Arconic 9304-36, 8304, 7304, 6304, 5304 User Manual

November 9, 2016

HK457

Hydraulic Installation Tools

serial numbers 0401 and above

Instruction Manual

5304

6304

6304BOM

7304

8304

9304

9304-36

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

2

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

3

C

C

ONTENTS

ONTENTS

EC Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . 2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Principle of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Preparation for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Components Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . .10-16

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Kits and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

4

I. GENERAL SAFETY RULES:

1. A half hour long hands-on training session with qualified personnel is recom­mended before using Huck equipment.

2. Huck equipment must be maintained in a safe working condition at all times. Tools
and hoses should be inspected at the beginning of each shift/day for damage or
wear. Any repair should be done by a qualified repairman trained on Huck proce­dures.

3. For multiple hazards, read and understand the safety instructions before installing,
operating, repairing, maintaining, changing accessories on, or working near the
assembly power tool. Failure to do so can result in serious bodily injury.

4. Only qualified and trained operators should install, adjust or use the assembly
power tool.

5. Do not modify this assembly power tool. This can reduce effectiveness of safety
measures and increase operator risk.

6. Do not discard safety instructions; give them to the operator.

7. Do not use assembly power tool if it has been damaged.

8. Tools shall be inspected periodically to verify all ratings and markings required, and
listed in the manual, are legibly marked on the tool. The employer/operator shall
contact the manufacturer to obtain replacement marking labels when necessary.
Refer to assembly drawing and parts list for replacement.

9. Tool is only to be used as stated in this manual. Any other use is prohibited.

10. Read MSDS Specifications before servicing the tool. MSDS specifications are
available from the product manufacturer or your Huck representative.

11.Only genuine Huck parts shall be used for replacements or spares. Use of any
other parts can result in tooling damage or personal injury.

12.Never remove any safety guards or pintail deflectors.

13.Never install a fastener in free air. Personal injury from fastener ejecting may
occur.

14.Where applicable, always clear spent pintail out of nose assembly before installing
the next fastener.

15.Check clearance between trigger and work piece to ensure there is no pinch point
when tool is activated. Remote triggers are available for hydraulic tooling if pinch
point is unavoidable.

16.Do not abuse tool by dropping or using it as a hammer. Never use hydraulic or air
lines as a handle or to bend or pry the tool. Reasonable care of installation tools
by operators is an important factor in maintaining tool efficiency, eliminating down­time, and preventing an accident which may cause severe personal injury.

17.Never place hands between nose assembly and work piece. Keep hands clear
from front of tool.

18.Tools with ejector rods should never be cycled with out nose assembly installed.

19.When two piece lock bolts are being used always make sure the collar orientation
is correct. See fastener data sheet for correct positioning.

II. PROJECTILE HAZARDS:

1. Risk of whipping compressed air hose if tool is pneudraulic or pneumatic.

2. Disconnect the assembly power tool from energy source when changing inserted
tools or accessories.

3. Be aware that failure of the workpiece, accessories, or the inserted tool itself can
generate high velocity projectiles.

4. Always wear impact resistant eye protection during tool operation. The grade of
protection required should be assessed for each use.

5. The risk of others should also be assessed at this time.

6. Ensure that the workpiece is securely fixed.

7. Check that the means of protection from ejection of fastener or pintail is in place
and operative.

8. There is possibility of forcible ejection of pintails or spent mandrels from front of
tool.

III. OPERATING HAZARDS:

1. Use of tool can expose the operator’s hands to hazards including: crushing,
impacts, cuts, abrasions and heat. Wear suitable gloves to protect hands.

2. Operators and maintenance personnel shall be physically able to handle the bulk,
weight and power of the tool.

3. Hold the tool correctly and be ready to counteract normal or sudden movements
with both hands available.

4. Maintain a balanced body position and secure footing.

5. Release trigger or stop start device in case of interruption of energy supply.

6. Use only fluids and lubricants recommended by the manufacturer.

7. Avoid unsuitable postures, as it is likely for these not to allow counteracting of nor­mal or unexpected tool movement.

8. If the assembly power tool is fixed to a suspension device, make sure that fixation
is secure.

9. Beware of the risk of crushing or pinching if nose equipment is not fitted.

IV. REPETITIVE MOTION HAZARDS:

1. When using assembly power tool, the operator can experience discomfort in the
hands, arms, shoulders, neck or other parts of the body.

2. When using tool, the operator should adopt a comfortable posture while maintain­ing a secure footing and avoid awkward or off balanced postures.

3. The operator should change posture during extended tasks to help avoid discom­fort and fatigue.

4. If the operator experiences symptoms such as persistent or recurring discomfort,
pain, throbbing, aching, tingling, numbness, burning sensations or stiffness, these
warnings should not be ignored. The operator should tell the employer and consult
a qualified health professional.

V. ACCESSORIES HAZARDS:

1. Disconnect tool from energy supply before changing inserted tool or accessory.

2. Use only sizes and types of accessories and consumables that are recommend­ed. Do not use other types or sizes of accessories or consumables.

VI. WORKPLACE HAZARDS:

1. Be aware of slippery surfaces caused by use of the tool and of trip hazards caused
by the air line or hydraulic hose.

2. Proceed with caution while in unfamiliar surroundings; there could be hidden haz­ards such as electricity or other utility lines.

3. The assembly power tool is not intended for use in potentially explosive environ­ments.

4. Tool is not insulated against contact with electrical power.

5. Ensure there are no electrical cables, gas pipes, etc., which can cause a hazard if
damaged by use of the tool.

VII. NOISE HAZARDS:

1. Exposure to high noise levels can cause permanent, disabling hearing loss and
other problems such as tinnitus, therefore risk assessment and the implementation
of proper controls is essential.

2. Appropriate controls to reduce the risk may include actions such as damping mate­rials to prevent workpiece from ‘ringing’.

3. Use hearing protection in accordance with employer’s instructions and as required
by occupational health and safety regulations.

4. Operate and maintain tool as recommended in the instruction handbook to prevent
an unnecessary increase in the noise level.

