Wooden Filer
Assembly Instructions
-
Please keep for future reference
227/6966
Dimensions
Width - 39cm
Depth - 39.5cm
Height - 80cm
Important
-
-
Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Version 1 Date: 28/04/14
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fi ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your fl oor.
• Parts of the assembly will be
easier with 2 people.
power drill is set on a low torque
setting.
Glue safety - Take care when using glue, please follow the advice below
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
• To reduce
the likelihood of
damaging your
product please
ensure that your
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• From time to time check that
there are no loose screws on
this unit.
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Pilot holes
for guidance
only
Argos = 0345 6400800
Right side panel
1
(38.9 x 78.3cm)
Top panel
4
(39 x 39cm)
Front bottom panel
5
(35.8 x 11cm)
Finished front edge
Left side panel
2
(38.9 x 78.3cm)
Small drawer front x 3
9
(35.1 x 13.8cm)
Small drawer right side
10
(34 x 11.5cm)
x 3
Small drawer left side
11
x 3
(34 x 11.5cm)
Back panel
3
(38.5 x 76cm)
Large drawer right side
14
(34 x 26cm)
Large drawer left side
15
(34 x 26cm)
Middle panel
6
(35.8 x 11cm)
Back bottom panel
7
(35.8 x 11cm)
Front panel
8
(35.8 x 5cm)
Small drawer back
12
(32.6 x 11.5cm)
x 3
Large drawer front
13
(35.1 x 30cm)
Large drawer back
16
(32.6 x 26cm)
Drawer bottom x 4
17
(33.6 x 33.6cm)
2
Components - Fittings
Please check you have all the fi ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fi ttings
may be supplied than are required.
A
Runner x 8
D
39mm Locking pin x 26
G
15mm Locking nut x 10
J
Glue x 1
M
Handle x 4
P
Wall plug x 1
B
(This Screw is included
in the bag of runner)
12mm Screw x 24
E
14mm Screw x 5
H
Nail x 14
K
Plastic file support x 2
N
12mm Screw x 8
C
30mm Dowel x 8
F
Plastic support x 2
I
12mm Locking nut x 16
L
30mm Screw x 24
(This screw is
O
included in the
wall strap bag)
Wall strap x 1
x 1
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Drill
7mm Suitable drill bit
(for use with wall plug)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
3
105
Small
hammer
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
110 115 120 125 130 135 140 145 150 155 160 165 170
Assembly Instructions
Step 1
Attaching runners
Position Runners in
a:
A
front edge of the Right
side panel .
1
Slide top of the Runners
A
back.
Use screws to fix the
Runners on the Right
side panel .
B
A
1
a:
1
A
A
A
A
A
B
1
Middle hole
B
B
B
1.7cm
B
Pilot holes for
runner position
Finished front edge
Slide top of Runners
b:
A
forward and fix as
shown using Screws .
B
b:
Place a small amount of
J
Glue into the dowel
holes.
Insert Dowels into the
Right side panel .
C
1
Screw Locking pins(3pcs)
D
into the Right side
panel
.
1
Note:
Insert locking pins
as far as shown.
Do not over tighten.
Middle hole
B
B
B
B
B
B
B
D
D
1
B
A
A
D
B
B
B
C
J
D
A
1
C
J
Continued on next page.
A
A
A
4
Assembly Instructions
Step - continued 1
Position Runners in
c:
A
front edge of the Left side
panel .
2
Slide top of the Runners
A
back.
Use screws to fix the
Runners on the Left
side
panel .
B
A
2
c:
1.7cm
Finished
front edge
B
Middle hole
B
A
2
2
A
B
B
B
A
A
A
Pilot holes for
runner position
Slide top of Runners
d:
A
forward and fix as
shown using Screws .
B
Place a small amount of
J
Glue into the dowel
holes.
Insert Dowels into the
Left side panel .
Screw 3 Locking pins
the Left side panel
into
.
2
Note:
Insert locking pins
C
2
D
as far as shown.
Do not over tighten.
d:
2
A
A
A
D
D
B
D
A
B
B
B
Middle hole
A
D
B
B
B
B
C
J
B
B
C
J
2
5
Assembly Instructions
Step 2
Attaching plastic
supports
a:
Use Screws to fix
Plastic supports onto
E
F
the Front bottom panel
5
.
b:
Use Screws to fix
Front bottom panel
onto the Front panel .
E
5
8
Place a small amount of
J
Glue into the dowel
holes.
Insert Dowels into the
Front bottom panel .
C
5
Step 3
Attaching bottom panel
and support panel
a:
Place a small amount
of Glue into the dowel
holes.
J
a:
b:
a:
E
E
F
5
E
C
5
8
Finished
C
front edge
6
E
F
E
J
C
C
7
J
F
C
J
C
J
C
J
Insert Dowels into the
Middle panel and
Back bottom panel .
b:
Position Front bottom
panel and and Front
panel onto the Left
5
8
side panel .
Insert Locking nuts
C
6
7
2
G
into the Front bottom
panel .
Use a screwdriver to turn
Locking nuts
5
G
clockwise to lock.
