Argo AW726CLF, AW735CL, AW764CL, AW720HL, AW726HL Operating Instructions Manual

...

Download

Page 1

37.4254.031.01 11/2014

AW720HL AW726HL AW726HLF AW735HL AW735HLF AW752HL AW764HL

OPERATING INSTRUCTIONS • ISTRUZIONI D’USO

NOTICE D’UTILISATION • BEDIENUNGSANLEITUNG

INSTRUCCIONES DE USO •

INSTRUCÇÕES DE FUNCIONAMENTO

ΟΟΔΔΗΗΛΛΙΙΕΕΣΣ ΧΧΡΡΗΗΣΣΕΕΩΩΣΣ

Split air conditioner system• Condizionatore d’aria split system •Climatiseurs split

Split-klimagerät• Acondicionador de aire de consola partida sistema split

Aparelho de ar condicionado-Sistema Split

•

ΔΙΑΙΡΟΥΜΕΝΕΣ ΜΟΝΑΔΕΣ ΚΛΙΜΑΣΜΟΥ

COOLING Models

AW726CL AW726CLF AW735CL AW735CLF AW752CL AW764CL

HEAT PUMP Models

COOLING Models

FC735CL FC752CL FC764CL

COOLING Models

AS71CL AS100CL AS125CL

Page 2

This air conditioner is equipped with cooling, dehumidification and fan functions , automatic, cooling, heating, dehumidification and fan functions . Details on these functions are provided below; refer on these descriptions when using the air conditioner.

CONTENTS

NAME OF PARTS AND OPERATION SELECTOR SWITCH 3 INSTALLATION LOCATION 4 ELECTRICAL REQUIREMENTS 4 SAFETY INSTRUCTIONS 4 USING THE REMOTE CONTROL UNIT 4 REMOTE CONTROL UNIT 5 HOW TO SETTHE PRESENTTIME 6 COOLING 6 HEATING 6 AUTOMATIC OPERATION 6 DEHUMIDIFYING (DRY) 6 FAN ONLY 7 ADJUSTING THE FAN SPEED 7 NIGHT MODE 7 SETTING THE TIMER 7 SETTING THE 1 HOUR TIMER 8 ADJUSTING THE AIR FLOW DIRECTION 8 OPERATION WITHOUT THE REMOTE CONTROL UNIT 9 CARE AND CLEANING 10 TIPS FOR ENERGY SAVING 12 TROUBLESHOOTING 12

NOTE

PRODUCT INFORMATION

If you have problems or questions concerning your Air Conditioner, you will need the following information. Model and serial numbers are on the nameplate on the bottom of the air conditioner.

Model No...........................................................................

Serial No............................................................................

Date of purchase...............................................................

Dealer’s address ...............................................................

Phone number ....................................

ALERT SYMBOLS

The following symbols used in this manual, alert you to potentially dangerous conditions to users, service personnel or the appliance:

This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death.

This symbol refers to a hazard or unsafe practice which can result in personal injury or product or property damage.

WARNING

CAUTION

COOLING Models

HEAT PUMP Models

DECLARA

TION OF CONFORMITY

This product is marked as it satisfies Directives:

–Low voltage no. 2006/95/EC.

(Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A1 1:2004 + A12:2005 + A13:2012 + A1:2006 + A2:2009 con EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 + A15:201 1).

– Electromagnetic compatibility no. 2004/108/EC, 92/31 EEC and 93/68 EEC.

(Standard: EN55014-1 (2006) +

A1(2009) + A2(2011), EN 55014-2 (1997) + A1(2001) + A2 (2008), EN 61000-3-2 (2006) + A1(2009) + A2(2009), EN 61000-3-3 (2008)

–RoHS2 no.2011/65/EU. –Regulation (EU) no. 206/2012, of 6 march 2012, concerning the specifications for ecodesign requirements of air

conditioners and fans.

–Regulation (EU) no. 626/2011, of 4 may 2011, concerning the labeling indicating the energy consumption of air

conditioners.

This declaration will become void in case of misuse and/or non observance though partial of manufacturer's installation and/or operating instructions.

Page 3

8. STANDBY lamp: This lamp lights up when the air conditioner is connected to the power and ready to receive the remote control command.

9. TIMER lamp: This lamp lights up when the system is being controlled by the timer.

10.Air intake latch, on two sides.

11.Air filter.

12.Suspension brackets.

13.Refrigerant couplings.

14.Condensate drain connection.

15.Sensor: Detects the room temperature around the unit;

when the remote control unit is not active the air conditioner will be set by the detected temperature.