5. Select, maintain and replace the consumable / inserted tool as recommended to
prevent an unnecessary increase in noise.

6. If the power tool has a silencer, always ensure that it is in place and in good work­ing order when the tool is being operated.

VIII. VIBRATION HAZARDS:

1. Exposure to vibration can cause disabling damage to the nerves and blood supply
to the hands and arms.

2. Wear warm clothing when working in cold conditions and keep hands warm and
dry.

3. If numbness, tingling, pain or whitening of the skin in the fingers or hands, stop
using the tool, tell your employer and consult a physician.

4. Support the weight of the tool in a stand, tensioner or balancer in order to have a
lighter grip on the tool.

X. HYDRAULIC TOOL SAFETY INSTRUCTIONS:

1. Do not exceed maximum pressure setting stated on tool.

2. Carry out a daily check for damaged or worn hoses or hydraulic connections and
replace if necessary.

3. Use only clean oil and filling equipment.

4. Power units require a free flow of air for cooling purposes and should therefore be
positioned in a well ventilated area free from hazardous fumes.

5. Ensure that couplings are clan and correctly engaged before operation.

6. Do not inspect or clean the tool while the hydraulic power source is connected.
Accidental engagement of the tool can cause serious injury.

7. Be sure all hose connections are tight.

8. Wipe all couplers clean before connecting. Failure to do so can result in damage
to the quick couplers and cause overheating.

GLOSSARY OF TERMS AND SYMBOLS:

- Product complies with requirements set forth by the rele­vant European directives.

- READ MANUAL prior to using this equipment.

- EYE PROTECTION IS REQUIRED while using this equip-
ment.

- HEARING PROTECTION IS REQUIRED while using this
equipment.

Notes: are reminders of required procedures.

Bold, Italic type and underlining

: emphasizes a specific instruction.

S

S

AFETY

AFETY

I

I

NSTRUCTIONS

NSTRUCTIONS

CAUTIONS: show conditions that will
damage equipment and or structure.

WARNINGS: Must be understood to avoid
severe personal injury.

TOOL

TOOL

Fastener Size

[DESIGNATION] INCH (mm)

Stroke

INCH (mm)

Capacity

lbs (kN)

A

A

INCH (cm)

B

B

INCH (cm)

C

C

INCH (cm)

D

D

INCH (cm)

E

E

INCH (cm)

Weight

lbs (kg)

5304 [‐16] 1/2 (12.7) .94 (2.4)

24650 (109.6)

4.85 (12.1) 4.0 (10.2) 2.00 (5.1) .74 (1.9) .468 (1.2) 14.5 (6.6)

6304

[‐20] 5/8 (15.9)

1.28 (3.2)

33,534 (149.2)

7.22 (18.3)

3.63 (9.2) 2.00 (5.1)

.663 (1.7)

.468 (1.2) 16.0 (7.3)

6304BOM

7.09 (18) .533 (1.3)

7304 [‐24] 3/4 (19.1)

42,497 (189)

7.58 (19.3) 4.07 (10.3) 2.25 (5.7) .908 (2.3) .530 (1.3) 17.0 (7.7)

8304 [‐28] 7/8 (22.2)

1.53 (3.9)

61,043 (271.5)

8.09 (20.5) 4.82 (12.2) 2.75 (6.98) 1.00 (2.5) .593 (1.5) 26.3 (11.9)

9304 [‐32] 1 (25.4)

82,885 (386.7)

8.37 (21.2)

5.47 (13.9)

3.25 (8.2) .998 (2.5)
.656 (1.7) 34.0 (15.4)

9304‐36

[‐36] 1‐1/8 (28.6) 8.58 (21.8) 3.38 (8.6) 1.21 (3.1)

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

5

Huck models 5304, 6304, 7304, 8304, and 9304 Hydraulic Installation Tools are used to install C50L and M50L HUCKBOLT

®

Fasteners. Each tool model has the same eccentric configuration to install fasteners in limited clearance applications. The five
tool models vary in size and pull capacity. Each model has a built‐in nose assembly designed to install a specific size fastener.
These tools are designed to be powered by Huck POWERIG®Hydraulic Units 918, 918‐5, 940, and 956. Powerig Hydraulic Units
are preset at the factory to provide 5400‐5700 psi PULL pressure and 2200‐2400 psi RETURN pressure, and must be reset per
specific tool instructions.

D

D

ESCRIPTION

ESCRIPTION

S

S

PECIFICATIONS

PECIFICATIONS

POWER SOURCE:

Huck POWERIG Hydraulic Unit

HOSE KITS:

Use only genuine HUCK Hose Kits rated
@ 10,000 psi working pressure.

MAX OPERATING TEMP:

125°F (51.7°C)

MAX PULL PRESSURE:

5304 ONLY: 5400 psi (372 bar)
ALL OTHER MODELS: 8400 psi (579 bar)

MAX RETURN PRESSURE:

5304 ONLY: 2700 psi (186 bar)
ALL OTHER MODELS: 3200 psi (220 bar)

SERVICE LIFE:

250,000 cycles

MAX FLOW RATE:

2 gpm (7.5 l/m)

HYDRAULIC FLUID:

ATF meeting DEXRON III, DEXRON IV, MERCON, Allison C‐4 or
equivalent specifications.
Fire resistant hydraulic fluid may also be used, and is required
to comply with OSHA regulation 1926.302 paragraph (d): "the
fluid used in hydraulic power tools shall be fire resistant fluid
approved under schedule 30 of the US Bureau of Mines,
Department of Interior, and shall retain its operating charac‐
teristics at the most extreme temperatures to which it will be
exposed."

AB

D

C

E

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

6

When tool hoses and control cord are connected to
the POWERIG, PULL and RETURN strokes of the
tool are controlled by a switch.

When the switch is depressed, a solenoid operated
valve in the POWERIG directs pressurized hydraulic
fluid through the PULL hose to the front side of the
piston and allows fluid on the RETURN side to flow
back to the tank.

