Argos 2749840 ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 39.5cm

Depth - 40cm

Height - 39cm

New Sywell - 2 Drawer Bedside

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 11/03/15

Important - Please read these instructions fully before starting assembly

282/8417

281/2612

279/9618

268/4792

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 10kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).

• Dispose of all packaging
carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels

Please check you have all the panels listed below

2

1

2 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

4

Top (D2541A)

(363 x 394mm)

Back (X389-359)

(389 x 359mm)

Left Side (D2542A)

(388 x 396mm)

Right Side (D2543A)

(388 x 396mm)

Rail (D2544A)

(363 x 78mm) x 2

5

Drawer Front (D2545A)

(359 x 162mm) x 2

Drawer Base (T342-367)

(342 x 367mm) x 2

9 10

7

Drawer Back (W330-124)

(330 x 124mm) x 2

8

6

Left Drawer Side (W370-124LH)

(370 x 124mm) x 2

Right Drawer Side (W370-124RH)

(370 x 124mm) x 2

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

A

Wooden dowel (F22) x 6

B

Metal dowel (F901) x 12

C

D E F

G H I

Rule Scissors Hammer

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J K

9mm Screw (F74) x 4 9mm Screw (F73) x 8

Drawer runner (F1004) x 4

Electric drill
(do not use for
fitting screws)

Knock-in Peg (F171) x 8

Small locking
nut (F3) x 4

Large locking
nut (F900) x 8

Nail (F51) x 10

Handle (F315) x 2

25mm Screw (F95) x 4

M

Plastic Nail (F91) x 4

L

Wedgefix (F639) x 4

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 2

x 2 x 2

x 2

B

Prepare the drawer
fronts

Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .

Note: Tighten the metal
dowels up fully against
the panels.

B

5

Prepare the drawer
sides

Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .

Note: Arrow on locking
nut must point towards
hole in edge of panel.

E

7

8

Step 2

Step 3

B

B

5

Attach the drawer
sides to the drawer
front

Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .

Turn the small locking
nuts on the left
drawer side and right
drawer side .

Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.

7
8

5

E

7
8

Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.

E

5

E

B

B

E

Small groove

9

Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.

E

E

7

8

8

7

9

8

5

7

6

Assembly Instructions

5

Step 4

Step 5

Fit the drawer base

Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .

9

7 8

5

C

C

x 2

Fit the drawer back

Fit the drawer back
down onto the drawer
base .

Make sure that the
drawer base fits into
the groove in the drawer
back .

Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .

6

9

9

6

6

C

7 8

C

C

Attach the handle

Attach a handle to
each drawer front
using 2 screws .

J

F

Step 6

5

x 2

5

F

F

J

x 2

Step 7

Fit the wedgefixes

Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.

L

L

L

L

I

x 2

9

8

7

5

Finished front edge

Assembly Instructions

6

Step 7

Prepare the left side

a: Place 2 runners on

the left side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

Screw 4 metal dowels
into the left side .

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .

K

1

Finished

front edge

H

K

H

K

B

B

B

H

K

B

H

H

H

Finished front edge

1

1

a:

a:

b:

b:

B

1

K

H

1

Finished

front edge

Finished

front edge

H

K

H

K

H

K

B

B

B

B

H

H

Step 8

Prepare the right side

a: Place 2 runners on

the right side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

Screw 4 metal dowels
into the right side .

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .

K

2

H

B

2

K

H

2

2

2

Finished

front edge

Finished

front edge

A

Assembly Instructions

7

Step 9

Prepare the top

Tap 2 wooden dowels
into the top .

Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.

Insert 4 large locking
nuts into the
top .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

Fit the top to the right
side

Push the top onto
the right side .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

Step 10

Step 11

D

D

D

D

D

A

10mm

A

A

3

D

3

3

plain chipboard surface

Finished

front edge

3

2

D

3

D

B

D

Prepare the 2 rails

Tap 2 wooden dowels
into each of the 2 rails .

Insert 2 large locking
nuts into each of the
2 rails .

A

4

D

4

x 2

2

plain chipboard surface

3

A

A

plain chipboard surface

4

D

D

Assembly Instructions

8

Step 12

Step 13

Fit the left side

Push the left side
onto the assembly.

Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the top and the 2
rails .

D

1

3

4

Fit the 2 rails

Push the 2 rails onto
the right side .

Use a screwdriver to
tighten the large locking
nut fitted to each of
the 2 rails .

D

4

2

4

2

4

4

Note: Support this
rail until the left
side has been fitted
in the next step.

4

4

3

1

Assembly Instructions

9

Step 14

b:

Fit the back and
plastic nails

a: Square up the unit by

making sure that
measurement x to x

equals y to y.

b: Place the back

onto the unit.
Nail around the
outside edges of the
back .

Note: Nails should be
spaced about 150mm
apart.

10

I

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

10

Fit the drawers

Starting with the bottom
drawer, slide both the
runners forward and
locate the drawer sides
. and between
them, lining up the holes
in the drawer wrap with
the 2nd 'threaded' holes
in the runners .

Working from the inside
of the drawer, insert 2
screws through the
sides and out into the
2nd threaded hole in the
runner.