1. Remote control unit.

2. Remote control sensor: Detects the room temperature

around the remote control unit, the air conditioner is controlled accordingly.

3. Air outlet: Conditioned air is blown out of the air conditioner through the air outlet.

Air intake: Air from the room is drawn into this section

and passes through air filter which removes dust.

5. Remote control receiver: This section picks up infrared signals from the remote control unit (Transmitter).

6. Operation selector (without remote control): Push the button to walk through the operation modes:

OFF and COOL OFF, COOLand HEAT

7. OPERATION lamp:This lamp lights up during operation. It blinks once to announce that the remote control signal

has been received and stored. It blinks continuously during the protection modes (defrosting, etc.).

The OFF position does not disconnect the power. Use the main power switch to turn off power completely.

WARNING

5 7

9 8

798

NAME OF PARTS AND OPERATION SELECTOR SWITCH

NOTE

The blinking of OPERATION, TIMER and STANDBY lamps, indicates that the operating mode selected is not compatible with the unit. If this happen the air conditioner does not operate until the correct mode is selected.

COOLING Models HEAT PUMP Models

COOLING Models

only

Page 4

SAFETY INSTRUCTIONS

Read this booklet carefully before using this air conditioner. If you still have any difficulties or problems, consult your dealer for help.

This air conditioner is designed to give you comfortable room conditions. Use this only for its intended purpose as described in this Instruction Manual.

Never use or store gasoline or other flammable vapor or liquid near the air conditioner. It is very dangerous.

Never install electrical equipment, which is not protected with IPX1 protection (protection against vertical water drop), under the unit.

The manufacturer assumes no responsabilities if the safety regulations or local codes are not observed.

Never use the power main switch to start or stop the air conditioner: always use the ON/OFF button on the remote control unit or the selector switch on the unit.

Do not stick anything into the air outlet of the air conditioner. This is dangerous because the fan is rotating at high speed.

Do not let children play with the air conditioner.

Do not cool the room too much if babies or invalids are present.

WARNING

CAUTION

INSTALLATION LOCATION

We recommend this air conditioner to be installed properly by qualified installation technicians in accordance with the installation instructions provided with the unit.

Do not install this air conditioner where there are fumes or flammable gases, or in an extremely humid space such as a green house.

Do not install the air conditioner where excessively high heat-generating objects are placed.

Do not install the air conditioner where the atmosphere is extremely damp or humid (e.g. greenhouse or laundry) it could be wetted by drops of water (i.e. in laundries).

T o protect the air conditioner from heavy corrosion, avoid installing the outdoor unit where salty sea water can splash directly onto it or in sulphurous air near a spa.

WARNING

ELETRICAL REQUIREMENTS

Before installation, check that the voltage of the electric supply in your home or office is the same as the voltage shown on the nameplate.

All wiring must conform to the local electrical codes. Consult your dealer or a qualified electrician for details.

Each unit must be properly grounded with a ground (or earth) wire or through the supply wiring.

Wiring must be done by a qualified electrician.

HOW TO INSTALL BATTERIES

l Remove trhe lid in the rear part of the remote control unit

and check the settings of the four microswitches as shown below:

TEMPERATURE SENSOR SELECTOR

Under normal conditions the room temperature is detected and checked by the temperature sensor placed in the remote controller (I FEEL icon displayed ).This function is designed to provide a confortable room temperature by transmitting the temperature control command from the location next to you. Therefore, when using this function, the remote control should always be pointed at the air conditioner.

It is possible to disable the remote controller room sensor pressing the I FEEL button. In this case the I FEEL icon on the remote controller display lights off and the sensor placed in the air conditioner becomes active.

USING THE REMOTE CONTROL UNIT

Insert two AAA alkaline batteries of 1,5 V-DC making sure that point in the direction marked in the battery compartment.The displayed time flashes. Press the SEL TYPE button. Remote controller is now ready for operation.

The batteries last about six months. Depending on how much you use the remote control unit. Remove the batteries if you do not use the remote control unit for more than one month. Replace the batteries when the remote control unit lamp fails to light, or when the air conditioner does not receive the remote control unit signals.

The batteries of the remote control contain polluted substances. Exhausted batteries must be disposed according to the laws in force.

OPERATION WITH THE REMOTE CONTROL UNIT

When using the remote control unit, always point the unit transmitter head directly at the air conditioner receiver.

HOW TO TURN ON THE AIR CONDITIONER

Press the ON/OFF button to turn the air conditioner on. The operation lamp will light up, indicating the unit is in operation.