The piston/collet moves rearward causing follower
O-Rings and spring to impart a forward motion to the
follower. If the tool is in position on a fastener pin and
collar, this forward motion causes the jaws to clamp
onto the pintail of the fastener. The installation cycle
has begun.

Clamping pressure is applied to the sheets.

The anvil is forced forward, swaging the collar into

locking grooves of the fastener.

When the anvil hits the sheet, continued pull caus-

es the pintail to break off.

When the piston reaches the end of the pull stroke,
it uncovers flats on the rear end of the unloading
valve. These flats were designed to provide a pas­sage for hydraulic fluid from the PULL side to the
RETURN side of the piston “unloading” or “dumping”
the pressurized fluid back to the tank.

When installation is completed, trigger is released.
Hydraulic pressure is directed to RETURN side of pis­ton. It moves forward, and the nose assembly, with
tool, is pushed off the installed fastener.

Huck recommends that only Huck Powerig Hydraulic Units be used as a power source for
Huck installation equipment. Hydraulic power units that deliver high pressure for both PULL
and RETURN, AND ARE NOT EQUIPPED WITH RELIEF VALVES ARE SPECIFICALLY NOT
RECOMMENDED AND MAY BE DANGEROUS.

P

P

RINCIPLE

RINCIPLE

OF

OF

O

O

PERATION

PERATION

9304 Tool

Optional Hose Kit

CAUTION

CAUTION

OL 1

24 VAC

TOOL 2

15 VAC

918 Powerig

CAUTIO

CAUTIO

N

TOOL 1

CAUTIO

N

CAUTIO

N

POWERIG HYDRAULIC UNIT

TOOL 2

N

CAUTIO

N

CAUTIO

N

To primary
power source

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

7

Note: Where a part number (P/N) is given, Huck
sells that part.

Rub Parker Threadmate

®

* thread compound, or equiv-

alent, on pipe plug threads and quick connect fitting.

1. Use Huck POWERIG Hydraulic Unit, or equiva­lent, that has been prepared for operation per
instruction manual. Check both PULL and
RETURN pressures and, if required, adjust to
pressures given in S

PECIFICATIONS section of this

manual.

2. First, turn hydraulic unit to OFF. Then disconnect
power supply from hydraulic unit. Disconnect trig­ger control system from hydraulic unit.

3. Connect PULL pressure hose, with coupler nipple,
into port “P” of tool. Use only with HUCK supplied
hoses rated at 10,000 psi or greater. Check trigger
assembly for apparent damage or wear. If
required, adjust position of trigger assembly on
return pressure hose. Connect trigger control sys­tem to hydraulic unit.

4. Connect hydraulic unit to power supply (air or
electric). Turn hydraulic unit to ON. Depress trig­ger a few times to cycle tool and to circulate
hydraulic fluid. Observe action of Tool and check
for leaks.

5. Disconnect tool from power supply.

WARNING: Correct PULL and RETURN pres­sures are required for operator’s safety and
for Installation TooI’s function. Gage part no.
T-124883CE Is available for checking pres­sures. See Tool S

PECIFICATIONS and Gage

Instruction Manual. Failure to verify pres­sures may result in severe personal injury.

WARNING: Be sure to connect Tool’s
hydraulic hoses to POWERIG Hydraulic Unit
before connecting Tool’s switch control cord
to unit. If not connected in this order, severe
personal Injury may occur.

* Parker Threadmate is a registered trademark of Parker Hannifin Corp..
* TEFLON is a registered trademark of DuPont Corp.

WARNINGS:
Read full manual before using tool.

A half-hour training session with qualified
personnel is recommended before using
Huck equipment.

When operating Huck installation equip­ment, always wear approved eye protection.

Be sure there is adequate clearance for the
operator’s hands before proceeding.

P

P

REPARATION

REPARATION

FOR

FOR

U

U

SE

SE

CAUTION: Do not use TEFLON®* tape on pipe
threads. Pipe threads may cause tape to
shred resulting in tool malfunction. (Parker
Threadmate is available as Huck P/N 508517.)

CAUTION: Do not let disconnected hoses
and couplers contact a dirty floor. Keep
harmful material out of hydraulic fluid. Dirt
in hydraulic fluid causes valve failure In
Tool and In POWERIG Hydraulic Unit.

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

8

General

Operators should receive training from qualified
personnel.

Do not bend tool to free if stuck.

Tool should only be used to install fasteners.
NEVER use as a jack/spreader or hammer.

HUCKBOLT® Fastener Installation:

1. Check work and remove excessive gap. (Gap is
space between sheets. Gap is excessive if not
enough pintail sticks through collar for the tool
jaws to grab onto.)

2. Place pin in workpiece and place collar over pin.
See WARNING. (If Collar has only one tapered
end, that end MUST

be out toward tool; not next

to sheet.)

3. Hold pin and push nose assembly onto pin pro­truding through collar until nose anvil touches
collar. Tool must be held at right angles to work.

4. Move hands away from pin and structure. Keep
hands away from front of tool during operation.
Tool anvil advances forward.

5. Holding tool at right angle (90 degrees) to work,
depress trigger and hold until collar is swaged
and pintail breaks.

6. Release trigger. Tool will go into its return stroke.
Tool/nose are ready for next installation cycle. If
pintail does not break off, operate switch to re­cycle tool until pintail breaks and nose assembly
is ejected from installed fastener.

7. After fastener installation, point nose of tool down
to allow broken-off pintail to drop out.

8. Tool is ready for next installation cycle.

WARNING: To avoid severe personal
injury: Wear approved eye and ear pro-
tection. Be sure of adequate clearance
for Operator’s hands before proceeding
with fastener installation.

O

O

PERATING

PERATING

I

I

NSTRUCTIONS

NSTRUCTIONS

For safe operation. Please read completely

CAUTION: Remove excess gap from
between the sheets. This permits enough
pintail to emerge from collar for ALL jaw
teeth to engage with pintail. If ALL teeth do
not engage properly, jaws will be damaged.

