Argos 267-7905, 262-9049, 257-8633, 262-1449, 268-4943 ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 38cm

Depth - 40cm

Height - 61cm

Malibu - 3 Drawer Bedside Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 9 - 28/07/14

Important - Please read these instructions fully before starting assembly

267/7905

262/9049

257/8633

262/1449

268/4943

266/8275

274/8762

249/7264

278/4056

267/8076

275/5449

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 14kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

2

1 2

3

7

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Drawer Back (W317-124)

(317 x 124mm) x 3

Drawer Front (D2824A)

(345 x 156mm) x 3

Drawer Base (T328-367)

(328 x 367mm) x 3

Left Side (D2821A)

(591 x 394mm)

Plinth (D2825A)

(349 x 92mm)

Rail (D2826A)

(349 x 72mm)

Back Rail (D2836A)

(349 x 60mm)

Back (X511-373)

(511 x 373mm)

Left Drawer Side (W370-124LH)

(370 x 124mm) x 3

Right Drawer Side (W370-124RH)

(370 x 124mm) x 3

Right Side (D2822A)

(591 x 394mm)

10

5

Top (D2823A)

(388 x 396mm)

6

8 9

11 12

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 10

B

Metal dowel (F901) x 8

C

D

Large locking nut (F900) x 2

E

Small locking nut (F3) x 6

F

G

40mm Screw (F910) x 4

H

25mm Screw (F50) x 3 Handle (F631) x 3

I

J

Rule Scissors Hammer Eye protection

(when using a hammer or drill)

Cross-head screwdriver

Nail (F51) x 12

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

K

Drawer runner (F1004) x 6

Plastic Nail (F91) x 4

N

Wedgefix (F639) x 6

M

9mm Screw (F74) x 6

Knock-in Peg (F171GY) x 12

L

9mm Screw (F73) x 12

7

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 3

B

F

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

F

8

9

B

Step 2

Prepare the 3 drawer fronts

Screw 2 metal dowels into each of the drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

B

7

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

F

8

9

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

8 9

7

F

8 9

7

8

9

L

Assembly Instructions

5

Step 4

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

11

8 9

7

10

8 9

11

10

L

Attach the handles

Attach a handle to each of the drawer fronts . using screw .

Note: Do not overtighten the screw.

I

H

7

8 9

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

N

x 3

L

x 3

N

11

8

9

7

10

8

9

11

I

H

7

Finished

front edge

A

Finished

front edge

Assembly Instructions

6

Step 8

Finished

front edge

K

J

K

J

Prepare the left side

a: Place 3 runners on

the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the left side .

Insert a large locking nut into the left side . .

Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.

Tap a wooden dowel into the left side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

1

K

1

J

K

J

K

J

K

E

a:

b:

10mm

A

E

1

A

1

A

Assembly Instructions

7

Step 9

Prepare the right side

a: Place 3 runners on

the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the right side .

Insert a large locking nut into the right side . .

Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.

Tap a wooden dowel into the right side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

2

K

2

J

E

2

A

2

Finished

front edge

K

J

Finished

front edge

Finished

front edge

K

J

K

J

K

J

E

2

A

Step 10

Prepare the plinth, rail and back rail

a: Tap 2 wooden

dowels into the plinth . .

b: Tap 4 wooden

dowels into the rail .

a: Tap 2 wooden

dowels into the back rail .

A

4

A

6

5

Finished

front edge

plain chipboard surface

4

6

5

a:

b:

c:

b:

Finished

front edge

G

Assembly Instructions

8

Step 11

Step 12

Fit the rail to the right side

Push the rail onto the right side .

5

2

plain chipboard surface

4

Finished

front edge

plain chipboard surface

Fit the plinth and back rail to the right side

Push the plinth onto the right side and secure it with screw .

Push the back rail onto the right side and secure it with screw . .

G

4

2

plain chipboard surface

5

2

G

6

2

6

2

Note: Support the back rail until the left side has been fitted in the next step.

Assembly Instructions

9

Step 13

Fit the left side

Push the left side onto the unit and secure it with 2 screws .

G

B

Prepare the top

Screw 2 metal dowels into holes shown on the underside of the top .

1

3

Step 14

1

G

B

plain chipboard surface

Finished

front edge

3

Assembly Instructions

10

Step 15

Fit the top

Push the top onto the side panels.

Use a screwdriver to tighten the large locking nut fitted to each side.

Note: Turn the large locking nut as far as it will go - more than 1/2 a turn.

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

down onto the unit, as shown.

Nail around the outside edges of the back .

Note: Nails should be spaced about 150mm apart.

3

E

12

D

Step 16

E

B

3

D

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

b:

y

x

12

Assembly Instructions

11

Step 17

ALR3028

Fit the 4 plastic nails

Tap 2 plastic nails into the bottom edge of each side and as shown.

Stand the unit up for the next step.

C

1 2

C

Fit the drawers

Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .

Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.

Note: Do not overtighten the screws. If they catch on the runner you may need to loosen them slightly.

Assembly is complete

M

J

2nd threaded

hole

J

M

8 9

M

Step 18

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

1

2

MADE IN

BRITAIN

Dimensions

Width - 74.5cm

Depth - 50cm

Height - 181cm

Malibu - 3 Drawer 2 Door Robe

Assembly Instructions - Please keep for future reference

227/8232

258/7679

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 10 - 22/04/15

Important - Please read these instructions fully before starting assembly

238/3574

237/1287

258/2904

279/1496

258/8032

279/1960

257/2512

262/6217

255/7788

247/7662

249/6612

278/0830

278/5189

266/7355

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 49.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not

recommend the

use of power

drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the strap supplied.

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

2

1

10

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

2 5

4

3

11

Left Side (D2871A)

(1808 x 496mm)

Base (D2841A)

(716 x 476mm)

Top (D2870A)

(716 x 494mm)

Right Side (D2872A)

(1808 x 496mm)

12

Plinth (D2873A)

(716 x 92mm) x 2

9

6

Back Rail (D2847A)

(716 x 92mm)

Rail (D2874A)

(716 x 92mm)

Drawer Base (T693-367)

(693 x 367mm) x 3

Left Drawer Side (W370-124LH)

(370 x 124mm) x 3

Right Drawer Side (W370-124RH)

(370 x 124mm) x 3

Door (D2857A)

(1198 x 353mm) x 2

Drawer Back (W682-124BCK)

(682 x 124mm) x 3

14

Drawer Front (D2783A)

(710 x 156mm) x 3

Back (X1710-740)

(1710 x 740mm)

7 8

Hanging Rail (FHR704)

(704mm long)

13

15