Note: Do not over­tighten the screws .
If they catch on the
runner you may need
to loosen them slightly.

G

7 8

K

K

G

Step 15

G

G

2nd threaded

hole

K

G

7

8

y

y

x

x

I

10

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

M

1

2

Stand the unit up
for the next step.

M

2

1

M

M

M

Assembly Instructions

10

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Step 16

Assembly is complete

ALR3011

MADE IN

BRITAIN

Dimensions

Width - 104cm

Depth - 49.5cm

Height - 171cm

New Sywell - 4 Drawer 3 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 07/10/14

Important - Please read these instructions fully before starting assembly

282/7023

258/1376

281/6096

278/9130

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 73kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 1, 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.

• Dispose of all packaging
carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

1 4

5

3

7

2

6

8

1

Drawer Front (D2575A)

(333 x 162mm) x 4

Drawer Base (T315-367)

(315 x 367mm) x 4

Drawer Back (W304-124)

(304 x 124mm) x 4

Left Drawer Side (W370-124LH)

(370 x 124mm) x 4

Right Drawer Side (W370-124RH)

(370 x 124mm) x 4

Rail (D2598A)

(322 x 125mm)

Horizontal (D2573A)

(337 x 467mm)

Shelf (D2574A)

(322 x 468mm) x 3

Components - Panels

Please check you have all the panels listed below

2

9

10

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D2560A)

(1711 x 496mm)

Right Side (D2569A)

(1711 x 496mm)

Hanging Rail (FHR666)

(666mm long)

12

Top (D2568A)

(1011 x 494mm)

Base (D2570A)

(1011 x 494mm)

Upright (D2571A)

(1656 x 468mm)

Large Door (D2563A)

(1650 x 333mm) x 2

Centre Door (D2576A)

(990 x 333mm)

Small Back (X1682-340)

(1682 x 340mm)

Large Back (X1682-694)

(1682 x 694mm)

11

13

14

15

Divider (D2572A)

(675 x 468mm)

17

16

18 19

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A

Wooden dowel (F22) x 20

B

Metal dowel (F901) x 28

C

D E F

G H I

L

M

J K

9mm Screw (F74) x 8 9mm Screw (F73) x 16

P

Drawer runner (F1004) x 8

13mm Screw (F79) x 1

Small locking
nut (F3) x 8

Large locking
nut (F900) x 20

Nail (F51) x 37

Bracket (F327) x 1

Handle (F315) x 7

13mm Screw (F63) x 20

ON

Hinge plate

(F523) x 8

Hinge (F522) x 8

Q

25mm Screw (F95) x 14

R

Rail Holder
(F891) x 2

S

Nail screw (F277) x 5

Shelf stud (F110) x 12

V

Foot (F854) x 1

25mm Screw (F50) x 1

Knock-in Peg (F171) x 16

U X

Plastic Nail (F91) x 4

W

Wedgefix (F639) x 8

T

Back holder (F276) x 5

These can

also be round

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 4 x 4

x 4

B

Prepare the 4 drawer
fronts

Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .

Note: Tighten the metal
dowels up fully against
the panels.

B

1

Prepare the drawer
sides

Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .

Note: Arrow on locking
nut must point towards
hole in edge of panel.

E

4

5

Step 2

Step 3

B

B

1

Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.

Attach the drawer
sides to the drawer
front

Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .

Turn the small locking
nuts on the left
drawer side and right
drawer side .

Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.

4
5

1

E

4
5

x 4

E

Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.

E

B

B

E

Small groove

9

E

E

4

5

5

1

4

Assembly Instructions

5

Step 4

Step 5

Fit the drawer base

Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .

3

4 5

1

Fit the drawer back

Fit the drawer back
down onto the drawer
base .

Make sure that the
drawer base fits into
the groove in the drawer
back .

Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .

2

3

3

2

2

U

4 5

Attach the handles

Attach a handle to
each drawer front
using 2 screws .

L

F

Step 6

1

3

5

4

2

U

U

x 4

U

U

x 4

1

F

F

L

x 4

Step 7

Fit the wedgefixes

Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.

W

W

W

W

I

x 4

3

5

4

1

A

A

Assembly Instructions

6

Step 8

Prepare the upright

a: Place 4 runners on

the upright . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the upright . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the upright .

Fit 2 hinge plates onto
the upright , making
sure that the slot is
facing towards the
finished front edge.

c: Tap 4 wooden

dowels into the
upright .

Screw 2 metal dowels
into the upright .

Insert 4 large locking
nuts into the
upright .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

P

11

I

R

J

11

P

P

P

P

I

I

I

I

I

I

I

I

B

B

D

D

D

D

N

N

N

J

R

J

A

A

J

R

J

R

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

I

P

a:

b:

c:

J

P

11

11

I

11

11

11

N

A

11

11

11

10mm

A

D

B

D

Finished

front edge

Finished

front edge

Assembly Instructions

7

Step 9

Finished

front edge

I

P

I

P

I

P

I

P

I

P

I

I

I

I

B

D

B

D

B

A

A

Prepare the divider

a: Place 4 runners on

the divider . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the divider .

c: Tap 2 wooden

dowels into the
divider .

Screw 2 metal dowels
into the divider .

