Mia Bed
Assembly Instructions - Please keep for future reference
White 2572141
Pink 2665924
Dimensions
:
Width
Depth
Height
197.3 cm
:
99.5 cm
:
85.5 cm
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Argos Customer Helpline: 0845 640 30 30
350267
Issue 1 - 26-05-2014
Safety and Care Advice
!
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• We do not recommend the use
of power drill/drivers for
inserting screws, as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
.
Note !
• This childs bed conforms to BS 8509:2008 +A1:2011.
• Age recommendation: from 3 year to 12 years.
• Mattress in size 90x190 cm to be used with this bed.
• Children are likely to play, bounce ,jump and climb on beds, therefore the childs bed should not
be placed too close to other furniture or windows, and should be placed either tight to any wall or
have a gap 300mm between the wall and the side of bed.
• Any additional or replacement parts are obtained from the manufacturer or distributor.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page
with these instructions for
future reference.
1
If you have damaged or missing components, call
Components - Panels
the Argos Customer Helpline: 0845 640 30 30
Please check you have all the panels listed below
3
Headboard
(89,5 cm x 64 cm)
Post, headboard
1
(83 cm x 5,0 cm)
5
Side rail
(189,7 cm x 14,5 cm)
x
2
2
Post, foot
(55 cm x 5 cm)
x
2
6
Spacer block
(7,1 cm x 2,2 cm)
4
Footboard
(89,5 cm x 54,5 cm)
7
x
14
Slat
(91,8 cm x 6,8 cm)
8
350267-03
Drawer front
(189,1 cm x 19,7 cm)
11
Drawerback
(186,5 cm x 14,5 cm)
12
Drawer bottom
(187,5 cm x 41,0 cm)
9
Drawerside, left
(41,3 cm x 14,5 cm)
13
Drawer rail
(40,0 cm x 6 cm)
x
10
Drawerside, right
(41,3 cm x 14,5 cm)
2
2
Components - Fittings
Please check you have all the panels listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
Aa
ø7.8 x 40mm Wooden dowel x
Cb
ø5 x 8, cc34mm Bolt x
Hg
M6 x 70mm Threaded rod x
Na
M6 x 10mm Nut x
ø35mm Wheel xTa4
6mm Allen key xYc1
12
4
4
20
Bv
ø3,5 x 30mm Screw x
Ec
ø35mm Cap x
Hw
M6 x 80mm Bolt x
Ne
M6 x 20mm Bushing x
4mm Allen key xYa1
4
8
4
28
Ca
ø15 x 10.5mm Cam x
Fm
ø35mm Bracket x
Ke
ø6.1 x 11.5mm Screw x
Nf
M6, ø10 x 12.5mm barrel nut x
Yb
10/13mm Wrench x
12
4
8
1
8
Tools required
Phillips screwdriver
(Medium & large)
Flatblade screwdriver
(Medium)
Hammer
Ruler - Use this ruler to help correctly identify the screws
3
17060 16040 90 15013070 120100 14011050 803020100
350267-04
Assembly Instructions
Step 1
Assembly of the bed.
Step 1.1
Knock the dowels Aa into
the holes indicated on
5
the side rails
small hammer.
using a
1
5
Aa
ø7.8 x 40mm Wooden dowel x
1
3
2
8
7
x
14
5
4
2
Aa
Aa
Step 1.2
Screw the bushings Ne into
the holes indicated on the
1
posts
Use the allen key
and 2.
Yc
.
Ne
M6 x 20mm Bushing x
Ne
x
2
5
4
x
1
Ne
6mm Allen key xYc1
2
350267-05
x
2
2
4
Assembly Instructions
Step 1.3
Fix the posts 1 onto
3
the headboard
Hw
bolts
nuts
into the barrel
Nf
.
Note - the holes in the
posts for the siderails
must point downwards.
using
Hw
Hw
M6 x 80mm Bolt x
Nf
1
Hw
Nf
8
M6, ø10 x 12.5mm barrel nut x
8
Ya
4mm Allen key x
1
Note NO holes !
The holes for the
siderails on reverse side !
Nf
3
Nf
Nf
Hw
Hw
1
Fix the posts
footboard
Hw
into the barrel nuts Nf.
2
onto the
4
using bolts
Make sure to place
the posts
footboard
2
onto the
4
exactly as
shown.
Note - the holes in the
posts for the siderails
must point upwards.
Use the allen key Ya.
Hw
2
Hw
Note the holes for
the siderails !
