Argos 267-7905, 262-9049, 257-8633, 262-1449, 268-4943 ASSEMBLY INSTRUCTIONS

...
MADE IN
BRITAIN
Dimensions
Width - 38cm
Depth - 40cm
Height - 61cm
Malibu - 3 Drawer Bedside Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 9 - 28/07/14
Important - Please read these instructions fully before starting assembly
267/7905
262/9049
257/8633
262/1449
268/4943
266/8275
274/8762
249/7264
278/4056
267/8076
275/5449
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 14kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1 2
3
7
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Drawer Back (W317-124)
(317 x 124mm) x 3
Drawer Front (D2824A)
(345 x 156mm) x 3
Drawer Base (T328-367)
(328 x 367mm) x 3
Left Side (D2821A)
(591 x 394mm)
Plinth (D2825A)
(349 x 92mm)
Rail (D2826A)
(349 x 72mm)
Back Rail (D2836A)
(349 x 60mm)
Back (X511-373)
(511 x 373mm)
Left Drawer Side (W370-124LH)
(370 x 124mm) x 3
Right Drawer Side (W370-124RH)
(370 x 124mm) x 3
Right Side (D2822A)
(591 x 394mm)
10
5
Top (D2823A)
(388 x 396mm)
6
8 9
11 12
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 8
C
D
Large locking nut (F900) x 2
E
Small locking nut (F3) x 6
F
G
40mm Screw (F910) x 4
H
25mm Screw (F50) x 3 Handle (F631) x 3
I
J
Rule Scissors Hammer Eye protection
(when using a hammer or drill)
Cross-head screwdriver
Nail (F51) x 12
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
K
Drawer runner (F1004) x 6
Plastic Nail (F91) x 4
N
Wedgefix (F639) x 6
M
9mm Screw (F74) x 6
Knock-in Peg (F171GY) x 12
L
9mm Screw (F73) x 12
7
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 3
x 3
x 3
x 3
B
B
B
F
F
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
F
F
8
9
B
B
Step 2
Prepare the 3 drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
7
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
F
8
9
Attach the drawer sides to the drawer fronts
Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
8 9
7
F
F
8 9
7
8
9
L
L
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
11
8 9
7
10
8 9
11
10
10
L
Attach the handles
Attach a handle to each of the drawer fronts . using screw .
Note: Do not overtighten the screw.
I
H
7
8 9
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
N
x 3
x 3
x 3
L
L
x 3
N
N
N
11
8
9
7
10
8
9
11
I
H
7
Finished
front edge
A
Finished
front edge
Assembly Instructions
6
Step 8
Finished
front edge
K
J
K
J
Prepare the left side
a: Place 3 runners on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
Insert a large locking nut into the left side . .
Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.
Tap a wooden dowel into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
1
K
K
1
J
J
K
J
K
J
K
K
K
E
E
a:
b:
10mm
A
E
1
A
1
1
1
A
A
A
A
Assembly Instructions
7
Step 9
Prepare the right side
a: Place 3 runners on
the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
Insert a large locking nut into the right side . .
Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.
Tap a wooden dowel into the right side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
2
K
K
2
J
J
E
2
A
2
Finished
front edge
K
J
Finished
front edge
Finished
front edge
K
J
K
K
K
K
J
K
J
E
2
2
A
A
A
A
A
Step 10
Prepare the plinth, rail and back rail
a: Tap 2 wooden
dowels into the plinth . .
b: Tap 4 wooden
dowels into the rail .
a: Tap 2 wooden
dowels into the back rail .
A
A
4
A
6
5
Finished
front edge
plain chipboard surface
plain chipboard surface
plain chipboard surface
4
6
5
a:
a:
b:
c:
b:
Finished
front edge
G
G
Assembly Instructions
8
Step 11
Step 12
Fit the rail to the right side
Push the rail onto the right side .
5
2
plain chipboard surface
4
Finished
front edge
plain chipboard surface
Fit the plinth and back rail to the right side
Push the plinth onto the right side and secure it with screw .
Push the back rail onto the right side and secure it with screw . .
G
4
2
plain chipboard surface
5
2
G
6
2
6
2
Note: Support the back rail until the left side has been fitted in the next step.
Assembly Instructions
9
Step 13
Fit the left side
Push the left side onto the unit and secure it with 2 screws .
G
B
Prepare the top
Screw 2 metal dowels into holes shown on the underside of the top .
1
3
Step 14
1
G
G
B
B
plain chipboard surface
Finished
front edge
3
Assembly Instructions
10
Step 15
Fit the top
Push the top onto the side panels.
Use a screwdriver to tighten the large locking nut fitted to each side.
Note: Turn the large locking nut as far as it will go - more than 1/2 a turn.
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
down onto the unit, as shown.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
3
E
12
12
D
Step 16
E
B
3
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
b:
y
y
x
x
12
Loading...
+ 25 hidden pages