Continued on next page.
b:
C
G
Unfinished
back edge
2
5
8
G
6
Assembly Instructions
continuedStep 3 -
c:
Position Middle panel
6
and Back bottom panel
7
onto the Left side
panel .
Insert Locking nuts
into the Middle panel
and Back bottom panel
.
Use a screwdriver to turn
Locking nuts
2
G
6
7
G
clockwise to lock.
c:
G
Unfinished
back edge
7
G
6
G
2
d:
Position Right side
panel onto the unit.
Insert Locking nuts
1
G
into the Front bottom
panel , Middle panel
and Back bottom panel
.
5
6
7
Use a screwdriver to turn
Locking nuts
G
clockwise to lock.
d:
G
1
7
G
G
5
G
6
7
Assembly Instructions
Step 4
Attaching top panel
a:
Screw Locking pins
into the Top panel .
Insert Locking pins
Note:
D
4
as far as shown.
Do not over tighten.
b:
Carefully locate the
Top panel onto the
4
unit.
a:
b:
D
D
D
D
4
G
D
Insert 4 Locking nuts
G
into the unit.
Use a screwdriver to turn
Locking nuts clockwise
G
to lock.
Unfinished
back edge
G
G
4
1
G
G
2
8
Assembly Instructions
Step 5
Fixing back panel
Attach Back panel
onto the unit using Nails
H
.
Important:
The unit
be ‘square’ when
back is attached.
3
MUST
H
Unfinished
back surface
3
Step 6
Small drawer assembly
a:
Screw Locking pins
into the Small drawer front
9
.
Insert Locking pins
Note:
as far as shown.
Do not over tighten.
Continued on next page.
9
a:
D
D
D
D
D
D
9
Assembly Instructions
continuedStep 6 -
b:
Fix Small drawer left
11
side onto the Small
drawer front .
Fix Small drawer right
c:
side onto the Small
10
drawer front
9
.
9
Insert 2 Locking nuts
I
into the holes (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
I
to lock.
b:
11
9
c:
I
10
11
9
I
d:
Insert 2 Locking nuts
I
into the holes (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
I
to lock.
Place a small amount of
J
Glue into the grooves.
Carefully slide the Drawer
bottom into the
17
grooves.
e:
Place a small amount
of Glue into the groove
J
on the Small drawer back
12
.
d:
e:
I
I
17
I
I
J
11
9
J
12
J
J
Continued on next page.
10
Assembly Instructions
continuedStep 6 -
f:
Position the Small
drawer back onto the
unit using Screws .
g:
Use Screws to fix the
Drawer handle onto the
Small drawer front .
12
L
L
M
9
f:
g:
L
L
12
L
17
L
11
L
17
9
L
Step 7
Large drawer assembly
a:
Screw Locking pins
into the Large drawer
13
front .
Insert Locking pins
Note:
as far as shown.
Do not over tighten.
b:
Fix Large drawer left
15
side onto the Large
drawer front .
13
D
a:
b:
M
D
D
D
D
13
15
X 3
D
Continued on next page.
11
13
Assembly Instructions
continuedStep 7 -
Fix Large drawer right
c:
side onto the Large
14
drawer front
.
13
c:
I
14
Insert 2 Locking nuts
I
into the holes (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
I
to lock.
d:
Insert 2 Locking nuts
I
into the holes (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
I
to lock.
Place a small amount of
J
Glue into the grooves.
Carefully slide the Drawer
bottom into the
17
grooves.
d:
15
13
I
I
I
I
I
17
13
J
15
J
e:
Place a small amount
of Glue into the groove
J
on the Large drawer back
16
.
f:
Position the Large
drawer back onto the
unit using Screws .
Continued on next page.
16
L
e:
f:
J
16
L
L
16
L
17
15
L
J
12
Assembly Instructions
Step 7 -
g:
Use Screws to fix the
Handle onto the Large
drawer front .
Position Plastic filer supports
K
onto the Drawer side
panels.
M
continued
L
13
Step 8
g:
K
Left Right
K
L
L
M
13
K
K
Inserting drawers
With help, carefully stand
unit upright.
Warning:
The unit is heavy.
Lift with care.
a: Pull runners out. Slide
drawers onto runners so
they butt up against back
of drawer front.
b: Fix through drawer
sides into runners using
screws
N
.
a:
N
9
9
9
N
N
N
1
13
13
N
b:
Assembly Instructions
Step 9
Fixing to wall
It is recommended that
the unit is fixed to a wall.
Fix Wall strap to back
O
of top panel using Screw
E
.
With help, move the unit
into position.
Warning:
The unit is
heaty.
Lift with care.
Mark fixing hole on wall
and remove unit.
Drill a hole and insert Wall
P
pulg .
O
Top panel
Wall plugs supplied are
Note:
for solid wall only.
P
O
wall
E
The correct type of fixing must
be used for your wall, seek
professional advice if in doubt
O O P
Back panel
Warning:
Before drilling,
check wall for
hidden pipes
and cables.
Reposition the unit and fix
wall strap using Screw .
Assembly is complete.
O
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
14
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
Types of walls
No.1 “General Purpose” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
No.2 “Plasterboard” wall plug
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
No.3 “Cavity Fixing” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
For use with walls stuck with
is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
Revision 2 - 7/10/09
Loading...