The remote control unit sends the temperature signal at any key pressing and automatically every five minutes. If, due to some troubles, the signal from the remote control is no longer detected, the air conditioner keeps operating using the temperature sensor of the indoor unit to control the room temperature. In this case, the temperature around the remote control unit may differ from the temperature detected in the air conditioner position.

NOTE

SWITCHES

Page 5

REMOTE CONTROL UNIT

“NIGHT” BUTTON

For details, see "NIGHT MODE". When you press this button in the COOL, HEAT or DRY mode, the mark appears on the display and the microcomputer in the remote control unit will adjust the set temperature to save energy.

TRANSMITTER

When you press the buttons of the remote control unit, the mark appears on the display to transmit the setting changes to the receiver in the air conditioner.

TIMER AND PRESENT TIME SETTING BUTTONS

With these buttons is possible to set the clock and the timer. For details refer to paragraphs “ SETTING THE HOUR” and “SETTING THE TIMER2.

“TIMER SEL” BUTTON

Press this button to select the type of timer to activate. For details refer to paragraph “SETTING THE TIMER”.

DISPLAY

Information is displayed when the remote controller is switched on. If switched off, only the operating mode, the room temperature and the clock are shown

Operation mode

Fan speed

High speed

Automatic

Medium speed

Low speed

Displayed when transmitting data

Set point temperature

I FEEL mode is active (remote controller sensor active)

Timer modes

Automatic *

Cooling Heating

Dehumidification Fan

MODE SELECTOR BUTTON

Press this button to modify the air conditioner mode.

(automatic) *

When this setting is selected, the air conditioner calculates the difference between the thermostat setting and the room temperature and automatically switches to the "cool" or "heat" mode.

(heating) *

The air conditioner makes the room warmer.

(dry)

The air conditioner reduces the humidity in the room.

(cooling)

The air conditioner makes the room cooler.

(fan)

The air conditioner works only as a circulation fan.

Clock

Room temperature

Night mode

Oscillation Flap

INACTIVE BUTTONS

TEMPERATURE SETTING BUTTONS TEMP - (cooler)

Press this button to decrease the set temperature.

TEMP + (warmer)

Press this button to increase the set temperature.

SENSOR

A temperature sensor inside the remote control unit detects the room temperature.

“SEL TYPE” BUTTON

Press this button in order to:

• set the clock

• set the ON/OFF timer For details refer to paragraphs “SETTING THE HOUR” and “SETTING THE TIMER”.

TEMPERATURE SENSOR SELECTOR

Press the I FEEL button to modify the active setting for room temperature detection (from remote controller to air conditioner and viceversa)

“FAN “ BUTTON

Fan speed is automatically selected by the microcomputer.

High speed. Medium speed.

Low speed.

ON/OFF BUTTON

This button turns the air conditioner ON and OFF.

PUSH-BUTTON FLAP

To press this push-button in order to select the wished function.

Fixed: six position

Continous oscillations

Automatically oscillations

* only

HEAT PUMP Models

Page 6

1.Set the MODE button to DRY. The icon is displayed.

2.Press the ON/OFF button and switch the air condioner

ON.

3.Press the TEMP. buttons to set the desired temperature (the temperature range is between 32 °C max. and 16 °C min.).

HOW TO SET THE PRESENT TIME

COOLING

HEA TING only

1. Press the button SEL TYPE three times.

The time indication alone flashes.

2. Press the SET H button until the present time hour is displayed. Press the SET M button until the present time minutes are displayed. The display will automatically stop flashing.

THE DISPLAYSHOWS THE SELECTED TEMPERATURE.

AFTER 5 SECONDS FROM THE REQUIRED TEMPERATURE SETTING THE DISPLAY WILL SHOW THE ROOM TEMPERATURE AGAIN.

4.Press the FAN button to select the fan speed.

ONON ON

Δ 1 H Δ 1 H

MIN. MAX.

A B

C C

27 26 25 24

23 22

21 20 19

Verify that the unit is connected to the main power and the STANDBY lamp is light up.

1.Set the MODE selector to COOL .

2.Press the ON/OFF button and switch the

air condioner ON.

3.Press the TEMP. buttons to set the desired

temperature (the temperature range is between 32 °C max. and 16 °C min.).

NOTE

1.Set the MODE selector to HEAT .

2.Press the ON/OFF button and switch the air condioner ON.

3.Press the TEMP . buttons to set the desired temperature (the

temperature range is between 32 °C max. and 16 °C min.).

THE DISPLAY SHOWS THE SELECTED TEMPERA TURE.

AFTER 5 SECONDS FROM THE REQUIRED TEMPERATURE SETTING THE DISPLAY WILL SHOW THE ROOM TEMPERA TURE AGAIN.