Nf
Hw
2
Nf
Nf
Nf
4
Hw
m
m
3
6
2
Nf
Hw
4
Hw
m
m
8
8
2
5
2
350267-06
Assembly Instructions
Step 1.4
Screw the threaded rods
Hg
into the bushings Ne in
1
the posts
and 2.
Step 1.5
Fm
Hg
Hg
M6 x 70mm Threaded rod x
4
Hg
1
Hg
1
2
Hg
2
Na
Place the side rails
5
onto the headboard posts
1
.
Push the brackets
the nuts
Na into the holes
Fm
and
indicated on the side rails
5
and onto the threaded
Hg
rods
Tighten the nuts
the wrench
.
Na using
Fm
.
ø35mm Bracket x
2
M6 x 10mm Nut x
2
Yb
10/13mm Wrench x
1
1
Fm
Fm
Na
Na
5
350267-07
Produced by:
NJA Furniture A/S
DK-7700 Thisted
Safety requirements:
EN BS 8509:2008+A1:2011
Prod. wk/year: xx/201x
1
5
6
Assembly Instructions
Step 1.6
Place the footboard posts
2
onto the side rails 5.
Fm
.
Ec into
5.
Fm
and
Na using
Push the brackets
the nuts
Na into the holes
indicated on the side rails
5
and onto the threaded
Hg
rods
.
Tighten the nuts
the wrench
Insert the caps
the holes indicated on
the side rails
Fm
ø35mm Bracket x
2
Ec
ø35mm Cap x
4
Na
M6 x 10mm Nut x
2
Yb
10/13mm Wrench x
1
2
Na
Fm
5
Fm
Na
5
2
Step 1.7
Fix the rst of the slats 7
to the slatholders using
Bv
screws
The slats
distributed evenly in the
bedframe. To get the
distance right use the
spacer block
See detail.
.
7
must be
6
as shown.
Bv
Ec
Bv
ø3,5 x 30mm Screw x
2
6
Bv
7
7
7
350267-08
Assembly Instructions
Step 1.8
Fix the second of the slats
7
to the slatholders using
Bv
screws
To get the distance right
use the spacer block
shown.
See detail.
.
6
as
Bv
Bv
ø3,5 x 30mm Screw x
Bv
7
2
6
7
Step 1.9
Fix the rest of the slats 7
Bv
using screws
To get the distance right
use the spacer block
shown.
See detail.
.
6
as
Bv
ø3,5 x 30mm Screw x
6
7
Bv
24
7
7
Bv
350267-09
8
Assembly Instructions
Step 2
Assembly of the drawer.
9
12
13
8
13
11
10
Step 2.1
Screw the bolts Cb into
the holes indicated on the
11
drawer back
drawer sides
and the
9
and 10.
Knock the dowels Aa into
the holes indicated on
drawer back 11, the
the
9
drawer sides
and 10
and the
Aa
13
drawer rails
using a
smal hammer.
Step 2.2
Aa
ø7.8 x 40mm Wooden dowel x
Aa
Cb
13
11
9
Aa
Ke
12
Cb
Cb
ø5 x 8, cc34mm Bolt x
Aa
Cb
Cb
Ta
6
Aa
10
Aa
Fix the wheels Ta onto
the drawer sides 9 and
10
using screws Ke.
See detail.
9
ø6.1 x 11.5mm Screw x
8
9
Ta
Ke
Ke
ø35mm Wheel x
Ke
Ta
Ke
Ta
4
10
Ke
Ta
350267-10
Assembly Instructions
Step 2.3
Screw the bolts Cb into
the holes indicated on
8
the drawer front
Cb
.
Step 2.4
Push the drawer sides 9
10
and
rails
back
Place cams
holes indicated. Arrow
pointing towards the front.
Turn the cams
right to x the drawer
back.
and the drawer
13
onto the drawer
11
.
Ca
into the
Ca
to the
Cb
ø5 x 8, cc34mm Bolt x
Cb
Ca
ø15 x 10.5mm Cam x
Cb
6
Cb
8
6
10
13
Ca
Ca
13
11
Ca
Step 2.5
Slide the drawer bottom
12
into the drawer
9
sides
and 10.
9
Ca
12
10
9
350267-11
10
Assembly Instructions
Step 2.5
Push the drawer front 8
onto the drawer sides
10
and
rails
and the
13
.
drawer
Place cams Ca into the
holes indicated. Arrow
pointing towards the front.
Ca
Turn the cams
to the
right to x the front.
9
Ca
13
Ca
Ca
ø15 x 10.5mm Cam x
6
Ca
8
10
Ca
13
Step 2.6
Place the drawer.
9
11
350267-12
Loading...