Insert 2 large locking
nuts into the
divider .

Turn the divider over

d: Screw a metal dowel

. into the divider .

P

15

I

P

15

15

15

I

Turn the divider over

A

B

D

15

Finished

front edge

Finished

front edge

15

B

a:

b:

c:

d:

15

15

15

15

Finished

front edge

Assembly Instructions

8

Step 10

A

A

Finished

front edge

Plain chipboard

surface

D

D

D

D

A

A

Prepare the horizontal

Tap 4 wooden dowels
into the horizontal .

Insert 4 large locking
nuts into the
horizontal .

A

8

D

8

8

Finished

front edge

Finished

front edge

Step 11

Fit the horizontal to
the upright

Push the horizontal
onto the upright .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

Step 12

Fit the divider to the
horizontal

Push the divider onto
the horizontal .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .

8

11

11

D

15

8

8

D

D

B

D

8

11

8

15

Finished

front edge

Assembly Instructions

9

Step 13

Step 14

A

A

Prepare the base

a: Tap 4 wooden

dowels into the base
. .

Insert 4 large locking
nuts into the base .

Screw the foot into
the middle of the base ,
75mm in from the front
edge using screw .

Turn the base over

b: Screw 4 metal

dowels into the base
. .

A

14

D

14

D

D

C

V

A

A

Finished

front edge

75mm

D

D

Plain chipboard

surface

14

Finished

front edge

B

B

B

B

14

Turn the

base over

a:

b:

14

B

Fit the base

Push the base onto
the upright and
divider .

Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the upright and the
divider .

14

11

D

14

15

11

15

11

15

Note: To make it
easier to fit the top
and base panels, place
polystyrene blocks
from the packaging
underneath the upright
and divider panels to
raise the assembly.

V

14

C

Finished

front edge

Assembly Instructions

10

Step 15

Finished

front edge

A

A

D

D

A

A

D

D

B

B

Prepare the top

a: Tap 4 wooden

dowels into the top .

Insert 4 large locking
nuts into the top .

Screw 2 metal dowels
into the top .

A

13

D

13

13

B

13

Step 16

Fit the top

Push the top onto
the upright .

Use a screwdriver to
tighten the 2 large
locking nuts fitted
to the upright .

13

11

D

11

13

11

Step 17

B

B

B

B

N

N

N

Finished

front edge

Prepare the right side

Screw 4 metal dowels
into the right side .

Fit 3 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.

B

10

N

10

10

N

Assembly Instructions

11

Step 18

Fit the right side

Push the right side
onto the top and
base .

Use a screwdriver to
tighten the 4 large
locking nuts fitted
to the top and
base .

Step 19

Finished

front edge

Prepare the left side

Screw 5 metal dowels
into the left side .

Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.

To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

B

9

N

N

N

N

B

B

B

B

B

J

R

J

9

N

9

R

J

9

J

13

10

14

10

13

14

D

13

14

A

Assembly Instructions

12

Step 20

Prepare the rail

Tap 2 wooden dowels
into the rail .

Insert 2 large locking
nuts into the rail .

Step 21

D

A

D

Plain chipboard

surface

6

A

D

6

6

Fit the rail

Push the rail onto the
divider .

Use a screwdriver to
tighten the large locking
nut fitted to the rail .

6

6

15

D

6

15

Note: Support the
rail until the left
side has been fitted
in the next step.

yxy

yy

Assembly Instructions

13

Step 22

Step 23

13

14

Finished

front edge

9

6

Fit the left side

Push the left side
onto the assembly.

Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the top , base
and rail .

9

D

13 14

6

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

Fit the back panels

a: Square up the unit by

making sure that
measurement x:x equals

y:y.

Place the small back
and large back down
onto the unit as shown.

Make sure that the 2
backs are pushed up
tight against each other
and that they meet over
the back edge
of the upright.

b: Nail around

the outside
edges
of the 2 backs.

Note: Do not
nail where the
backs meet.
Nails should be
spaced about
150mm apart.

18

19

M

Note: Do not
nail where the
backs meet.

b:

M

18

19

x

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

X

9

10

9

X

X

10

X

X

Assembly Instructions

14

Step 24

Step 25

18

19

Secure the backs

Tap the nail screws
through the back holders
. and down between
the backs and
into the back edge
of the divider.

Keep tapping the
nail screws in
until the back
holders dig
into the small
and large back.

Stand the unit up
for the next step.

S

T

18 19

S

T

TS

+

x 5

Warning: The
unit is heavy.
Lift with care.

Fit the hanging rail
and the drawers

Starting with the bottom
drawer, slide both the
runners forward and
locate the drawer
sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .

Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.

Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.

H

P

P

4 5

H

2nd threaded

hole

P

H

H

H

S

T

T

Note: These can
also be round

Assembly Instructions

15

Step 26

Step 27

Q

x 4

Q

x 4

Q

x 4

Fit the shelf studs

For each of the 3
shelves , insert 4 shelf
studs at the desired
height.

Q

7

Fit the shelves

Lower the 3 shelves
down onto the shelf
studs .

Q

7

7

7

7

Assembly Instructions

16

Step 28

12

12

R

Fit the hanging rail

Push the hanging rail
into the rail holders
fitted to the side panels.