4.Press the FAN button to select the fan speed.

For several minutes after the start of heating operation, the indoor fan speed will be low until the indoor heat exchanger coil has warmed up sufficiently . This is because the COLD DRAFT PREVENTION SYSTEM is operating. During this period, the STANDBY lamp remains lit.

NOTE

DEFROSTING OF OUTDOOR UNIT HEAT EXCHANGER

When the outdoor temperature is low, frost or ice may appear on the heat exchanger coil, reducing the heating performance. When this happens, a microcomputer defrosting system operates. At the same time, the fan in the indoor unit stops and the ST ANDBYlamp remains lit until defrosting is completed. Heating operation restarts after several minutes. (This interval will vary slightly depending on the room and outdoor temperature).

HEATING PERFORMANCE

Aheat pump conditioner heats a room by taking heat from outside air. The heating efficiency will fall off when the outdoor temperature is very low. If enough heat is not obtained with this air conditioner, use another heating appliance in conjunction with it.

1.Set the MODE selector to AUTO .

2.Press the ON/OFF button and switch the air condioner

ON.

3.Press the TEMP. buttons to set the desired temperature (the temperature range is between 32 °C max. and 16 °C min.).

When this setting is selected, the air conditioner calculates the difference between the thermostat setting and the room temperature and automatically switches to the COOL or HEA Tmode as appropriate.

4.Press the FAN selector button to the setting you want.

THE DISPLAY SHOWS THE SELECTED TEMPERA TURE.

AFTER 5 SECONDS FROM THE REQUIRED TEMPERATURE SETTING THE DISPLAY WILL SHOW THE ROOM TEMPERA TURE AGAIN.

Example of operation diagram in the (Auto) mode with the set room temperature at 23°C.

NOTE

The air conditioner changes the operation mode (from cool to heat or vice versa, if one of the following conditions occurs:

- ZONE A: changes if the difference between the room

temperature and the temperature set on the remote control unit is at least 3°C.

- ZONE B: changes if the difference between the room

temperature and the temperature set on the remote control unit is at least 1°C, one hour after the compressor stop.

- ZONE C: never changes if the difference between the

room temperature and the temperature set on the remote control unit is no more than 1°C.

DEHUMIDIFYING (DRY)

THE DISPLAY SHOWS THE SELECTED TEMPERA TURE.

AFTER 5 SECONDS FROM THE REQUIRED TEMPERATURE SETTING THE DISPLAY WILL SHOW THE ROOM TEMPERA TURE AGAIN.

HEAT PUMP Models

AUTOMATIC OPERATION

only

Page 7

WHEN DIFFERENCE BETWEEN

ROOM TEMPERATURE AND SET FAN SPEED

TEMPERATURE IS

Cooling and 2 °C and over High dehumidifying Between 2 and 1 °C Medium modes: Below 1 °C Low

2 °C and over High

Heating mode:

Below 2 °C Medium

ADJUSTING THE FAN SPEED

AUTOMATIC

Simply set the FAN selector to the position.A microcomputer automatically controls the fan speed when the AUT O mode is selected. When the air conditioner starts operating, the difference between the room temperature and the set temperature is detected by the microcomputer which then automatically switches the fan speed to the most suitable level.

NIGHT MODE

The NIGHT mode enables you to save energy.

1. Set the MODE selector to cool, dry or heat.

2. Press the NIGHT button.

3. The mark appears on the display. Press the NIGHT

button again to release the NIGHT function.

What does the NIGHT mode mean?

In this mode, the air conditioner will cool or heat the room to the set temperature, and then the thermostat will make the unit pause. After about 1 hour, the air conditioner will automatically reset the set temperature as follows (also refer to graphs).

OPERATING MODE SET TEMPERATURE CHANGE

Heating Lowered by 1 °C

Cooling and Dehumidifying Raised by 1 °C

When the room temperature reaches the new set value, the thermostat will cause the unit to pause. After about 1 hour the temperature will be raised by 1 °C in cooling, or lowered by 1 °C in heating. This enables you to save energy without sacrificing your comfort.

FAN ONLY

If you want to make air circulate without any temperature control, follow these steps:

1. Press the ON/OFF operation button and switch the air conditioner ON.

2. Press MODE button until only the fan sign appears on the display.

The above mentioned data make reference to the air conditioner operating when the sensor on the remote control unit is ON. (Refer to temperature sensor selector). If the sensor on the indoor unit is being used then actual operation will slightly differ from that described in the above tables. The automatic speed is not available in FAN ONLY mode.