WARNING: Do not pull on a pin without
placing fastener/collar in a workpiece, and
also, collar chamfer MUST be out toward
tool. These conditions cause pin to eject
with great velocity and force when the pin­tail breaks off or teeth/grooves strip. This
may cause severe personal injury.

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

9

System Inspection

1 A clean, well-lit area should be available for servicing

the tool.

2 Inspect tool daily. Check hoses, fittings and discon-

nects for leaks or damage.

3 Special care must be given to prevent contamination

of pneumatic and hydraulic systems.

4 Proper hand tools and soft materials to protect tools

must be available. Use only standard hand tools,
brass drift and wood block. Vise with soft jaws
should be available. Unsuitable hand tools will cause
installation tool damage.

5 Apply continuous strong pressure to disassemble a

component. An arbor press provides steady pres­sure to press a component into or out of an assem­bly.

6 Never continue to force a component if it “hangs-up”

due to misalignment. Reverse the procedure to cor­rect misalignment and start over.

7 Assemble Release and Ejector Kit with Loctite*

adhesive sealant. (part no. 503657).

8 All parts must be handled carefully and examined for

damage and/or wear.

9 Components should be disassembled and assem-

bled in a straight line without bending, cocking or
undue force.

10 Disassembly and assembly procedures outlined in

this manual should be followed. If Huck recommend­ed procedures are not followed, the tool may be
damaged.

11 See SS

PECIFICATIONS

PECIFICATIONS for fluid type. Dispose of fluid in

accordance with local environmental regulations.

12 Recycle steel, aluminum, and plastic parts in accor-

dance with local lawful and safe practices.

Standard Sealants, Lubricants

Rub Slic-Tite®* with PTFE thread compound, or equiva­lent, on pipe plug threads and quick connect fitting.

Smear LUBRIPLATE®13OAA* (Huck P/N 502723), or
equivalent lubricant, on O-Rings and mating surfaces to
aid assembly and to prevent damage to O-Rings.

* Loctite is a registered trademark of Henkel Corporation, U.S.A.
* Slic-Tite is a registered trademark of LA-CO Industries, Inc.
* TEFLON is a registered trademark of DuPont Corp.
* LUBRIPLATE is a registered trademark of Fiske Brothers Refining

Co.

Preventive Maintenance

Operating efficiency of the Tool is directly related to
performance of complete system, including tool/nose
assembly, hydraulic hoses, control trigger assembly
and the POWERIG® Hydraulic Unit. Therefore, an
effective preventive maintenance program includes
scheduled inspections of the system to detect and
correct minor troubles.

● Inspect tool daily for damage or wear.

● Verify that hoses, fittings, and trigger connections
are secure.

● Inspect hydraulic hoses for signs of leaks or
damage. Replace if required.

● Inspect tool, hoses, and POWERIG Hydraulic Unit
during operation to detect abnormal heating, leaks,
or vibration.

● Tool should be checked for leaks before each use.

POWERIG Hydraulic Unit Maintenance

Maintenance and repair instructions are in applicable
POWERIG Hydraulic Unit Instruction Manual.

Tool/Nose Maintenance and Precautions

Whenever disassembled, and also at regular intervals
(depending on severity and length of use), replace all
O-rings and back-up rings. Spare Parts Kits should be
kept on hand. Inspect cylinder bore, piston and
rod/extension, and unloading valve for scored sur­faces, excessive wear or damage. Replace parts as
necessary. Clean all parts in mineral spirits or iso­propyl alcohol only. Do not let jaws come in contact
with other solvents under any circumstances. Also,
do not let jaws soak. Dry the jaws immediately after
cleaning. Dry other parts before assembling. Use a
sharp pointed “pick” to remove imbedded particles
from the pull grooves of the jaws.

M

M

AINTENANCE

AINTENANCE

CAUTIONS:

Consult MSDS before servicing tool.

Keep dirt and other material out of
hydraulic system.

Separated parts most be kept away from
dirty work surfaces.

Dirt/debris in hydraulic fluid causes Dump
Valve failure in Tool and in POWERIG®
Hydraulic Unit’s valves.

Always check tool assembly drawing for
the proper direction of the flats on the
Dump Valve.

Always replace seals, wipers, and back-up
rings when tool is disassembled for any
reason.

CAUTION: Do not use TEFLON®* tape on
pipe threads. Pipe threads may cause tape
to shred resulting in tool malfunction. (Slic­Tite is available in stick form as Huck P/N

503237.)

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

10

5304 C

5304 C

OMPONENTS

OMPONENTS

D

D

RAWING

RAWING

110439 Female Connector

110438 Male Connector

503431 Reducing Bushing

Piston Collet

502804 Back-up Ring

2

504671 O-Ring

2

590189-3 Sticker

Notes:

Release and Ejector are not sold separately.

They must be purchased as Release and Ejector Kit 120836.

1

3

3

501162 Back-up Ring

504641 O-Ring

122315-1 Follower

500845 O-Ring (11)

504630 O-Ring

590160 Sticker

501151 Back-up Ring

Piston Collet is not sold separately. If it must be replaced,

it must be purchased as Piston Collet Assembly 110785,

which also contains O-Ring and Back-Up Ring.

2

3

109541 Locking Ring

Cylinder Head

127549 Cylinder

Cylinder Head is not sold separately. If it must be replaced,

3

122318 Retainer

it must be purchased as Cylinder Head Assembly 110786,

which also contains internal O-Rings and Back-Up Rings.

109545

Tool Capacity: 24,650 lbs @5,400 psi

3

3

504627 O-Ring

501148 Back-up Ring

500790 O-Ring

Ejector

1

Anvil

501214 Screw

502847 Lockwasher

110447

104719

Release

1

Chuck Jaws

Relief Valve

505134

Reducing Bushing

118940-3 Trigger & Cord Assembly

Hose

118944-2

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

11

6304 C

6304 C

OMPONENTS

OMPONENTS

D

D

RAWING

RAWING

3

Notes:

Release and Ejector are not

sold separately. They must

be purchased as Release and

1

Ejector Kit 123317.

Piston is not sold separately.