12

R

Step 29

Prepare the 3 doors

Push fit 3 hinges into
the centre door and
each of the large doors
. .

Secure each hinge with
2 screws .

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.

J

O

16

17

90

O

O

J

J

O

J

J

O

J

J

17

x 2

O

J

J

O

J

J

16

L

17

Assembly Instructions

17

Step 30

Fit doors and handles

Note: The easiest way to
attach each door and
. is to fit the top hinge
first, then align and fit the
other hinges.

a: Push the hinge

onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.

b: Keep the hinge

FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.

c: The hinge must be

flat against the hinge
plate prior to any
adjustment.

d: The hinge must

NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.

e: Attach a handle to

each door and
using 2 screws .

O

O

O

N

N

N

O

N

L

F

16

17

16 17

a: b:

c: d:

N

O

N

N

B

N

O

O

O

A

O

N

B

e:

F

F

17

16

L

L

Assembly Instructions

18

Step 31

b:

c:

d:

a:

Adjust the doors if
needed

a: Before adjusting the

doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.

b: Height adjustment.

Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.

c: Forward and Back

adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.

d: Sideways

adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.

A

A

B

C

Assembly Instructions

19

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

ALR3014

Step 32

Top of Unit

WALL

WALL

Back of Unit

Fit the bracket

To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the
bracket fitted to the
top of the unit.

Fixings are not supplied,
as they will need to suit
the wall type and the
length of screw will
depend on the distance
from the back of the unit
to the wall.

Fix the bracket
loosely onto the top of
the unit using screw
and mark the wall for the
wall fixing.

Swivel the bracket
away from the wall and
drill a hole in the wall
using a suitable drill bit
and fit your wall fixing.

Swivel the bracket
back and fix the bracket
to the wall, then tighten
screw .

Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.

Warning: The
unit is heavy.
Lift with care.

Assembly is complete

K

K

G

K

K

G

K

K

G

K

MADE IN

BRITAIN

Dimensions

Width - 104cm

Depth - 49.5cm

Height - 171cm

New Sywell - 4 Drawer 3 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 5 - 13/01/15

Important - Please read these instructions fully before starting assembly

282/7023

258/1376

281/6096

278/9130

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 73kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 1, 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.

• Dispose of all packaging
carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

1 4

5

3

7

2

6

8

1

Drawer Front (D2575A)

(333 x 162mm) x 4

Drawer Base (T315-367)

(315 x 367mm) x 4

Drawer Back (W304-124)

(304 x 124mm) x 4

Left Drawer Side (W370-124LH)

(370 x 124mm) x 4

Right Drawer Side (W370-124RH)

(370 x 124mm) x 4

Rail (D2598A)

(322 x 125mm)

Horizontal (D2573A)

(337 x 467mm)

Shelf (D2574A)

(322 x 468mm) x 3

Components - Panels

Please check you have all the panels listed below

2

9

10

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Left Side (D2560A)

(1711 x 496mm)

Right Side (D2569A)

(1711 x 496mm)

Hanging Rail (FHR666)

(666mm long)

12

Top (D2568A)

(1011 x 494mm)

Base (D2570A)

(1011 x 494mm)

Upright (D2571A)

(1656 x 468mm)

Large Door (D2563A)

(1650 x 333mm) x 2

Centre Door (D2576A)

(990 x 333mm)

Small Back (X1682-340)

(1682 x 340mm)

Large Back (X1682-694)

(1682 x 694mm)

11

13

14

15

Divider (D2572A)

(675 x 468mm)

17

16

18 19

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A

Wooden dowel (F22) x 20

B

Metal dowel (F901) x 28

C

D E F

G H I

L

M

J K

9mm Screw (F74) x 8 9mm Screw (F73) x 16

P

Drawer runner (F1004) x 8

Small locking
nut (F3) x 8

Large locking
nut (F900) x 20

Nail (F51) x 37

Handle (F315) x 7

13mm Screw (F63) x 20

ON

Hinge plate

(F523) x 8

Hinge (F522) x 8

Q

25mm Screw (F95) x 14

R

Rail Holder
(F891) x 2

S

Nail screw (F277) x 5

Shelf stud (F110) x 12

V

Foot (F854) x 1

25mm Screw (F50) x 1

Knock-in Peg (F171) x 16

U

Plastic Nail (F91) x 4

W

Wedgefix (F639) x 8

T

Back holder (F276) x 5

These can

also be round

Strap Screw

Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

x 4 x 4

x 4

B

Prepare the 4 drawer
fronts

Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .

Note: Tighten the metal
dowels up fully against
the panels.

B

1

Prepare the drawer
sides

Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .

Note: Arrow on locking
nut must point towards
hole in edge of panel.

E

4

5

Step 2

Step 3

B

B

1

Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.

Attach the drawer
sides to the drawer
front

Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .

Turn the small locking
nuts on the left
drawer side and right
drawer side .

Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.

4
5

1

E

4
5

x 4

E

Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.

E

B

B

E

Small groove

9

E

E

4

5

5

1

4

Assembly Instructions

5

Step 4

Step 5

Fit the drawer base

Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .

3

4 5

1

Fit the drawer back

Fit the drawer back
down onto the drawer
base .

Make sure that the
drawer base fits into
the groove in the drawer
back .

Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .

2

3

3

2

2

U

4 5

Attach the handles

Attach a handle to
each drawer front
using 2 screws .

L

F

Step 6

1

3

5

4

2

U

U

x 4

U

U

x 4

1

F

F

L

x 4

Step 7

Fit the wedgefixes

Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.

G

G

G

G

I

x 4

3

5

4

1

A

A

Assembly Instructions

6

Step 8

Prepare the upright

a: Place 4 runners on

the upright . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the upright . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the upright .

Fit 2 hinge plates onto
the upright , making
sure that the slot is
facing towards the
finished front edge.

c: Tap 4 wooden

dowels into the
upright .

Screw 2 metal dowels
into the upright .

Insert 4 large locking
nuts into the
upright .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

P

11

I

R

J

11

P

P

P

P

I

I

I

I

I

I

I

I

B

B

D

D

D

D

N

N

N

J

R

J

A

A

J

R

J

R

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

I

P

a:

b:

c:

J

P

11

11

I

11

11

11

N

A

11

11

11

10mm

A

D

B

D

Finished

front edge

Finished

front edge

Assembly Instructions

7

Step 9

Finished

front edge

I

P

I

P

I

P

I

P

I

P

I

I

I

I

B

D

B

D

B

A

A

Prepare the divider

a: Place 4 runners on

the divider . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the divider .

c: Tap 2 wooden

dowels into the
divider .

Screw 2 metal dowels
into the divider .

Insert 2 large locking
nuts into the
divider .

Turn the divider over

d: Screw a metal dowel

. into the divider .

P

15

I

P

15

15

15

I

Turn the divider over

A

B

D

15

Finished

front edge

Finished

front edge

15

B

a:

b:

c:

d:

15

15

15

15

Finished

front edge

Assembly Instructions

8

Step 10

A

A

Finished

front edge

Plain chipboard

surface

D

D

D

D

A

A

Prepare the horizontal

Tap 4 wooden dowels
into the horizontal .

Insert 4 large locking
nuts into the
horizontal .

A

8

D

8

8

Finished

front edge

Finished

front edge

Step 11

Fit the horizontal to
the upright

Push the horizontal
onto the upright .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

Step 12

Fit the divider to the
horizontal

Push the divider onto
the horizontal .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .

8

11

11

D

15

8

8

D

D

B

D

8

11

8

15

Finished

front edge

Assembly Instructions

9

Step 13

Step 14

A

A

Prepare the base

a: Tap 4 wooden

dowels into the base
. .

Insert 4 large locking
nuts into the base .

Screw the foot into
the middle of the base ,
75mm in from the front
edge using screw .

Turn the base over

b: Screw 4 metal

dowels into the base
. .

A

14

D

14

D

D

C

V

A

A

Finished

front edge

75mm

D

D

Plain chipboard

surface

14

Finished

front edge

B

B

B

B

14

Turn the

base over

a:

b:

14

B

Fit the base

Push the base onto
the upright and
divider .

Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the upright and the
divider .

14

11

D

14

15

11

15

11

15

Note: To make it
easier to fit the top
and base panels, place
polystyrene blocks
from the packaging
underneath the upright
and divider panels to
raise the assembly.

V

14

C

Finished

front edge

Assembly Instructions

10

Step 15

Finished

front edge

A

A

D

D

A

A

D

D

B

B

Prepare the top

a: Tap 4 wooden

dowels into the top .

Insert 4 large locking
nuts into the top .

Screw 2 metal dowels
into the top .

A

13

D

13

13

B

13

Step 16

Fit the top

Push the top onto
the upright .

Use a screwdriver to
tighten the 2 large
locking nuts fitted
to the upright .

13

11

D

11

13

11

Step 17

B

B

B

B

N

N

N

Finished

front edge

Prepare the right side

Screw 4 metal dowels
into the right side .

Fit 3 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.

B

10

N

10

10

N

Assembly Instructions

11

Step 18

Fit the right side

Push the right side
onto the top and
base .

Use a screwdriver to
tighten the 4 large
locking nuts fitted
to the top and
base .

Step 19

Finished

front edge

Prepare the left side

Screw 5 metal dowels
into the left side .

Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.

To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.

B

9

N

N

N

N

B

B

B

B

B

J

R

J

9

N

9

R

J

9

J

13

10

14

10

13

14

D

13

14

A

Assembly Instructions

12

Step 20

Prepare the rail

Tap 2 wooden dowels
into the rail .

Insert 2 large locking
nuts into the rail .

Step 21

D

A

D

Plain chipboard

surface

6

A

D

6

6

Fit the rail

Push the rail onto the
divider .

Use a screwdriver to
tighten the large locking
nut fitted to the rail .

6

6

15

D

6

15

Note: Support the
rail until the left
side has been fitted
in the next step.

yxy

yy

Assembly Instructions

13

Step 22

Step 23

13

14

Finished

front edge

9

6

Fit the left side

Push the left side
onto the assembly.

Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the top , base
and rail .