High speed Med. speed Low speed

MANUAL

If you want to manually adjust speed just set the FAN selector as desired.

NOTE

A)HOW TO SET THE ON TIME

Press the SEL TYPE button once. The ON and time indications flash.

2. Press the SET H button until the designed hour is displayed. Press the SET M button until the designed minutes are displayed. The display will change automatically back to show the present time after 10 sec.

3. Press the ON/OFF button to start the air conditioner.

4. Press the TIMER SEL button to activate the ON timer.

B) HOW TO SET THE OFF TIME

1. Press the SEL TYPE button twice.

The OFF and time indications flash.

3. Press the ON/OFF button to start the air conditioner.

4. Press the TIMER SEL button two times to activate the OFF timer.

C) HOW TO SET A PROGRAM FOR

DAILY ON/OFF OPERATION (OR VICEVERSA)

1. Set the timer ON/OFF as shown in A)

and B).

2. Press the ON/OFF button to start the air conditioner.

3. Press three times the TIMER SELECT button to activate the DAILY timer.

SETTING THE TIMER

After timer setting, press PROGRAM button in order to check the ON/OFF setting time.

NOTE

Use DRYoperation when you want to reduce the humidity in the room.

Once the room temperature reaches the set level, the unit repeats the cycle of turning on and off automatically.

During DRYoperation, the fan speed is automatically set to or stops to prevent overcooling.

Dry operation is not possible if the indoor temperature is 15 °C or less.

1°C

1 hour

1 hour TIME

Setting temperature

Room temperature

COOLING AND DEHUMIDIFYING

1°C

1 hour

1 hour TIME

Setting temperature Room temperature

HEATING

Page 8

VERTICAL (with remote control unit)

Press the FLAP button to select the flap function:

HORIZONTAL (manual) - Only for AW-FC models

The horizontal air flow can be adjusted by moving the vertical vanes to the left or right, as indicated in the following figures.

ADJUSTING THE AIR FLOW DIRECTION

Do not move the flap with your hands when the air conditioner is running.

CAUTION

Left

Vertical vane

Right

FC MODELS

AW MODELS

AS MODELS

FLAPS

Use the FLAP button on the remote control to adjust the position of the flap. If you move the flap by hand, the factual flap position and the flap position on the remote control may no longer match. If this should happen, shut off the unit, wait for the flap to close, and then turn on the unit again; the flap position will now be normal again.

Do not have the flap pointed down during cooling operation. Condensation may begin to form around the air vent and drip down.

CAUTION

AW MODELS

FC MODELS

VERTICAL VANE

Fixed:

six

position

Continous

oscillations

Automatically

oscillations

Down

Flap

Air outlet

grille

DEFLETTORE

NOTES

The flap automatically closes when the unit is off.

When the unit starts in heating operation, the fan speed will be low and the flap will be in the 4position until the air being blown out of the unit begins to warm. Once the air warms up, the flap position and fan speed change to the settings specified with the remote control.

TIMER SETTING PROCEDURE.

Press four times the TIMER SEL button.The 1 HOUR TIMER mark will appear on the display.

CANCELLATION PROCEDURE

Press the ON/OFF button to turn the air conditioner off.

Wait for the indoor unit to stop operating.

Press the ON/OFF button again to turn the air conditioner on.

SETTING THE 1 HOUR TIMER

This function causes the unit to operate for one hour at the set conditions, regardless of whether the unit is on or off.

Page 9

40°

50°

Set vertical vanes to the front position during COOLING/DRY operation if humidity is high. If the vertical vanes are set to the left-most or right-most position, condensation will form around the air outlet and drip off.

CAUTION

Zone «A»

for cooling and dehumidifyng

Zone «B»

for heating

40°

50°

«B»

«A»

«B»

«A»

(ONLY AW- FC MODELS)

2. WHEN THE AIR CONDITIONER IS RUNNING

If you want to turn off the air conditioner push the operation selector with a pen until the OPERA TION lamp is turned off.

Power failure during operation.

In the event of power failure, the unit will stop. When the power is resumed, the unit will restart automatically after 3 minutes.

NOTE

If you have lost the remote control unit or it has troubles, follow the steps below.

1. WHEN THE AIR CONDITIONER IS STOPPED

If you want to turn on the air conditioner push the operation selector with a pen to select the desired mode (COOL or HEAT).

OPERATION WITHOUT THE REMOTE CONTROL UNIT

The air conditioner will start in HIGH fan speed. The temperature setting is 25°C for cooling mode and 21°C for heating mode.

