Argos 2273237 ASSEMBLY INSTRUCTIONS

Osaka Dressing Table

Assembly Instructions - Please keep for future reference

White 2273237

Black 2281511

Dimensions

:

Width

Depth

Height

101.2 cm

:

40.0 cm

:

76.0 cm

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Argos Customer Helpline: 0845 640 30 30

350265

Issue 1 - 23-05-2014

Safety and Care Advice

!

Important - Please read these instructions fully before starting assembly

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor.

• Parts of the assembly will be easier with 2 people.

• From time to time check that there are no loose screws on this unit.

• We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Dispose of all packaging carefully and responsibly

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

.

Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

1

If you have damaged or missing components, call

Components - Panels

the Argos Customer Helpline: 0845 640 30 30

Please check you have all the panels listed below

Top

1

(101,2 cm x 40 cm)

3

Side, right

(15 cm x 30,6 cm)

2

Side, left

(15 cm x 30,6 cm)

6

Back rail

(88,2 cm x 15 cm)

7

8

Drawerfront

(29,0 cm x 12,5 cm)

Front rail

(88,2 cm x 6 cm)

x

3

9

Drawer side, right/left

(31 cm x 9,8 cm)

x

5

4

Leg, left

(74,5 cm x 5,0 cm)

10

Drawer back

(24,5 cm x 9,8 cm)

Leg, right

(74,5 cm x 5,0 cm)

x

2

x

3

x

2

6

350265-03

11

Drawer bottom

(25,3 cm x 30,7 cm)

x

12

Divider

(11,9 cm x 29,1 cm)

x

2

3

2

Components - Fittings

Please check you have all the panels listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings

may be supplied than are required.

Aa Ab

ø8 x 40mm Wooden dowel x

Ca

ø15 x 10.5mm Cam x

Fh

Wall strap and instruction x 1

Kb

ø5.8 x 8mm Screw x

Sk

245 x 17 x 10mm Drawer runner x

28

8

26

ø6 x 30mm Wooden dowel x

Cp

ø5 x 11, cc34mm Bolt x

Fi

Back fitting w. ø3.5 x 15mm Screw x

Hd

M4 x 20mm Screw x

Kf

ø5.8 x 19mm Screw x

12

Bp

12

28

3

6

ø3 x 35mm Screw x

Dj

ø5 x 38mm Screw x

Ge

6

ø27 x 24mm Metal Knob x

Hk

M4 x 9mm Screw x

Nu

ø10 x 9mm Spacer x

12

4

3

6

Tools required

Phillips screwdriver (Medium & large)

Flatblade screwdriver (Medium)

Hammer

Ruler - Use this ruler to help correctly identify the screws

3

17060 16040 90 15013070 120100 14011050 803020100

350265-04

Assembly Instructions

Step 1

Assembly of the table.

1

3

Step 1.1

Knock the dowels Aa into the holes indicated on the sides

2 and 3

using a small hammer.

Step 1.2

Screw the bolts Cb into the holes indicated on the

4

legs

and 5.

Aa

Cp

Aa

6

12

7

2

4

5

4

Aa

3

Aa

ø8 x 40mm Wooden dowel x

2

Aa

16

Aa

Cp

ø5 x 11, cc34mm Bolt x

8

5

x

2

Step 1.3

Place the legs 4 and

5

onto the sides 2

3

and

Push cams holes indicated on the sides Arrows pointing towards the legs

Turn the cams

right to x the legs

and

.

2

5

.

Ca

into the

and 3.

4/5

.

Ca

to the

4

Cp

4

x

2

Ca

ø15 x 10.5mm Cam x

8

4

Ca

5

4

5

Ca

3

2

350265-05

4

Assembly Instructions

Step 1.4

Screw the bolts Cb into the holes indicated on the

2

sides

and 3.

Step 1.5

Slide the top of the

Sk

drawer runners backwards. You can identify the front end of the drawer runner the two M4 holes. See details.

Place the Spacers

as shown, and x the

front end of the drawer

Sk

runners

2

and 3 using screws

Kf

through the holes

to the sides

number 2 and 8 as indicated.

Sk

by

Nu

ø10 x 9mm Spacer x

Front end

Sk

Cp

ø5 x 11, cc34mm Bolt x

Cp

6

Cp

2

Cp

3

Kf

4

ø5.8 x 19mm Screw x

4

Sk

245 x 17 x 10mm Drawer runner x

Kf

Hole no.

2

Kf

Nu

Sk

Hole no.

2

Nu

8

Sk

See details.

5

Sk

3

Front end

Sk

Hole no.

Nu

Kf

Hole no.

2

8

Kf

Nu

350265-06

Assembly Instructions

Step 1.6

Slide the top of the draw-

Sk

er runners

Place the Spacers

as shown, and x the

back end of the drawer runners

2

and 3 using screws

Kf

through the holes

indicated.

See details.

forwards.

Sk

to the sides

Nu

Kf

ø5.8 x 19mm Screw x

Nu

2

ø10 x 9mm Spacer x

2

Kf

2

Nu

Kf

Nu

3

Step 1.7

Knock the dowels Aa into the holes indicated on the back rail front rail

7

6 and using a small

the

hammer.

Step 1.8

Knock the dowels Aa into the holes indicated on

12

the dividers small hammer.

using a

Aa

7

12

Aa

ø8 x 40mm Wooden dowel x

6

Aa

ø8 x 40mm Wooden dowel x

6

Aa

4

350262-07

Aa

x

2

6

Assembly Instructions

Step 1.9

Slide the top of the drawer

Sk

runner

backwards.

Identify the front end of the

Sk

drawer runner

by the two

M4 holes.