9

D

13 14

6

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

Fit the back panels

a: Square up the unit by

making sure that
measurement x:x equals

y:y.

Place the small back
and large back down
onto the unit as shown.

Make sure that the 2
backs are pushed up
tight against each other
and that they meet over
the back edge
of the upright.

b: Nail around

the outside
edges
of the 2 backs.

Note: Do not
nail where the
backs meet.
Nails should be
spaced about
150mm apart.

18

19

M

Note: Do not
nail where the
backs meet.

b:

M

18

19

x

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

K

9

10

9

K

K

10

K

K

Assembly Instructions

14

Step 24

Step 25

18

19

Secure the backs

Tap the nail screws
through the back holders
. and down between
the backs and
into the back edge
of the divider.

Keep tapping the
nail screws in
until the back
holders dig
into the small
and large back.

Stand the unit up
for the next step.

S

T

18 19

S

T

TS

+

x 5

Warning: The
unit is heavy.
Lift with care.

Fit the hanging rail
and the drawers

Starting with the bottom
drawer, slide both the
runners forward and
locate the drawer
sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .

Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.

Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.

H

P

P

4 5

H

2nd threaded

hole

P

H

H

H

S

T

T

Note: These can
also be round

Assembly Instructions

15

Step 26

Step 27

Q

x 4

Q

x 4

Q

x 4

Fit the shelf studs

For each of the 3
shelves , insert 4 shelf
studs at the desired
height.

Q

7

Fit the shelves

Lower the 3 shelves
down onto the shelf
studs .

Q

7

7

7

7

Assembly Instructions

16

Step 28

12

12

R

Fit the hanging rail

Push the hanging rail
into the rail holders
fitted to the side panels.

12

R

Step 29

Prepare the 3 doors

Push fit 3 hinges into
the centre door and
each of the large doors
. .

Secure each hinge with
2 screws .

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.

J

O

16

17

90

O

O

J

J

O

J

J

O

J

J

17

x 2

O

J

J

O

J

J

16

L

17

Assembly Instructions

17

Step 30

Fit doors and handles

Note: The easiest way to
attach each door and
. is to fit the top hinge
first, then align and fit the
other hinges.

a: Push the hinge

onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.

b: Keep the hinge

FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.

c: The hinge must be

flat against the hinge
plate prior to any
adjustment.

d: The hinge must

NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.

e: Attach a handle to

each door and
using 2 screws .

O

O

O

N

N

N

O

N

L

F

16

17

16 17

a: b:

c: d:

N

O

N

N

B

N

O

O

O

A

O

N

B

e:

F

F

17

16

L

L

Assembly Instructions

18

Step 31

b:

c:

d:

a:

Adjust the doors if
needed

a: Before adjusting the

doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.

b: Height adjustment.

Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.

c: Forward and Back

adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.

d: Sideways

adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.

A

A

B

C

Assembly Instructions

19

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

ALR3014

Step 32

Fit the overbalance
protector kit

To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an
alternative fixing method
of your choice.

Wall fixings are not
supplied as they will
need to suit the wall
type.

Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.

Assembly is complete

W

W

WALL

Wall fixing

(not supplied)

Screw

(not supplied)

Washer

Strap

W

Strap

Washer

Screw

TOP OF UNIT

W

MADE IN

BRITAIN

Dimensions

Width - 69cm

Depth - 40cm

Height - 88.5cm

New Sywell - 5 Drawer Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 3 - 08/04/14

Important - Please read these instructions fully before starting assembly

257/7579

280/5935

282/2248

280/2110

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 28.5kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.

• Dispose of all packaging
carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Top (D2546A)

(658 x 394mm)

Drawer Front (D2550A)

(654 x 162mm) x 5

2

Rail (D2549A)

(658 x 78mm) x 3

3

4

5

10

Back (X684-524)

(854 x 684mm)

Left Side (D2552A)

(883 x 396mm)

Right Side (D2555A)

(883 x 396mm)

Drawer Base (T636-327)

(636 x 367mm) x 5

Drawer Back (W625-124)

(625 x 124mm) x 5

9

6

7 8

Left Drawer Side (W370-124LH)

(370 x 124mm) x 5

Right Drawer Side (W370-124RH)

(370 x 124mm) x 5

6

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

A

Wooden dowel (F22) x 8

B

Metal dowel (F901) x 20

C

D E F

G H I

L

Rule Scissors Hammer

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

M

J K

9mm Screw (F74) x 10 9mm Screw (F73) x 20

Drawer runner (F1004) x 10

Electric drill
(do not use for
fitting screws)

Knock-in Peg (F171) x 20

13mm Screw (F79) x 1

Small locking
nut (F3) x 10

Large locking
nut (F900) x 10

Nail (F51) x 21 Bracket (F327) x 1

Handle (F315) x 5

25mm Screw (F95) x 10

O

Plastic Nail (F91) x 4

N

Wedgefix (F639) x 20

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 5

B

Prepare the drawer
fronts

Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .

Note: Tighten the metal
dowels up fully against
the panels.

B

5

Prepare the drawer
sides

Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .

Note: Arrow on locking
nut must point towards
hole in edge of panel.

E

7

8

Step 2

Step 3

B

B

5

Attach the drawer
sides to the drawer
front

Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .

Turn the small locking
nuts on the left
drawer side and right
drawer side .

Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.

7
8

5

E

7
8

E

x 5 x 5

x 5

Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.

E

B

B

E

Small groove

9

Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.

E

E

7

8

8

7

5

Assembly Instructions

5

Step 4

Step 5

Fit the drawer base

Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .

9

7 8

5

Fit the drawer back

Fit the drawer back
down onto the drawer
base .

Make sure that the
drawer base fits into
the groove in the drawer
back .

Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .

6

9

9

6

6

C

7 8

Attach the handles

Attach a handle to
each drawer front
using 2 screws .

L

F

Step 6

5

x 5

x 5

x 5

9

8

5

7

6

C

C

C

C

5

Step 7

Fit the wedgefixes

Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.

N

N

N

N

I

9

8

7

5

L

F

5

F

N

N

x 5

Finished

front edge

Assembly Instructions

6

Step 8

Prepare the left side

a: Place 5 runners on

the left side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

Screw 5 metal dowels
into the left side .

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .

M

1

Finished

front edge

I

M

I

B

1

M

I

1

Finished

front edge

I

M

Step 9

Prepare the right side

a: Place 5 runners on

the right side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

Screw 5 metal dowels
into the right side .

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .

M

2

I

B

2

M

I

2

a:

b:

B

B

I

M

I

M

I

M

I

M

I

M

B

B

B

M

1

I

I

I

I

I

Finished

front edge

I

M

I

M

I

M

I

M

I

M

B

B

B

B

B

1

2

2

I

I

I

I

I

Finished

front edge

Finished

front edge

a:

b:

Finished

front edge

Finished

front edge

Assembly Instructions

7

Step 10

Prepare the top

Tap 2 wooden dowels
into the top .

Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.

Insert 4 large locking
nuts into the
top .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

Fix the bracket in the
middle of the top ,
flush to the back edge
using screw .

Fit the top to the right
side

Push the top onto
the right side .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

Step 11

D

10mm

A

A

3

D

3

3

2

D

3

D

B

D

plain chipboard surface

3

A

D

D

D

A

Finished

front edge

D

G

K

K

G

K

3

plain chipboard surface

3

2

Assembly Instructions

8

Step 12

Step 13

Fit the 3 rails

Push the 3 rails onto
the right side .

Use a screwdriver to
tighten the large locking
nut fitted to each of
the 3 rails .

D

4

2

4

A

D

D

Prepare the 3 rails

Tap 2 wooden dowels
into each of the 3 rails .

Insert 2 large locking
nuts into each of the
3 rails .

A

A

4

4

D

4

x 3

plain chipboard surface

4

4

4

Note: Support the 2 rails
near the back of the unit
until the left side has been
fitted in the next step.

2

Assembly Instructions

9

Step 14

Fit the back

a: Square up the unit by

making sure that
measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the
outside edges of the
back .

Note: Nails should be
spaced about 150mm
apart.

10

J

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

10

Fit the left side

Push the left side
onto the assembly.

Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the top and the 3
rails .

D

1

3

4

Step 15

4

1

4

4

y

y

x

10

b:

J

x

3

Secure unit to a wall

To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by use of the metal
bracket fitted under
the top of the unit.

Fixings are not supplied
as they will need to suit
the wall type, and the
length of screw will
depend on the distance
of the back of the unit to
the wall.

Warning: Take

care when
drilling the wall that you
do not drill into any
pipes, wires etc. If in
doubt, consult an expert.

Assembly Instructions

10

Step 16

Step 17

Fit the plastic nails

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

Stand the unit up
for the next step.

O

1

2

K

3

O

1

2

O

O

O

K

WALL

WALL

Top of unit

K

3

Assembly Instructions

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Step 18

2nd threaded

hole

M

H

Fit the drawers

Starting with the bottom
drawer, slide both the
runners forward and
locate the drawer sides
. and between
them, lining up the holes
in the drawer wrap with
the 2nd 'threaded' holes
in the runners .

Working from the inside
of the drawer, insert 2
screws through the
sides and out into the
2nd threaded hole in the
runner.

Note: Do not over­tighten the screws .
If they catch on the
runner you may need
to loosen them slightly.

Assembly is complete

H

7 8

M

M

H

H

H

7

8

11

ALR3015

MADE IN

BRITAIN

Dimensions

Width - 69cm

Depth - 40cm

Height - 88.5cm

New Sywell - 5 Drawer Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 4 - 13/01/15

Important - Please read these instructions fully before starting assembly

257/7579

280/5935

282/2248

280/2110

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 28.5kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.