NOTE

HOW TO ADJUST THE FLAP DIRECTION

Zone «A» for cooling

and dehumidifyng

Zone «B»

for heating

OPERATION SELECTOR

AW MODELS

FC MODELS

OPERATION SELECTOR

AS MODELS

OPERATION SELECTOR

W MODELS

FC MODELS

AS MODELS

Zone «A»

for cooling and dehumidifyng

Zone «B»

for heating

Page 10

AS MODELS

GRILLE

STRING

Detach the safety string from the frame (remember to attach it again after cleaning or maintenance).

Open the air intake grille

, hold it on and pull it toward

you to detach the two guides.

CONDENSATE DRAIN PAN

The inspection or replacement of internal components involve the removal of the condensate drain pan.

Some metal edges and the vanes of heat exchanger are sharp and may cause injury if handled improperly; be especially careful when you clean these parts.

CAUTION

HOW TO REMOVE THE CONDENSATE DRAIN PAN

RUBBER CORK

CONNECTORS

CLIPS (2)

SUPPORT PLATE (2)

SCREW (4)

SPECIAL SCREW (4)

1.Open the air intake grille.

2.Drain the condensate water into a bucket trough the

rubber cork that should be soon closed.

3.Remove the frame-grille assembly by loosening the four

special screws with washer; you can utilise the two clips that fix the frame to the unit.

4.Disconnect the electrical connectors between the frame-

grille assembly and the unit.

5.Remove the four screws of the two support plates.

6.Grasp the two support plates, remove with care the

condensate drain pan and clean it inside, if necessary.

7.Once finished the maintenance, reassemble the pan,

aligning the side with the hole for condensate drain and the side with the pump; insert the connectors of the unit into the proper hole in the pan.

8.Fix again the four screws of the support plates and the

frame group aligning the corner from which the wires exit and the corner with the connectors of the unit.

9.Mount the air intake grille along with the filter; be sure

that the safety string has been attached and that the latch screw has been fixed on both sides.

ADDITIONAL MAINTENANCE (ONLYFOR AS MODELS)

CARE AND CLEANING

Maintenance operations must be carried out by specially trained personnel.

For safety , be sure to turn the air conditioner off and also to disconnect the power before cleaning.

Do not pour water on the indoor unit to clean it. This will damage the internal components and cause an electric shock hazard.

WARNING

The air intake grille can be removed in order to wash it with water.

AW MODELS

Washing the grille with water

Clean the grille gently using a soft sponge, or the like. Then wipe away any remaining moisture.

Neutral detergent may be used to remove stubborn dirt. Then rinse thoroughly with water and wipe away any remaining moisture.

Arm

Air intake grille

CASING AND GRILLE (INDOOR UNIT)

Clean the casing and grille of the indoor unit with a vacuum cleaner brush, or wipe them with a clean, soft cloth. If these parts are stained, use a clean cloth moistened with a mild liquid detergent. When cleaning the grille, be careful not to force the vanes out of place.

l Never use solvents, or harsh chemicals when cleaning the

indoor unit. Do not wipe the plastic casing using very hot water.

l Some metal edges and the vanes are sharp and may

cause injury if handled improperly; be especially careful when you clean these parts.

l The internal coil and other components of the outdoor

unit must be cleaned every year. Consult your dealer or service centre.

CAUTION

HOW TO REMOVE THE AIR INTAKE GRILLE (ONLY FOR AW -AS MODELS)

With the air intake grille open all the way, grip both arms with your hans and pull toward you to remove.

To remount, hold the air intake grille roughly horizontal and push it in until the arm shafts fit into the indentations in the main unit, then fit the grille into place.

Page 11

HOW TO REMOVE THE FILTER

1.Grasp both ends of the air intake grille and pull to open

it.

2.Hold the air filter by the tab and pull it upward. Clean the air filter.

3.When replacing the filter, make sure that the FRONT mark is facing you. Reinsert the filter into place and close the air intake grille.

AIR FILTER

The filter behind the air intake grille should be checked and cleaned at least once every two weeks. (AW-FC MODELS)

HOW TO REMOVE THE FILTER

1. Grasp both ends of the air intake grille and pull it towards

you and up.

2. Push the filter up slightly, and then pull it down. Clean the

air filter.

Air intake

grille

Insert into the groove on the unit

Air filter

Air intake grille

Air filter

HOW TO REPLACE THE FILTER

1. With the «FRONT» mark facing you, slide the filter up

into the unit and then lower the handler into the groove on the unit.

2. After installing the filter, press the locations marked by the arrows ( ) and close the air intake grille.

AW MODELS

FILTER CLEANING

Use a vacuum cleaner to remove light dust. If there is sticky dust on the filter, wash the filter in lukewarm, soapy water, rinse it in clean water, and dry it.