2

123749-3

If it must be replaced, it must

be purchased as Piston Assy

110610, which contains Piston,

Release, Ejector, O-Ring, and

Hose

Back-Up Ring.

Cylinder Head is not sold

3

separately. If it must be

replaced, it must be

purchased as Cylinder Head

Assembly 110901, which also

contains internal O-Rings and

Back-Up Rings.

Tool Capacity:

33,534 lbs @8,400 psi

2

500845 O-Ring (16)

Piston

503021 Back-up Ring

2

3

3

501148 Back-up Ring

504627 O-Ring

504670 O-Ring

2

504630 O-Ring

590501-8400 & 590515 Stickers

122318 Retainer

104891 Locking Ring

500790 O-Ring

122315 Follower

501151 Back-up Ring

106612 Cylinder

Cylinder Head

Anvil

110605

110164 Key

110811 Shield

Release

1

Ejector

2

1
2

501224 Screw

501084

104706 Chuck Jaws

109011 Retainer

O-Ring

504551

Back-up Ring

501267 Screw

106608 Pressure Tube

504637 O-Ring

501158 Back-up Ring

3

3

Clamp Assembly

123380 Trigger/Hose

123381 Trigger & Cord Assembly

110438 Male Connector

110439 Female Connector

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

12

6304BOM C

6304BOM C

OMPONENTS

OMPONENTS

D

D

RAWING

RAWING

3

Notes:

Release and Ejector are not

sold separately. They must

be purchased as Release and

Ejector Kit 124827.

1

Piston is not sold separately.

2

Hose

123749-4

If it must be replaced, it must

be purchased as Piston Assy

110609-1, which contains Piston,

Release, Ejector, O-Ring, and

Back-Up Ring.

Cylinder Head is not sold

3

separately. If it must be

replaced, it must be

purchased as Cylinder Head

Assembly 110901, which also

contains internal O-Rings and

Back-Up Rings.

Tool Capacity:

33,534 lbs @8,400 psi

2

500845 O-Ring (16)

Piston

503021 Back-up Ring

2

3

3

501148 Back-up Ring

504627 O-Ring

504670 O-Ring

2

504630 O-Ring

590501-8400 & 590515 Stickers

122318 Retainer

104891 Locking Ring

500790 O-Ring

122315 Follower

501151 Back-up Ring

106612 Cylinder

Cylinder Head

124825

110164 Key

Ejector

1

Anvil

2

501224 Screw

110811 Shield

501084

Back-up Ring

501267 Screw

Release

1
2

119583 Chuck Jaws

109011 Retainer

O-Ring

504551

106608 Pressure Tube

504637 O-Ring

501158 Back-up Ring

3

3

Clamp Assembly

123380 Trigger/Hose

123381 Trigger & Cord Assembly

110438 Male Connector

110439 Female Connector

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

13

7304 C

7304 C

OMPONENTS

OMPONENTS

D

D

RAWING

RAWING

3

Notes:

Release and Ejector are not

sold separately. They must

be purchased as Release and

1

Ejector Kit 122297.

Piston is not sold separately.

If it must be replaced, it must

be purchased as Piston Assy

2

Hose

123749-4

110612, which contains Piston,

Release, Ejector, O-Ring, and

Back-Up Ring.

Cylinder Head is not sold

separately. If it must be

replaced, it must be

purchased as Cylinder Head

3

Assembly 110902, which also

contains internal O-Rings and

Back-Up Rings.

Tool Capacity:

42,497 lbs @8,400 psi

2

500847 O-Ring (16)

Piston

503411 Back-up Ring

2

3

3

501150 Back-up Ring

504629 O-Ring

504673 O-Ring

2

504632 O-Ring

590501-8400 & 590515 Stickers

122298 Retainer

106533 Locking Ring

500792 O-Ring

122295 Follower

501153 Back-up Ring

106526 Cylinder

110164 Key

Cylinder Head

Ejector

1

Anvil

2

110597

501224 Screw

110812 Shield

501084

Back-up Ring

501267 Screw

Release

1
2

104926 Chuck Jaws

109011 Retainer

O-Ring

504551

504640 O-Ring

3

590059 Sticker

106532 Pressure Tube

501161 Back-up Ring

3

Clamp Assembly

123380 Trigger/Hose

123381 Trigger & Cord Assembly

110438 Male Connector

110439 Female Connector

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

14

8304 C

8304 C

OMPONENTS

OMPONENTS

D

D

RAWING

RAWING

3

Notes:

Release and Ejector are not

sold separately. They must

be purchased as Release and

1

Ejector Kit 121242.

Piston is not sold separately.

If it must be replaced, it must

be purchased as Piston Assy

2

Hose

123749-4

110614, which contains Piston,

Release, Ejector, O-Ring, and

Back-Up Ring.

Cylinder Head is not sold

separately. If it must be

replaced, it must be

purchased as Cylinder Head

3

Assembly 110903, which also

contains internal O-Rings and

Back-Up Rings.

Tool Capacity:

61,043 lbs @8,400 psi

3

504645 O-Ring

2

500852 O-Ring (21)

Piston

503585 Back-up Ring

2

504678 O-Ring

2

3

500796 O-Ring

501166 Back-up Ring

504669 O-Ring

122292 Follower

502841 Back-up Ring

590501-8400 & 590515 Stickers

122293 Retainer

106433 Locking Ring

106427 Cylinder

Cylinder Head

Anvil

110595

110164 Key

110813 Shield

Release

1

Ejector

2

1
2

501224 Screw

501084

104927 Chuck Jaws

109011 Retainer

504551

Back-up Ring

501267 Screw

106434 Pressure Tube

O-Ring

504632 O-Ring

501153 Back-up Ring

3

3

590059 Sticker

Clamp Assembly

123380 Trigger/Hose

123381 Trigger & Cord Assembly

110438 Male Connector

110439 Female Connector

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

15

9304 C

9304 C

OMPONENTS

OMPONENTS

D

D

RAWING

RAWING

3

Notes:

Release and Ejector are not

sold separately. They must

be purchased as Release and

1

Ejector Kit 122322.

