Arctic P140 PWM PST User Manual

BioniX P140

Pressure-optimised 140 mm Gaming Fan
with PWM PST

• Optimised for static pressure

• Ideal choice on heatsinks, radiators and (partly-) covered case vents

• Broad RPM range for highest performance and low noise level

• Push- or pull-configuration

• PWM Sharing Technology (PST) regulates fan speed synchronously

• Newly developed, very quiet motor

• Extended life span

• Available in multiple distinct colors

Designed by ARCTIC

PWM Sharing Technology

www.arctic.ac

BioniX P140

Pressure-optimised Gaming Fan with PWM PST140 mm

The BioniX P140 fan features completely redesigned fan
blades and is optimised for high static pressure. Thus, the
BioniX P140 is especially effective when used on heatsinks
and with higher air resistance.
The wide RPM range from 200 to 1 950 RPM can be regulated
seamlessly and synchronously with other fans thanks to
ARCTIC's PWM Sharing Technology (PST).
The newly developed motor with a low coil temperature
significantly increases the life span of the fan. Therefore we
have extended the warranty to 10 years.

Specifications

Fan
Airflow

Bearing
Noise Level
Current / Voltage
Connector

Weight

140 mm, 200 – 1950 RPM (Controlled by PWM)

77.6 CFM/ 131.92 m /h (@ ³1950 RPM)

2.85 mm H2O (@ 1950 RPM)Static Pressure
Fluid Dynamic Bearing

0.45 Sone (@ 1950 RPM)

0.15 A / 12 V DC
4-pin Connector + 4-pin Socket
140 (L) x 140 (W) x 28 (H) mmDimensions
181 g

Maximum Quietness, Minimum Vibration

Even at low speeds the operating sound of the new ARCTIC motor is barely
noticeable.
Due to a sinus-magnetizing the new motor only creates about 5 % of the
commutator oscillations of a regular DC-motor.
Consequently, there is no need for rubber spacers due to the steady and smooth
torque of the new motor.

Fan with newly developed
ARCTIC motor

Fan with regular motor and
anti-vibration rubbers

Fan with regular motor
without vibration absorption

5 % vibration from
commutation

5 % vibration from
commutation

Noise Level

5 % vibration from
commutation

Designed by ARCTIC

BioniX P140

Pressure-optimised Gaming Fan with PWM PST140 mm

Optimised for Static Pressure

During the development of the new BioniX P140, special
emphasis was placed on a focused airstream and thus a high
static pressure. The fan guarantees extremely efficient
cooling, even with increased air resistance.
Therefore, the BioniX P140 is particularly suitable for use on
heatsinks and radiators.

Extended Life Span

A 10 °C lower motor temperature roughly
doubles the life span of a fan. The new ARCTIC
motor has a four times longer service life
through its low coil temperature.
Consequently, we have extended the warranty
to 10 years.

BioniX P140
(New ARCTIC Motor)

No-Name 140 mm Fan
(Typical DC-Motor)

34 4 °C.

Coil Temperature @ 22 °C

Ambient Temperature

54 5 °C.

200 to 1950 RPM regulated via PWM PST

With a wide range of regulation and the PWM Sharing
Technology (PST), the BioniX P140 fan speed can be
controlled synchronously with all your other fans together.
This keeps noise at a minimum while guaranteeing maximum
cooling performance when needed.

More Efficient Technology

The motor is powered by a Neodym-Iron-Boron-Magnet
ring of the newest generation, which allows the new BioniX
P140 to run much more efficiently than its predecessors.
This saves energy and lowers the coil temperature without
comprimising the performance.

BioniX P140

BioniX F140

Power Consumption

0.15 A @ RPM1950

0.25 A @ 1800 RPM

High Quality Bearing

Thanks to an alloy/lubricant combination developed in
Germany, friction within the bearing is reduced and greater
efficiency is achieved. As a result, there is less heat
development as well as less bearing noise, which means you
can enjoy a longer service life from your fan.

Impeller

Teflon Plate

Steel Shaft

Precision Bearing

Lubricant Capsule
Lubricant

Designed by ARCTIC

191023_r6_EN