1.Remove the screw on each side out of the latch using a screwdriver.

2.Press on the two latches of the air intake grille with your thumbs in the direction of the arrow to open the grille.

3.Open the air intake grille downward.

4.Remove the air filter from the air intake grille. Clean the

air filter.

5.Insert the filter correctly again inside the grille, close the grille letting the latches slide toward the outside and fix again the latch with the screw on both sides.

The air filter should be cleaned at least once every six months or more frequently; it depends on the real operation conditions.

HOW TO REMOVE THE FILTER

LATCH

SCREW

AIR INTAKE GRILLE

AIR FILTER

AS MODELS

FC MODELS

FRONT

Page 12

TIPS FOR ENERGY SAVING

DO NOT:

Block the air intake and outlet of the unit. If they are obstructed, the unit will not work well, and may be damaged.

Let direct sunlight into the room. Use sunshades, blind or curtain.

DO:

Always try to keep the air filter clean. A clogged filter will impair the performance of the unit.

T o prevent conditioned air from escaping, keep windows, doors and any other openings closed.

WARNING

• The use of portable telephones near the air conditioner

may cause disturbance to its normal operation and must be avoided. In case abnormal operation is noticed, (OPR operation lamp lights but the air conditioner will not run) to restore normal operation turn-off electric supply for 60 seconds at least, by disconnecting the main switch or the wall plug, then start again the air conditioner.

• If your air conditioner does not work properly , first check

the following points before requesting service. If it still does not work properly, contact your dealer or service centre.

TROUBLESHOOTING

ACTIVATED CARBON AIR FILTER INSTALLATION PROCEDURE

1. Open the unit intake air grille and pull out the standard

air filter.

2. Apply on the rear side of the filter the two spings supplied

with the accessory.

3. Fix the activated carbon filter by the springs.

4. Insert the two air filters one over the other and close

the intake grille.

REAR SIDE OF AIR FILTER

SPRING

ACTIVATED CARBON FILTER

ACTIVATED CARBON AIR FILTER (ACCESSORY SUPPLIED ON REQUEST ONLY FOR AW - FC MODELS)

AW MODELS

This activated carbon air filter cannot remove harmful gases or vapors nor ventilate air in the room. Y ou must open doors or windows frequently when you use gas or oil heating appliances. Otherwise there is a risk of suffocation in an extreme case.

NOTE

1.Two activated carbon air filters for one indoor unit are in

this polyethylene bag.

2.Open the bag just before installing the activated carbon air filters, if not the deodorizing effect durability of the filter may be decreased.

ACTIVATED CARBON AIR FILTER INSTALLATION PROCEDURE

The activated carbon air filterneeds to be installed behind the air filter.

1.Remove the air filter.

2.Install the air clean filter in the position shown in the figure

with the symbol "FRONT" facing you.

3.Reinstall the air filter.

Activated carbon

air filter

Activated carbon air filter

Front: white Rear: black

REPLACEMENT OF ACTIVA TED CARBON AIR FILTER

The filter is disposable.

Do not throw away the filter frame.

The used filter cannot be reused even after cleaning up.

Obtain the filters for replacement at your nearest dealer.

Check the state of dirtiness at least once every two weeks.

Replace the filter after six months’ operation.

WARNING

FC MODELS

The activated carbon air filter is to be added to the standard filter.

It is made of two layers:

- the first layer consists in a synthetic honey comb high

efficiency media to remove the dust and purifing the air.

- the second layer in charcoal media deodorizing the

ambient air.

NOTE

COOLING Models

only

Page 13

Trouble: The air conditioner does not run at all. Possible cause:

1. Power failure.

2. Leakage breaker tripped.

3. Line voltage is too low.

4. Operation button is OFF.

5. Batteries in remote control unit have run down.

Remedy:

1. Restore power.

2. Contact service centre.

3. Consult your electrician or dealer.

4. Press the button again.

5. Replace batteries.

Trouble: The air conditioner does not operate and STANDBY lamp flashes .

Possible cause:

1. Defective sensor.

Remedy:

1. Contact service centre.

Trouble:ST ANDBYand OPERA TION lamps flash and the air conditioner does not operate.

