen screws
shown and move doors
to suit.
Re-tighten screws.
b: To move doors in or
out: loosen screw
shown and move doors
to suit.
Re-tighten screws.
G
H
b:
G
c: To move doors left
or right: loosen or
tighten screw as shown.
Be careful not to fully
unscrew.
G
c:
G
H
20
Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
8am - 4.30pm (Monday to Thursday)
01709 534123
(by contacting the customer service line your statutory rights are not affected)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
8am - 2.30pm (Fridays)
You can also e-mail your requests to us at:
customer.helpdesk@addspacefl.co.uk
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
Loading...