Argos 2275170, 2377951, 2476302 ASSEMBLY INSTRUCTIONS

New Penton - Dressing Table
Assembly Instructions - Please keep for future reference
227/5170
247/6302
237/7951
Dimensions
Width - 80cm
Depth - 48cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Issue 1 - 14/05/14
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Check you have all the components and tools listed on pages 2 and 3.
Remove all fittings from the plastic bags and separate them into their groups.
Keep children and animals away from the work area, small parts could choke if swallowed.
Make sure you have enough space to layout the parts before starting.
Do not stand or put weight on the product, this could cause damage.
Assemble the item as close to its final position (in the same room) as possible.
Assemble on a soft level surface to avoid damaging the unit or your floor.
This product has been produced from natural timber; you may notice some variation in the grain and colour of different component parts which is normal for furniture produced using natural wood and is not the result of any manufacturing fault.
The product has been treated with a wax and oil finish to prevent dirt ingress and preserve moisture.
On unpacking the furniture you may notice an odour due to this treatment; this will disappear once the furniture is unpacked and assembled after a period of time.
This process may leave some staining on the packaging material; please take care to ensure this does not transfer to clothing or carpeted surfaces during assembly.
We do not recommend the use of power drill/drivers for
inserting screws,
as this could damage the unit. Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
Care and maintenance
Use an appropriate furniture polish for natural wood furniture and a dry cloth to clean the product.
Avoid placing the furniture in direct sunlight as this will cause the timber to prematurely age.
From time to time check that there are no loose screws on this unit.
This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
1
Components - Panels
Please check you have all the panels listed below
Top panel (80 x 48cm)
1
Back panel (76.2 x 18cm)
6
Cross rail (74.4 x 11.2cm)
7
Right side panel (73.2 x 46cm)
2
Left side panel (73.2 x 46cm)
3
Right front frame (73.2 x 9.2cm)
4
Drawer bottom (57.6 x 32.6cm)
8
Drawer front (59 x 14cm)
9
Drawer side x 2 (34 x 14cm)
10
Drawer back (56.6 x 14cm)
11
Left front frame (73.2 x 9.2cm)
5
Side drawer runner x 2 (37.4 x 8cm)
13
12
Block x 4 (10 x 2cm)
13
2
If you have damaged or missing components,
Components - Fittings
call the
Customer Helpline: 08456 400 800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel x 16
D
22mm Bolt x 4
G
Drawer handle x 2
B
E
Metal dowel x 10
H
Nail x 12
C
35mm Screw x 1830mm Screw x 8
F
Locking nut x 10
Tools required
Phillips screwdriver (small & medium)
Small hammer
Ruler - Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
m
2
Ruler/tape measure
Eye protection (when using a hammer or glue)
3
Assembly Instructions
Step 1
Fixing right front frame.
(Two people required for an easier assembly).
a: Insert right side panel
2
into right front frame
4
through joints.
Note:
Before fixing the
blocks into place it is important to ensure that the slot and groove of parts and are fully pushed together and lined up correctly at the top and bottom.
b: Place blocks
between the two marks on the front frame as shown. First fix to the side panel using screws .
13
2
13
C
4
a: b: c:
4
C
2
13
Yes!No!
13
2
Attention: correct position of panel.
4
C
13
c: Fix front frame through
blocks using screws
13
C
.
Step 2
Fixing left front frame.
(Two people required for an easier assembly).
a: Insert left side panel
3
into left front frame
5
through joints.
Note:
Before fixing the
blocks into place it is important to ensure that the slot and groove of parts and are fully pushed together and lined up correctly at the top and bottom.
b: Place blocks
between the two marks on the front frame as shown. First fix to the side panel using screws .
13
3
13
C
5
Top
a: b: c:
5
C
3
13
Yes!No!
5
13
13
3
C
Attention: correct position of panel.
c: Fix front frame through
blocks using screws
13
C
.
Top
4
Assembly Instructions
Step 3
Insert dowels into the
A
indicated parts.
A
A
2
7
A
A
2x
12
A
A
3
A
Step 4
Fitting Metal dowels.
Screw metal dowels into top panel , side panels and .
2
dowels as far as shown.
Do not over tighten.
1
3
Insert metalNote:
E
E
3
E
2
E
E
E
1
5
Assembly Instructions
Step 5
Fixing cross rail.
Two people required for an easier assembly.
With help, fit side panels
2
rail .
Insert 4 locking nuts into cross rail where shown.
Use a screwdriver to turn locking nuts clockwise to lock.
Do not over tighten.
3
and to the cross
7
F
F
F
3
F
2
7
F
Step 6
Fixing top panel.
Caution:
Carefully lay the top panel on a soft and clean surface to avoid damaging the product.
With help, fit cabinet to the top panel .
Insert 6 locking nuts into side panels where shown.
Use a screwdriver to turn locking nuts clockwise to lock.
Do not over tighten.
1
F
F
F
F
F
F
F
1
Attention: correct position of panel.
6
Assembly Instructions
Step 7
Fixing side drawer runners.
a: Fit side drawer
runners to side panels. Fit and push dowels into the front frame first.
12
b: Attach side drawer
runners using screw .
C
Step 8
Fixing back panel.
Important:
Cabinet beMUST ‘square’ when back panel are attached.
12
12
a:
12
b:
C
a: Attach back panel
using nails .
With help, carefully stand the product upright.
7
H
6
H
6
H
H
Assembly Instructions
Step 9
Drawer assembly.
a: Attach drawer sides
10
to the drawer front
9
using screws .
B
b: Slide drawer bottom
8
into slots on drawer
sides and position drawer
11
back in place.
c: Holding the drawer
11
back , press the drawer sides and fix them using screws .
d: Using bolts attach
the drawer handle to the drawer front.
B
D
G
a:
10
B
10
9
B
B
b:
11
8
c:
d:
B
D
D
Step 10
Insert drawer into unit. With the back of the drawer past the front frames, use a hammer to tap dowels in flush to drawer sides. This is a safety catch to stop drawer falling out.
Assembly is complete.
A
G
G
A A
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
8
Loading...