Piston is not sold separately.

If it must be replaced, it must

be purchased as Piston Assy

2

Hose

123749-4

110616, which contains Piston,

Release, Ejector, O-Ring, and

Back-Up Ring.

Cylinder Head is not sold

separately. If it must be

replaced, it must be

purchased as Cylinder Head

3

Assembly 110904, which also

contains internal O-Rings and

Back-Up Rings.

Tool Capacity:

82,885 lbs @8,400 psi

3

504634 O-Ring

2

500878 O-Ring (14)

Piston

503412 Back-up Ring

2

504683 O-Ring

2

590501-8400 & 590515 Stickers

3

500798 O-Ring

501155 Back-up Ring

504672 O-Ring

502938 Back-up Ring

122323 Retainer

114214 Locking Ring

122320 Follower

106427 Cylinder

Cylinder Head

Anvil

110593

110164 Key

110814 Shield

Release

1

Ejector

2

1
2

501224 Screw

501084

104928 Chuck Jaws

109011 Retainer

504551

Back-up Ring

501267 Screw

106134 Pressure Tube

O-Ring

504650 O-Ring

502432 Back-up Ring

3

3

590059 Sticker

Clamp Assembly

123380 Trigger/Hose

123381 Trigger & Cord Assembly

110438 Male Connector

110439 Female Connector

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

16

9304-36 C

9304-36 C

OMPONENTS

OMPONENTS

D

D

RAWING

RAWING

3

Notes:

Release and Ejector are not

sold separately. They must

be purchased as Release and

Ejector Kit 122684.

1

Piston is not sold separately.

2

123749-4

If it must be replaced, it must

Hose

be purchased as Piston Assy

122698, which contains Piston,

Release, Ejector, O-Ring, and

Back-Up Ring.

3

Cylinder Head is not sold

separately. If it must be

replaced, it must be

purchased as Cylinder Head

Assembly 110904, which also

contains internal O-Rings and

Back-Up Rings.

Tool Capacity:

82,885 lbs @8,400 psi

3

504634 O-Ring

2

500878 O-Ring (14)

Piston

503412 Back-up Ring

2

504683 O-Ring

2

590189-1 Caution Sticker

3

500798 O-Ring

501155 Back-up Ring

504672 O-Ring

502938 Back-up Ring

122323 Retainer

114214 Locking Ring

122320 Follower

106140 Cylinder

110164 Key

Cylinder Head

Ejector

Anvil

1
2

122697

501224 Screw

110814 Shield

501084

Back-up Ring

501267 Screw

Release

1
2

104928 Chuck Jaws

109011 Retainer

O-Ring

504551

504650 O-Ring

3

590059 Sticker

106134 Pressure Tube

502432 Back-up Ring

3

Clamp Assembly

123380 Trigger/Hose

123381 Trigger & Cord Assembly

110438 Male Connector

110439 Female Connector

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

17

The following procedure is for disassembly of Tool.
Remove only those parts necessary. Check and
replace damaged/worn components. Always replace

O-rings, wipers, and back-up rings of disassem­bled subassemblies.

NOTES:

(a) Always work on a clean surface.
(b) Use relatively soft materials, such as brass,

aluminum, or wood to protect tool when apply­ing pressure.

(c) Apply a continuous, strong pressure rather

than sharp blows to disassemble or assemble
a component. An arbor press provides steady
pressure to press a component in or out.

(d) Never continue to force a component if it

“hangs-up” due to misalignment. Instead,
reverse the procedure to correct misalignment
and start over.

(e) Assemble release and ejector with Loctite

adhesive/sealant, HUCK part no. 503657.
Loctite is included in release and ejector kits.

(f) Lubricate O-Rings and coat hose fitting

threads per instructions in MM

AINTENANCE

AINTENANCE sec-

tion of this manual.

(g) Standard hand tools such as wrenches, drifts,

hex keys, etc., are required. Some standard
tools are available from HUCK. Please contact
your HUCK representative.

For component identificcation, please refer to individ­ual CC

OMPONENTS

OMPONENTS

D

D

RAWINGS

RAWINGS in this manual.

1. Disconnect Tool’s electric trigger control cord,
then uncouple Hydraulic Hoses.

2. Remove Socket Head Cap Screw that attaches
Anvil Retainer to Cylinder. Unscrew Anvil.

3. Unscrew Coupler Nipple and Coupler Body, and
drain hoses into a clean container.

4. Push rearward on Piston Assembly until hydraulic
fluid is drained into container.

5. Remove Screws, Washers, and Nuts from Clamp.
Separate Clamp from Switch and Control Cord
Assembly and Hydraulic Hoses.

6. Remove both hoses from head assembly.

7. Remove Socket Head Cap Screws and Shield.
Turn tool until Key falls out of locking slots.
Remove Locking Ring with a spanner wrench.

8. Push rearward on Piston Assembly until head
assembly and piston assembly slides out of
Cylinder.

9. Remove Pressure ube Assembly from Piston or
Head.

10.Remove Retainer and O-Ring Assembly from pis­ton with a spanner wrench.

11. Slide Follower Assembly, O-Rings, and Jaws from
piston/collet.

12.If necessary, disassemble Release and Ejector by
unscrewing by hand or with pliers.

13.If necessary, loosen two Screws on Cord Grip.
Loosen Cup Point Setscrew. Pull Switch from
Housing, and remove Strain Relief. Disassemble
Electrical Connector to replace Connector or to
re-wire.

D

D

ISASSEMBLY

ISASSEMBLY

WARNING: Be sure to disconnect Tool’s
control trigger system from POWERIG®
Hydraulic Unit before disconnecting Tool’s
hydraulic hoses from unit. If not discon­nected in this order before any mainte­nance or cleaning is done, severe person­al injury may occur.

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

18

Clean all tool components with mineral spirits, or
equivalent, and inspect for wear or damage. Replace
as required. Always replace all seals on/in disas-
sembled components. Use O-rings and back-up
rings supplied in SERVICE PARTS KIT. Smear
LUBRIPLATE 130AA, or equivalent, on O-rings,
back-up rings and mating components for ease of
assembly. Assemble Tool taking care not to damage
either O-rings or back-up rings.