Possible cause:

1. Air conditioner coil sensor defective.

Remedy:

1. Contact service centre.

Trouble: Poor cooling or heating performance. Possible cause:

1. Dirty or clogged air filters.

2. Heat source or many people in room.

3. Doors and/or windows are open.

4. Obstacle near air intake or air discharge port.

5. The set temperature on the remote control unit is too high.

6. Outdoor temperature is too low (heat pump version).

7. Defrosting system does not work (heat pump version).

Remedy:

1. Clean air filters to improve airflow.

2. Eliminate heat source if possible.

3. Shut them to keep the heat or cold out.

4. Remove it to ensure good airflow.

5. Set the right temperature on the remote control unit.

6. Try to use a back-up heater.

7. Consult your dealer.

Trouble: Compressor runs but soon stops. Possible cause:

1. Obstruction of the air intake grilles.

Remedy:

1. Remove obstruction.

Trouble: Clicking sound is heard from the air conditioner. Possible cause:

1. In heating or cooling operation, any plastic parts may expand or shrink due to a sudden temperature change. In this event, a clicking sound may occur.

Remedy:

1. This is normal, and the sound will disappear when an even temperature is settled.

INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE EUROPEAN DIRECTIVE 2012/19/EU

At the end of its working life this equipment must not be disposed of as an household waste. It must be taken to special local community waste collection centres or to a dealer providing this service. Disposing of an electrical and electronic equipment separately avoids possible negative effects on the environment and human health deriving from an inappropriate disposal and enables its components to be recovered and recycled to obtain significant savings in energy and resources. In order to underline the duty to dispose of this equipment separately , the product is marked with a crossed-out dustbin.

INFORMATION FOR CORRECT DISPOSAL OF THE BATTERY IN ACCORDANCE WITH THE EUROPEAN DIRECTIVE 2006/66/EC

Please replace battery when its electricity charge is used up: please do not eliminate this battery together with normal household waste. It must be taken to special local community waste collection centres or to a dealer providing this service. Disposing of a battery separately avoids possible negative effects on the environment and human health deriving from an inappropriate disposal and enables its components to be recovered and recycled to obtain significant savings in energy and resources. In order to underline the duty to dispose of this equipment separately, the battery is marked with a crossed-out dustbin.

REGULATION (EU) No. 517/2014 - F-GAS

The unit contains R410A, a fluorinated greenhouse gas with a global warming potential (GWP) of

2087.50. Do not release R410A into the atmosphere.

Page 14

HOW TO REMOVE BATTERIES

l Remove the lid. l Press the battery toward the negative end and lift it out by its

positive end (as shown in the figure).

l Remove the other battery in the same way.

COME RIMUOVERE LE BATTERIE

l Rimuovere il coperchio. l Premere la batteria verso il polo negativo ed estrarla dalla parte del

polo positivo (come mostrato in figura).

l Rimuovere l’altra batteria allo stesso modo.

COMMENT ENLEVER LES PILES

l Enlever le couvercle. l Pousser la pile vers le pôle négatif et enlever le pôle positif (comme

représenté dans la figure).

l Enlever l’autre pile de la même manière.

WIE DIE BATTERIEN ZU ENTFERNEN

l Die Abdeckung entfernen. l Drucken Sie die Batterie nach dem negativen Pol und entfernen Sie sie vom positiven Pol (wie in Abbildung

gezeigt ist).

l Entfernen Sie ebenso die andere Batterie.

COMO REMOVER LAS PILAS

l Remover la tapa. l Apretar la pila hacia el polo negativo y remover el polo positivo (como en figura). l Remover así también la otra pila.

COMO REMOVER AS PILHAS

l Remover a tampa. l Premir a pilha para o polo negativo e remover a parte do polo positivo (como indicado na figura). l Remover a outra pilha ao mesmo modo.

¶ø™ ¡∞ ∞º∞πƒ∂™∂Δ∂ Δπ™ ª¶∞Δ∞ƒπ∂™

l ¶И¤ЫЩВ ЩЛУ М·Щ·Ъ›· ЪФ˜ ЩФУ ·ЪУЛЩИОﬁ ﬁПФ О·И ·К·ИЪ¤ЫЩВ ЩЛУ ·ﬁ ЩЛ МВЪИ¿ ЩФ˘ ıВЩИОФ‡ ﬁПФ˘ (ﬁˆ˜

Ê·›ÓÂÙ·È ÛÙËÓ ÂÈÎﬁÓ·).

l ∞Ê·ÈÚ¤ÛÙÂ ÙËÓ ¿ÏÏË Ì·Ù·Ú›· ÌÂ ÙÔÓ ›‰ÈÔ ÙÚﬁÔ.

Page 15

Page 16

Via Varese, 90 - 21013 Gallarate - Va - Italy

Tel. +39 0331 755111 - Fax +39 0331 776240

www.argoclima.com