• Dispose of all packaging
carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Top (D2546A)

(658 x 394mm)

Drawer Front (D2550A)

(654 x 162mm) x 5

2

Rail (D2549A)

(658 x 78mm) x 3

3

4

5

10

Back (X684-524)

(854 x 684mm)

Left Side (D2552A)

(883 x 396mm)

Right Side (D2555A)

(883 x 396mm)

Drawer Base (T636-327)

(636 x 367mm) x 5

Drawer Back (W625-124)

(625 x 124mm) x 5

9

6

7 8

Left Drawer Side (W370-124LH)

(370 x 124mm) x 5

Right Drawer Side (W370-124RH)

(370 x 124mm) x 5

6

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

A

Wooden dowel (F22) x 8

B

Metal dowel (F901) x 20

C

D E F

G H I

L

Rule Scissors Hammer

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

M

J K

9mm Screw (F74) x 10 9mm Screw (F73) x 20

Drawer runner (F1004) x 10

Electric drill
(do not use for
fitting screws)

Knock-in Peg (F171) x 20

Small locking
nut (F3) x 10

Large locking
nut (F900) x 10

Nail (F51) x 21

Handle (F315) x 5

25mm Screw (F95) x 10

Plastic Nail (F91) x 4

N

Wedgefix (F639) x 20

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

x 5

B

Prepare the drawer
fronts

Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .

Note: Tighten the metal
dowels up fully against
the panels.

B

5

Prepare the drawer
sides

Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .

Note: Arrow on locking
nut must point towards
hole in edge of panel.

E

7

8

Step 2

Step 3

B

B

5

Attach the drawer
sides to the drawer
front

Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .

Turn the small locking
nuts on the left
drawer side and right
drawer side .

Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.

7
8

5

E

7
8

E

x 5 x 5

x 5

Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.

E

B

B

E

Small groove

9

Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.

E

E

7

8

8

7

5

Assembly Instructions

5

Step 4

Step 5

Fit the drawer base

Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .

9

7 8

5

Fit the drawer back

Fit the drawer back
down onto the drawer
base .

Make sure that the
drawer base fits into
the groove in the drawer
back .

Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .

6

9

9

6

6

C

7 8

Attach the handles

Attach a handle to
each drawer front
using 2 screws .

L

F

Step 6

5

x 5

x 5

x 5

9

8

5

7

6

C

C

C

C

5

Step 7

Fit the wedgefixes

Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.

K

K

K

K

9

8

7

5

L

F

5

F

K

K

x 5

Finished

front edge

Assembly Instructions

6

Step 8

Prepare the left side

a: Place 5 runners on

the left side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

Screw 5 metal dowels
into the left side .

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .

M

1

Finished

front edge

I

M

I

B

1

M

I

1

Finished

front edge

I

M

Step 9

Prepare the right side

a: Place 5 runners on

the right side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

Screw 5 metal dowels
into the right side .

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .

M

2

I

B

2

M

I

2

a:

b:

B

B

I

M

I

M

I

M

I

M

I

M

B

B

B

M

1

I

I

I

I

I

Finished

front edge

I

M

I

M

I

M

I

M

I

M

B

B

B

B

B

1

2

2

I

I

I

I

I

Finished

front edge

Finished

front edge

a:

b:

Finished

front edge

Finished

front edge

Assembly Instructions

7

Step 10

Prepare the top

Tap 2 wooden dowels
into the top .

Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.

Insert 4 large locking
nuts into the
top .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

Fit the top to the right
side

Push the top onto
the right side .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

Step 11

D

10mm

A

A

3

D

3

3

2

D

3

D

B

D

plain chipboard surface

3

A

D

D

D

A

Finished

front edge

D

plain chipboard surface

3

2

Assembly Instructions

8

Step 12

Step 13

Fit the 3 rails

Push the 3 rails onto
the right side .

Use a screwdriver to
tighten the large locking
nut fitted to each of
the 3 rails .

D

4

2

4

A

D

D

Prepare the 3 rails

Tap 2 wooden dowels
into each of the 3 rails .

Insert 2 large locking
nuts into each of the
3 rails .

A

A

4

4

D

4

x 3

plain chipboard surface

4

4

4

Note: Support the 2 rails
near the back of the unit
until the left side has been
fitted in the next step.

2

Assembly Instructions

9

Step 14

Fit the back

a: Square up the unit by

making sure that
measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the
outside edges of the
back .

Note: Nails should be
spaced about 150mm
apart.

10

J

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

10

Fit the left side

Push the left side
onto the assembly.

Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the top and the 3
rails .

D

1

3

4

Step 15

4

1

4

4

y

y

x

10

b:

J

x

3

Assembly Instructions

10

Step 16

Step 17

Fit the plastic nails

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

Stand the unit up
for the next step.

G

1

2

G

1

2

G

G

G

2nd threaded

hole

M

H

Fit the drawers

Starting with the bottom
drawer, slide both the
runners forward and
locate the drawer sides
. and between
them, lining up the holes
in the drawer wrap with
the 2nd 'threaded' holes
in the runners .

Working from the inside
of the drawer, insert 2
screws through the
sides and out into the
2nd threaded hole in the
runner.

Note: Do not over­tighten the screws .
If they catch on the
runner you may need
to loosen them slightly.

H

7 8

M

M

H

H

H

7

8

Assembly Instructions

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Step 18

11

ALR3015

Fit the overbalance
protector kit

To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an
alternative fixing method
of your choice.

Wall fixings are not
supplied as they will
need to suit the wall
type.

Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.

Assembly is complete

N

Attach the

strap to the unit

Attach the

strap to the wall

Wall fixing

(not supplied)

Washer

Strap

Strap

N

N

Example

Screw

(not supplied)

Washer

Screw

UNIT