1. Apply Vibratite to Jaw Release and assemble to
Piston and collar Ejector.

2. Hold piston with large opening facing up, and
place three jaw segments into piston, one at a
time, so that the taper of jaws match the cone
angle of the piston.

3. Push O-Rings onto Follower. Drop assembled
components into piston against jaws.

4. Push Retainer Assembly over Follower, and
screw it into Piston. Tighten Retainer with a span­ner wrench until Retainer shoulder is tight against
piston extension.

5. Align eccentric front extension of Piston with
eccentric hole in front of Cylinder, and push
Piston into Cylinder.

6. Slide Pressure Tube Assembly through hole in
Piston.

7. Place Locking Ring over rear of Head Assembly.
Hold head and ring together. The tube pocket in
the head must be aligned with the tube in the pis­ton while pushing the head int the Cylinder.
When Locking Ring stops head, alternately push
in head and turn in locking ring.

8. Tighten Locking Ring, then back it out 1/8 turn or
less until slot in head and slot in ring are aligned.
Hold tool pointing down, and place Key into slots.
Place Shield on head and tighten both Socket
Head Cap Screws.

9. Screw Anvil into Cylinder.

10. Assemble Anvil Retainer and screw into Cylinder.

11. Screw Coupler Nipple and Coupler Body (male
and female connectors) onto hydraulic hoses.
Screw hose with nipple into port “P” of head.
Screw other hose into head.

12. Assemble Electrical Control Cord to disassem­bled plug of electrical connector assembly.
Assemble electrical connector plug.

13. Replace and tighten Cord Grip in Housing.

14. Assemble Switch. Push cord thru cord grip and
housing. Attach cord to switch with two screws.

15. Slide switch with cord attached into housing.
Tighten screw against switch. Tighten two screws
in cord grip to hold in housing.

16. Place two halves of clamp over “R” hose. Align
clamp holes and loosly attach screw, washer, and
nut. Push assembled switch and housing into
clamp, hold it centered, and tighten screws.

17. Connect hoses and cord to POWERIG hoses
and control cord. Cycle tool a few times. Observe
action of tool, and check for leaks.

A

A

SSEMBLY

SSEMBLY

WARNING: Do not omit any seals during
servicing, leaks will result and personal
injury may occur.

CAUTION: Do not use TEFLON

®

* tape on
pipe threads. Pipe threads may cause tape
to shred resulting in tool malfunction.
(Slic-Tite is available in stick form as Huck
P/N 503237.)

WARNING: Tool must be fully assembled
with all components included.

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

19

Service Parts Kits
5304KIT, 6304KIT, 7304KIT, 8304KIT, & 9304KIT

Include all perishable seals, O-rings and Back-up
rings. A spare Service Parts Kit should be kept on
hand at all times.

Release and Ejector Kit
120836 (5304)
122317 (6304)
124827 (6304BOM)
122297 (7304)
121242 (8304)
122322 (9304)
122684 (9304-36)

Release and Ejector Tool (see below)
124751 (5304, 6304, 7304, 8304)
124751-1 (9304 series)

This assembly tool is for disassembling and assem­bling -20 (5/8) and -24 (3/4) release and ejector
assemblies in for 99-5000 series nose assemblies.
The locking taper locks into the taper of the release,
preventing the release fom turning while the ejector is
unscrewed, using an open end wrench.

T

O USE:

1. Lock assembly tool in vise
as shown.

2. Place collet assembly
over taper Using a soft
mallet (or hammer), tap
assembly firmly onto taper
to ensure that tapers are
locked together.

3. Using an open end
wrench on ejector flats,
unscrew ejector from
release.

4. Lift collet off release. With
soft mallet tap release
from assembly tool.

5. Assemble in reverse
order.

Handle Carrier Assembly (see below)
112584-4 (6304 series)
112584-3 (7304)
112584-5 (8304)
112584-2 (9304 series)

K

K

ITS

ITS

AND

AND

A

A

CCESSORIES

CCESSORIES

Release and Ejector Tool

Optional Handle Carrier Assembly

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

20

1. Tool fails to operate when trigger is depressed.

a. Inoperative POWERIG® Hydraulic Unit. See

applicable instruction manual.
b. Loose air or electric connections.
c. Damaged trigger assembly.
d. Loose or faulty hydraulic hose couplings.
e. Pressure Tube not installed in Tool.

2. Tool leaks hydraulic fluid.

a. Defective Tool O-rings or loose hose connections

at Tool.

3. Hydraulic couplers leak fluid.

a. Damaged or worn O-rings in coupler body. See

Coupler 110440.

4. Hydraulic fluid overheats.

a. Hydraulic unit not operating properIy.
b. Pressure Tube installed incorrectly.
c. POWERIG Hydraulic Unitnot operating properly;

see unit’s manual.
d. Restriction in hydraulic line.

5. Tool operates erratically and fails to install fasten­er properly.

a. Low or erratic hydraulic pressure; air in system
b. Damaged or worn piston/anvil O-ring in Tool.
c. Pressure Tube installed incorrectly.
d. Excessive wear on sliding surfaces of Tool parts.
e. Excessive wear of unloading valve in Tool.

6. Collar of HUCKBOLT® fastener not completely

swaged.

a. Improper Tool operation. See Trouble 6.
b. Scored anvil.

7. Tool “hangs-up” on swaged collar of HUCKBOLT
Fastener.

a. Improper Tool operation. See Trouble 6.
b. RETURN pressure too low.

8. Pintail of fastener fails to break.

a. Improper Tool operation. See Trouble 6.
b. Pull grooves on fastener stripped. See Trouble 7.
c. PULL pressure too low.
d. Worn Pressure Tube.

9. Jaw segments do not maintain proper position in
piston.

a. Incorrect amount of follower O-rings. Clean before

reassembling.

