Argos 205-4528 ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 50cm

Depth - 59cm

Height - 87cm

Valencia - 4 Drawer Cabinet

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 31/07/14

Important - Please read these instructions fully before starting assembly

hygena

656/5848

633/2909

633/2734

205/4528

633/2820

204/6718

R

Cabinet

Black Drawer Pack

Cream Drawer Pack

Oak Drawer Pack

White Gloss Drawer Pack

White HN Drawer Pack

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 16.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2, 3 and 4.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

2

7

4

3

Back (DPF077A)

(479 x 680mm)

6

Base (DPF074A)

(469 x 494mm)

Cross Rail (DPF076A)

(469 x 96mm) x 2

5

Drawer Back (DPF130A)

(439 x 98mm) x 4

Left Side (DPF087A)

(720 x 560mm)

Right Side (DPF088A)

(720 x 560mm)

Drawer Base (DPF129A)

(439 x 448mm) x 4

8

Drawer Front (DPF151B)

(497 x 176mm) x 4

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 10

B

Metal dowel (F901) x 8

C

D

Large locking nut (F900) x 8

F

G H I a

I c

I d

I e

I b

J K

13mm Screw (F63) x 72

E

13mm Screw (F79) x 6

Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2

L M

N O

S

P

Q

R

25mm Screw (F50) x 5

Bracket (F945) x 4

Leg Bracket (F127) x 2

Leg Socket (F120) x 4

Leg Clip (F128) x 2

16mm Screw (F129) x 16

Leg (F122) x 4

13mm Screw (F52) x 48

Left Runner (F139) x 4

L

R

Left Soft Close Unit (F141) x 4

Right Soft Close Unit (F142) x 4

Left Soft Close Catch (F143) x 4

Right Soft Close Catch (F144) x 4

Left Drawer Side (F145) x 4

Right Drawer Side (F146) x 4

L

R

Right Runner (F140) x 4

Door Handle

(F214) x 4

T a

T b

25mm Screw (F132) x 8

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

L

K

L

Fit the left runners to the left side

Fit the 4 left runners marked ‘L’ to the left side .

The 1st screw uses the 2nd hole in from the front of the runner.

The 2nd screw uses the 4th hole in from the back of the runner.

The 3rd screw uses the 8th hole in from the back of the runner.

Fit left soft close units to the left side

Fit the 4 left soft close units . marked ‘L’ to the left side using 3 screws .

1

Step 2

L

K

L

K

L

K

L

K

P

L

P

K

L

K

Assembly Instructions

5

Step 3

Prepare the left side

Screw 4 metal dowels into the holes shown on the left side .

Note: Tighten metal dowels up fully against the panels.

Fit a bracket flush to the top edge of the left side , about 150mm in from the groove, see diagram.

Secure the bracket using screw .

Fit another bracket flush to the back edge of the left side , about 5mm down from the top edge, see diagram.

Secure the bracket using screw .

B

1

J

1

J

1

E

J

E

J

E

B

J

E

L

B

5mm

150mm

J

R

Fit the right runners to the right side

Fit the 4 right runners marked ‘R’ to the right side .

The 1st screw uses the 2nd hole in from the front of the runner.

The 2nd screw uses the 4th hole in from the back of the runner.

The 3rd screw uses the 8th hole in from the back of the runner.

2

K

Q

Step 4

Note: The brackets must be flush with the top/back edge of the panel.

Q

K

Assembly Instructions

6

Step 5

Step 6

R

Fit soft close units to the right side

Fit the 4 right soft close units marked ‘R’ to the right side using 3 screws .

2

K

N

R

2

R

2

Prepare the right side

Screw 4 metal dowels into the holes shown on the right side .

Fit a bracket flush to the top edge of the right side , about 150mm in from the groove, see diagram.

Secure the bracket using screw .

Fit another bracket flush to the back edge of the right side , about 5mm down from the top edge, see diagram.

Secure the bracket using screw .

B

2

J

2

J

2

E

J

E

J

E

B

J

E

R

N

K

Assembly Instructions

7

Step 7

Step 8

A

Prepare the base

Insert 4 large locking nuts into the base as shown.

Note: Arrow on locking nut must point towards hole in edge of panel.

Tap 6 wooden dowels into the base as shown.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

C

3

10mm

A

3

A

C

3

I a I a

I b

b:

a:

c: d:

I a

3

Fit the legs to the base

a: Push the leg sockets

. into the holes in the base as shown.

b: Secure each leg

socket with 3 screws .

c: Tap in the centre plug

on each leg socket .

d: Push the leg into

the leg socket .

I a

I e

3

x 3

I a

I b

R

Assembly Instructions

8

Step 9

Step 10

4

A

C

4

A

C

Prepare the 2 cross rails

Insert 2 large locking nuts into the cross rails as shown.

Tap 2 wooden dowels into the cross rails as shown.

4

A

Finished

front edge

Join the right side and base

Push the base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

B

F

2

3

2

C

Assembly Instructions

9

Step 11

4

Fit the 2 cross rails

Push each cross rail onto the right side .

