Arecont Vision D4F-AV1115DNv1-3312, D4F-AV2115v1-3312, D4F-AV3115DNv1-3312, D4F-AV5115v1-3312, D4S-AV1115v1-3312 Installation Manual
...Page 1
Arecont Vision D4S/D4F Installation Manual
0 | Page
Page 2
Arecont Vision D4S/D4F Installation Manual
D4S/D4F Indoor Dome Installation Manual
Inside the box:
A. Mounting template
B. Arecont Vision D4S (Image 1-1) or
D4F (Image 1-2)
C. Pack of three (3) wood screws and three
(3) dry wall anchors (D4S only)
Not included but needed:
• #0 Phillips head screwdriver
• #1 Phillips head screwdriver
A
Image 1-1 D4S Indoor Dome
B
A B
Mounting the Camera:
1. Remove camera and hardware from the
box.
2. Use the Mounting template, prepare the
mounting provisions for camera
installation.
3. Use #0 Philips head screwdriver to
loosen the set screw to release the dome
cover (Image 2-1 and 2-2). NOTE: Do
not remove screw from the dome cover.
C
Image 2-1 D4S
Image 1-2 D4F Indoor Dome
Image 2-2 D4F
1 | Page
Page 3
Arecont Vision D4S/D4F Installation Manual
4. Remove D4S or D4F dome cover by rotating
counterclockwise as show in Image 3-1 and
3-2.
5. Run Ethernet cable through the hole on the
bottom of D4S or D4F and plug it into the
RJ45 port on AV’s H.264 compact
MegaVideo
®
camera. (Image 4-1 and 4-2)
Image 3-1 D4S
Image 3-2 D4F
Image 4-1 D4S
Image 4-2 D4F
2 | Page
Page 4
Arecont Vision D4S/D4F Installation Manual
6.1 For D4S models, align the mounting holes in
the dome with the prepared holes on the
mounting surface. Attach D4S to the
mounting surface with the wood screws or
any optional hardware suitable for the
mounting surface. (Image 5)
Adjusting the Tilt and Pan:
7. To adjust the tilt, use a #1 Phillips screwdriver
to loosen the screw on the side of the plastic
U bracket 1/4 turn (Image 7-1 and 7-2).
CAUTION: Do not remove the screw!
90°
0°
Screw
Image 5
6.2 For D4F models, insert D4F into the prepared
hole in the ceiling or wall then tighten the
three “lever screws” by rotating clockwise until
the D4F is firmly installed, as shown in Image
6. The “Support Arm” will ride down the screw
to compress to the mounting surface. NOTE:
Do not over-torque the lever screws.
Support
Arm
Lever
screw
Image 6
Image 7-1 D4S
90°
20°
Screw
Image 7-2 D4F
3 | Page
Page 5
Arecont Vision D4S/D4F Installation Manual
8. Adjust lens tilt as required and tighten the
screw. CAUTION: Please attach camera at
the end of the slot of U bracket to avoid
interference between bubble and lens .
(Image 8)
Image 8
NOTE: Push cable to make camera tilt easier,
if getting caught on housing plastic.
(Image9-1 and 9-2)
Image 9-1 D4S
Image 9-2 D4F
9. To adjust the pan, hold and turn the U bracket
as shown in Image 10.
Pan=360°
Image 10
4 | Page
Page 6
Arecont Vision D4S/D4F Installation Manual
Adjusting the Focus:
10. To focus the lens, loosen the three set screws
as shown in Image 11 and adjust each as
needed. A adjusts the zoom, B adjusts the
iris, C adjusts the focus.
B
Note: Adjust zoom first then focus!
Note: For more information on proper
focusing technique, please watch the
“Focusing Arecont Vision Megapixel
Cameras” Best Practices Training Video at
www.youtube.com/ArecontVision.
11. Secure the dome cover to the camera.
12. Tighten the set screw on the dome cover.
13. Rotate bubble to align camera with slot in
camera shield.
14. Remove the protective film from the camera
dome. NOTE: be cautious not to scratch the
vandal dome cover.
A
C
Image 11
5 | Page
Page 7
Arecont Vision D4S/D4F Installation Manual
6 | Page
Loading...