Argos 2749390 ASSEMBLY INSTRUCTIONS
MADE IN
BRITAIN
Dimensions
Width - 70.5cm
Depth - 50cm
Height - 172cm
New Sywell - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 5 - 21/07/14
Important - Please read these instructions fully before starting assembly
282/4150
267/7606
266/2965
281/8960
266/3768
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 40.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2559A)
(674 x 494mm)
Left Side (D2560A)
(1711 x 496mm)
Base (D2562A)
(674 x 494mm)
Right Side (D2561A)
(1711 x 496mm)
Door (D2563A)
(1650 x 333mm) x 2
Rail (D2597A)
(674 x 125mm)
Back (X1682-700)
(1682 x 700mm)
2
3
4
7
5
Hanging Rail (FHR666)
(666mm long)
6
8
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B C
D E F
G H
Rule
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K L
Bracket (F327) x 1
Hinge plate
(F523) x 6
Hinge (F522) x 6
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Step
ladder
Ruler - Use this ruler to help correctly identify the screws
13mm Screw (F79) x 1 13mm Screw (F63) x 16
I
Electric drill
(only use
when drilling
into walls)
Large locking
nut (F900) x 10
Wooden dowel (F22) x 10
Metal dowel (F901) x 10
25mm Screw (F95) x 4
Rail Holder
(F891) x 2
Nail (F51) x 32
M
Handle (F315) x 2
Shelf stud (F110) x 2
N
Plastic Nail (F91) x 4
Finished
front edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Prepare the left side
Screw 5 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
B
1
Step 1
Step 2
K
K
K
K
B
B
B
B
B
B
F
I
F
I
F
I
F
1
K
1
I
F
1
F
F
I
F
B
B
B
B
B
K
K
K
K
Finished
front edge
Prepare the right side
Screw 5 metal dowels
into the right side .
Fit 3 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the right side .
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
B
2
K
2
I
F
2
F
2
A
Assembly Instructions
5
Step 3
Step 4
C
C
C
C
C
A
A
A
10mm
A
Prepare the top
Tap 4 wooden dowels
into the top .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the top .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
3
3
C
3
Finished
front edge
A
C
C
C
C
A
A
A
4
plain
chipboard
surface
Finished
front edge
Prepare the base
Tap 4 wooden dowels
into the base .
Insert 4 large locking
nuts into the base .
A
4
C
4
Finished
top edge
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 5
3
4
Fit the top and base
to the right side
Push the top and
base onto the right
side .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the top and base.
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
4
2
3 4
C
C
B
C
Step 6
plain
chipboard
surface
C
C
A
A
Prepare the rail
Tap 2 wooden dowels
into the rail .
Insert 2 large locking
nuts into the rail .
Step 7
A
5
C
5
2
5
Plain chipboard
surface
Fit the rail
Push the rail onto the
right side .
Use a screwdriver to
tighten the large locking
nut fitted to the rail .
5
2
C
5
2
Finished
top edge
5
Note: Support the
rail until the left
side has been fitted
in the next step.
Finished
front edge
Assembly Instructions
7
Step 8
Step 9
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the top , base and
rail .
1
C
3 4
5
5
1
3
4
b:
Fit the back and
plastic nails
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back ,
coloured surface facing
down, onto the unit as
shown.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
8
H
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
8
y
y
x
H
Warning: The
unit is heavy.
Lift with care.
8
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
N
1
2
N
Stand the unit up
for the next stage.
1
2
N
x
N
N
Fit the hanging rail
and shelf studs
Push the hanging rail
into the rail holders
fitted to the side panels.
Push the 2 shelf studs
up into the holes in the
top to act as door
buffers.
Assembly Instructions
8
Step 10
Step 11
6
I
6
6
I
Prepare the 2 doors
Push fit 3 hinges into
each of the 2 doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
F
L
7
90
L
L
F
F
L
F
F
L
F
F
7
x 2
G
3
3
G
G
Assembly Instructions
9
Step 12
Fit doors and handles
Note: The easiest way to
attach each door is
to fit the top hinge first,
then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door using 2
screws .
L
L
L
K
K
K
L
K
M
D
7
7
a: b:
c: d:
K
L
K
K
B
K
L
L
L
A
L
K
B
e:
M
D
7
7
M
D
Assembly Instructions
10
Step 13
b:
c:
d:
a:
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3010
Step 14
Top of Unit
WALL
WALL
Back of Unit
Fit the bracket
To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the
bracket fitted to the
top of the unit.
Fixings are not supplied,
as they will need to suit
the wall type and the
length of screw will
depend on the distance
from the back of the unit
to the wall.
Fix the bracket
loosely onto the top of
the unit using screw
and mark the wall for the
wall fixing.
Swivel the bracket
away from the wall and
drill a hole in the wall
using a suitable drill bit
and fit your wall fixing.
Swivel the bracket
back and fix the bracket
to the wall, then tighten
screw .
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Warning: The
unit is heavy.
Lift with care.
Assembly is complete
J
J
E
J
J
E
J
E
J
J
MADE IN
BRITAIN
Dimensions
Width - 70.5cm
Depth - 50cm
Height - 172cm
New Sywell - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 6 - 13/01/15
Important - Please read these instructions fully before starting assembly
282/4150
267/7606
266/2965
281/8960
266/3768
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 40.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance kit supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Top (D2559A)
(674 x 494mm)
Left Side (D2560A)
(1711 x 496mm)
Base (D2562A)
(674 x 494mm)
Right Side (D2561A)
(1711 x 496mm)
Door (D2563A)
(1650 x 333mm) x 2
Rail (D2597A)
(674 x 125mm)
Back (X1682-700)
(1682 x 700mm)
2
3
4
7
5
Hanging Rail (FHR666)
(666mm long)
6
8
Loading...