Use a screwdriver to tighten the large locking nut fitted to each cross rail .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

2

C

4

R

2

4

Support this cross rail until the left side has been fitted in the next step.

R

1

4

Step 12

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the large locking nut fitted to the 2 cross rails and the 2 fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

3

1

C

4

Assembly Instructions

10

Step 13

Step 14

Fit the back

Slide the back along the grooves in the side panels and .

7

1 2

R

7

1

3

2

R

3

F

Secure the back

The bottom edge of the back must be flush with the bottom edge of the base .

Secure the back to the back edge of the base using 3 screws . .

Stand the unit up for the next stage.

7

3

F

7

Assembly Instructions

11

Step 15

Step 16

R

Secure the unit to the wall

Using the brackets fitted to the back edge of the sides and screw the unit to the wall.

Fixings are not supplied as they will need to suit the wall type, and the length of screw will depend on the distance of the back of the Unit to the wall.

F

5mm

Warning: Take care when

drilling the wall

that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

Joining units together

Fittings have been supplied so you are able to join units together.

Make sure that your first unit is level.

Push the other unit up against first unit and ensure both units are level.

Check that the ends are flush and in line, then clamp them together.

Using a 5mm drill bit, drill 2 holes (approximate positions shown circled) in the side panel into the adjoining side panel of the other unit.

Push the connecting sleeves into the holes and then screw the connecting bolts in from the other side.

G

H

G

H

1 2

R

1

2

R

Assembly Instructions

12

Step 17

Step 18

Drill the handle holes in the drawer fronts

Lay the drawer front down onto a soft, smooth surface.

Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any breakout.

Using the pilot holes in the rear face of the drawer front , drill through the holes using a

2.5mm diameter drill.

Turn the drawer front over and open out the

2.5mm holes that you have just drilled by drilling back through them with a 5mm drill.

Note: Drill bits are not provided.

Fit the unit to worktop

To fit the unit to the worktop use 2 screws to screw up through the holes in the cross rail as shown.

Then use 2 screws to screw up through the brackets as shown.

F

E

J

4

R

F

E

8

R

ONLY drill

these 2 holes

Small piece of

waste wood

8

x 4

Assembly Instructions

13

Step 19

Step 20

Step 21

Prepare the drawers

Fit the left drawer side and right side drawer side onto the drawer front using 4 screws . into the slotted holes.

Important: Make sure that the drawer sides and drawer front are the correct way around.

D

S

Top of

drawer

front

Wheel on

outside surface

Wheel on

outside surface

R

8

D

Fit the drawer base

Push the drawer base against the bottom of the drawer sides and .

While holding it in place, secure the drawer base . using 4 screws into the front and back holes, as shown.

D

S

R

6

R S

D

x 4

Fit the drawer back

Push the drawer back up into the drawer assembly.

While holding it in place, secure the drawer back . using 4 screws into the top and bottom holes, as shown.

D

5

D

x 4

Assembly Instructions

Step 22

Step 23

14

Fit the soft close catches

Position the location hole of the right soft close catch marked ‘R’ into the 3rd hole up from the front of the right drawer side then secure using 3 screws .

Position the location hole of the left soft close catch marked ‘L’ into the 3rd hole up from the front of the left drawer side and secure using 3 screws .

L

R

O

M

O

S

R

M

S

R

D

M

D

Location

hole

D

Location

hole

x 4

Fit the handle

Attach the handle supplied with the drawer front using the screw(s) packed with it.

T b

T a

8

T a

8

T b

Assembly Instructions

15

Step 24

Step 25

L N

R

Prepare the soft close units

Before fitting the drawers you will need to push the movable part of the 8 soft close units and forward until it clicks into place.

NL

R

and

NL

and

R

Fit the drawers

Slide the wheels on the drawer sides and over the wheels on the runners and then push the drawer into position.

Important: Make sure that 2 soft close catches on each drawer engage with the soft close units fitted to the side panels.

P Q

R S

and

R S

P Q

Assembly Instructions

16

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Step 26

Fit other products to the unit

To fit other products to this unit e.g. worktops etc., please follow the instructions packed with them.

We recommend that you consult a qualified joiner or kitchen fitter.

Assembly is complete

Warning: The unit is heavy. Lift with care.

R

Fit the plinth

After cutting the plinth to the required length, offer the plinth up to the unit and using a pencil, mark the position of the unit’s legs on the back of the plinth.

Position the leg bracket . so it is in the centre of the pencil mark and half way up the plinth.

Fix the leg bracket to the back of the plinth using 2 screws .

Slide the leg clip into the leg bracket

Offer the plinth up to the unit and push the leg clips onto the legs . .

I b

I c

I d

.

I e

Pencil mark

Plinth

I c

I d

Plinth

I e I e

Step 27

608/2345

608/2369

205/5668

198/9917

608/2352

Black Plinth Pack

Cream Plinth Pack

Oak Plinth Pack

White HN Plinth Pack

White Gloss Plinth Pack

ALR2654

Argos 656-5848, Valencia - 4 Drawer Cabinet, 633-2909, 633-2734, 205-4528 ASSEMBLY INSTRUCTIONS

Specifications and Main Features

Frequently Asked Questions

User Manual