Argos 227/8232, 237/1287, 238/3574, 258/2904, 258/7679 Assembly Instructions Manual
...
MADE IN
BRITAIN
Dimensions
Width - 74.5cm
Depth - 50cm
Height - 181cm
Malibu - 3 Drawer 2 Door Robe
Assembly Instructions - Please keep for future reference
227/8232
258/7679
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 9 - 12/01/15
Important - Please read these instructions fully before starting assembly
238/3574
237/1287
258/2904
279/1496
258/8032
279/1960
257/2512
262/6217
255/7788
247/7662
249/6612
278/0830
278/5189
266/7355
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 49.5kgs. Please
lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
strap supplied.
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
1
10
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
2 5
4
3
11
Left Side (D2871A)
(1808 x 496mm)
Base (D2841A)
(716 x 476mm)
Top (D2870A)
(716 x 494mm)
Right Side (D2872A)
(1808 x 496mm)
12
Plinth (D2873A)
(716 x 92mm) x 2
9
6
Back Rail (D2847A)
(716 x 92mm)
Rail (D2874A)
(716 x 92mm)
Drawer Base (T693-367)
(693 x 367mm) x 3
Left Drawer Side (W370-124LH)
(370 x 124mm) x 3
Right Drawer Side (W370-124RH)
(370 x 124mm) x 3
Door (D2857A)
(1198 x 353mm) x 2
Drawer Back (W682-124BCK)
(682 x 124mm) x 3
14
Drawer Front (D2783A)
(710 x 156mm) x 3
Back (X1710-740)
(1710 x 740mm)
7 8
Hanging Rail (FHR704)
(704mm long)
13
15
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 14
B
Metal dowel (F901) x 6
D F
G
40mm Screw (F910) x 14
H
25mm Screw (F50) x 8 Handle (F631) x 8
I
Nail (F51) x 33
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
K
M ON
P Q
Small locking
nut (F3) x 6
Rail holder
(F1014) x 2
E
13mm Screw (F63) x 10
19mm Connecting bolt
(F461) x 2
Hinge plate
(F523) x 4
Hinge (F522) x 4
25mm Connecting sleeve
(F432) x 2
Ruler - Use this ruler to help correctly identify the screws
Tools required
R S
J
Drawer runner (F1004) x 6
Knock-in Peg (F171GY) x 12
C
Plastic Nail (F91) x 5
9mm Screw (F74) x 6
L
9mm Screw (F73) x 12
Wedgefix (F639) 12
Rule
Square
Scissors
Spirit level
Hammer
Bradawl
Electric drill
Step ladder
Cross-head screwdriver
Eye protection (when
using a hammer or drill)
T
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 3
x 3
x 3x 3
B
B
B
E
Step 2
Prepare the 3 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
E
6
7
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
6
7
5
E
E
6
E
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
E
E
6
7
5
B
B
5
6
7
7
5
Assembly Instructions
5
Step 4
R
R
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
9
6 7
5
8
6 7
9
8
8
R
Attach the handles
Attach a handle to
each of the drawer fronts
. using screw .
Note: Do not
overtighten the screw.
I
H
5
x 3
x 3
x 3
R
R
6 7
x 3
Step 7
J
J
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
J
9
6
7
5
8
6
7
9
H
H
5
I
I
J
J
J
Loading...