Fix the front end of the

Sk

drawer runner dividers

Kb

12

through the holes

to the

using screws

number 2 and 8 as indicated.

Step 1.10

Slide the top of the drawer

Sk

runner

Fix the back end of the

drawer runner dividers through the hole indicated.

forwards.

Sk

to the

12

using screw Kb

Kb

ø5.8 x 8mm Screw x

Front end

Sk

12

Sk

12

Sk

4

245 x 17 x 10mm Drawer runner x

Kb

Sk

Hole no.

Kb

8

2

Hole no.

Kb

ø5.8 x 8mm Screw x

Kb

2

Step 1.11

Turn the dividers 12 upside down.

Slide the top of the drawer

Sk

runner

forwards.

Fix the front end of the

drawer runner dividers

Kb

through the holes

Sk

to the

12

using screws

number 2 and 8 as indicated.

Step 1.12

Slide the top of the drawer

Sk

runner

Fix the back end of the

drawer runner dividers through the hole indicated.

forwards.

Sk

to the

12

using screw Kb

Kb

ø5.8 x 8mm Screw x

12

Sk

4

Sk

245 x 17 x 10mm Drawer runner x

Kb

Hole no.

Kb

8

Sk

2

12

Hole no.

2

Kb

ø5.8 x 8mm Screw x

Kb

2

7

350265-08

Assembly Instructions

Step 1.13

Screw the bolts Cb into the holes indicated on the

1

top

.

Step 1.14

Place the dividers 12 onto the top

Push cams holes indicated on the dividers pointing towards the top

1.

Ca

12

, arrows

1

.

into the

Cp

ø5 x 11, cc34mm Bolt x

Cp

8

Cp

1

Ca

ø15 x 10.5mm Cam x

4

12

Ca

12

Ca

1

Turn the cams

Ca

to the

right to x the

12

dividers

.

Step 1.15

Place the sides 2 and

3

onto the back rail 6

and the front rail

Push cams holes indicated on the back rail

7.

rail

6

Arrows pointing towards the sides

Turn the cams

right to x the sides

3

and

.

7.

Ca

into the

and the front

2/3

.

Ca

to the

2

Ca

ø15 x 10.5mm Cam x

7

Ca

6

Ca

2

Ca

3

Ca

6

350265-09

8

Assembly Instructions

Step 1.16

Place the sides 2 and

3

onto the top 1.

Push cams

Ca

into the

holes indicated on the

2

sides

and 3.

Arrows pointing towards

1

the top

Turn the cams

right to x the top

.

Ca

to the

.

1

Step 1.17

Fix the back rail 6 and

7

the front rail dividers

12

using screws

to the

as shown,

Dj

.

Ca

ø15 x 10.5mm Cam x

4

2

Ca

3

Ca

1

Dj

ø5 x 38mm Screw x

4

Step 1.18

Important!

The dressing table

!

is heavy.

Lift with care.

Its recommended that the

dressing table is xed to the

wall.

Fh

Use the ttings

the instructions included

with the ttings.

. Follow

12

Dj

12

Dj

7

6

Dj

Fh

Wall strap and instruction x 1

9

350265-10

Assembly Instructions

Step 2

Assembly of the drawers.

Step 2.1

Fix the drawer sides 9

10

to the drawer back shown, using screws

as

Bp

Step 2.2

10

9

11

9

8

x

3

Bp

ø3 x 35mm Screw x

.

Bp

10

Bp

9

x

3

12

9

Ab

Knock the dowels Ab into the holes indicated on the drawer sides

9

using a smal hammer.

Step 2.3

Slide the drawer bottom

11

into the drawer

9

sides

.

Step 2.4

ø6 x 30mm Wooden dowel x

9

Ab

9

Ab

x

3

12

9

x

3

11

Cp

Screw the bolts Cb into the holes indicated on the drawer front

350265-11

8

Cp

.

Cp

8

x

3

ø5 x 11, cc34mm Bolt x

6

10

Assembly Instructions

Step 2.5

Push the drawer front 8 onto the drawer sides

Place cams

Ca

into the holes indicated. Arrow pointing towards the front.

Ca

Turn the cams

to the

right to x the front.

9

.

Step 2.6

Important!

Make sure the

!

angle between

8

the drawer front the drawer sides before the drawer bottom

11

is xed using Fi as

shown. To adjust the angle between the sides and the front push

Fi

the tting

sidewards.

and

9

is 90°

Ca

ø15 x 10.5mm Cam x

6

8

Ca

9

x

9

3

Fi

Back fitting w. ø3.5 x 15mm Screw x

90°

x

3

Fi

6

Fi

Step 2.7

Fix the metal knobs Ge

8

to the drawer front using screws

Hd

.

Step 2.8

Pull out the drawer runners. Slide the drawers onto the runners.

Fix drawers to the drawer

Hk

runners using screws

.

Ge

ø27 x 24mm Metal Knob x

Ge

8

Hd

Hk

Hd

3

M4 x 20mm Screw x

x

3

Hk

M4 x 9mm Screw x

6

Hk

11

350265-12

Osaka 3 Drawer Chest

Assembly Instructions - Please keep for future reference

White 2283935

Black 2487865

Dimensions

:

Width

Depth

Height

40.0 cm

:

40.0 cm

:

59.6 cm

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Argos Customer Helpline: 0845 640 30 30

350266

Issue 1 - 15-05-2014

Safety and Care Advice

!

Important - Please read these instructions fully before starting assembly

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor.

• Parts of the assembly will be easier with 2 people.

• From time to time check that there are no loose screws on this unit.

• We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Dispose of all packaging carefully and responsibly

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

.

Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

1