10. Pull grooves on fastener pintail stripped during
PULL stroke.

a. Broken pintail not removed from tool.
b. Anvil was not slid completely onto fastener pintail.
c. Incorrect fastener length.
d. Worn or damaged jaw segments.
e. Metal particles accumulated in pull grooves of

jaw segments.
f. Jaw release binding.
g. Excessive sheet gap.

11. Tool operates in reverse.

a. Reversed hydraulic hose connections between

POWERIG and tool.

12. Anvil will not slide completely over fastener pin­tail.

a. Broken pintail not removed from tool.
b. Incorrect fastener length.

T

T

ROUBLESHOOTING

ROUBLESHOOTING

Always check the simplest possible cause of a malfunction first. For example, a loose or disconnected trig­ger line. Then proceed logically, eliminating each possible cause until the defective part is located. Where
possible, substitute known good parts for suspected defective parts. Use Trouble Shooting Chart as an aid
for locating and correcting trouble.

5304 6304 7304 8304 9304 Hydraulic Tooling (HK457)

21

Limited Warranties

Tooling Warranty:

Huck warrants that tooling and other items (excluding fas­teners, and hereinafter referred as "other items") manufac­tured by Huck shall be free from defects in workmanship
and materials for a period of ninety (90) days from the
date of original purchase.

Warranty on "non standard or custom manufactured prod­ucts":

With regard to non-standard products or custom manufac­tured products to customer's specifications, Huck warrants
for a period of ninety (90) days from the date of purchase
that such products shall meet Buyer's specifications, be
free of defects in workmanship and materials. Such war­ranty shall not be effective with respect to non-standard or
custom products manufactured using buyer-supplied
molds, material, tooling and fixtures that are not in good
condition or repair and suitable for their intended pur­pose.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND
THE DESCRIPTION ON THE FACE HEREOF. HUCK MAKES
NO OTHER WARRANTIES AND EXPRESSLY DISCLAIMS
ANY OTHER WARRANTIES, INCLUDING IMPLIED WAR­RANTIES AS TO MERCHANTABILITY OR AS TO THE FIT­NESS OF THE TOOLING, OTHER ITEMS, NONSTANDARD
OR CUSTOM MANUFACTURED PRODUCTS FOR ANY PAR­TICULAR PURPOSE AND HUCK SHALL NOT BE LIABLE
FOR ANY LOSS OR DAMAGE, DIRECTLY OR INDIRECTLY,
ARISING FROM THE USE OF SUCH TOOLING, OTHER
ITEMS, NONSTANDARD OR CUSTOM MANUFACTURED
PRODUCTS OR BREACH OF WARRANTY OR FOR ANY
CLAIM FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Huck's sole liability and Buyer's exclusive remedy for any
breach of warranty shall be limited, at Huck's option, to
replacement or repair, at FOB Huck's plant, of Huck manu­factured tooling, other items, nonstandard or custom
products found to be defective in specifications, workman­ship and materials not otherwise the direct or indirect
cause of Buyer supplied molds, material, tooling or fix­tures. Buyer shall give Huck written notice of claims for
defects within the ninety (90) day warranty period for
tooling, other items, nonstandard or custom products
described above and Huck shall inspect products for which
such claim is made.

Tooling, Part(s) and Other Items not manufactured by
Huck:

HUCK MAKES NO WARRANTY WITH RESPECT TO THE
TOOLING, PART(S) OR OTHER ITEMS MANUFACTURED
BY THIRD PARTIES. HUCK EXPRESSLY DISCLAIMS ANY
WARRANTY EXPRESSED OR IMPLIED, AS TO THE CONDI­TION, DESIGN, OPERATION, MERCHANTABILITY OR FIT­NESS FOR USE OF ANY TOOL, PART(S), OR OTHER ITEMS
THEREOF NOT MANUFACTURED BY HUCK. HUCK SHALL
NOT BE LIABLE FOR ANY LOSS OR DAMAGE, DIRECTLY
OR INDIRECTLY, ARISING FROM THE USE OF SUCH
TOOLING, PART(S) OR OTHER ITEMS OR BREACH OF
WARRANTY OR FOR ANY CLAIM FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES.

The only warranties made with respect to such tool,
part(s) or other items thereof are those made by the man­ufacturer thereof and Huck agrees to cooperate with
Buyer in enforcing such warranties when such action is
necessary.

Huck shall not be liable for any loss or damage resulting
from delays or nonfulfillment of orders owing to strikes,
fires, accidents, transportation companies or for any rea­son or reasons beyond the control of the Huck or its sup­pliers.

Huck Installation Equipment:

Huck International, Inc. reserves the right to make changes
in specifications and design and to discontinue models
without notice.

Huck Installation Equipment should be serviced by trained
service technicians only.

Always give the Serial Number of the equipment when cor­responding or ordering service parts.

Complete repair facilities are maintained by Huck
International, Inc. Please contact one of the offices listed
below.

Eastern
One Corporate Drive Kingston, New York 12401-0250
Telephone [phone] FAX [phone]

Outside USA and Canada
Contact your nearest Huck International Office, see back
cover.

In addition to the above repair facilities, there are
Authorized Tool Service Centers (ATSC's) located through­out the United States. These service centers offer repair
services, spare parts, Service Parts Kits, Service Tools Kits
and Nose Assemblies. Please contact your Huck
Representative or the nearest Huck office listed on the
back cover for the ATSC in your area.

Arconic Inc. (NYSE: ARNC) creates breakthrough
products that shape industries. Working in close
partnership with our customers, we solve complex
engineering challenges to transform the way we
fly, drive, build and power.

Through the ingenuity of our people and cutting­edge advanced manufacturing, we deliver these
products at a quality and efficiency that ensures
customer success and shareholder value.

AMERICAS

Kingston Operations
1 Corporate Drive
Kingston, NY 12401
800-278-4825
845-331-7300
FAX: [phone]

Carson Operations
900 Watson Center Rd.
Carson, CA 90745
800-421-1459
310-830-8200
FAX: [phone]

Waco Operations
PO Box 8117
8001 Imperial Drive
Waco, TX 76714-8117
800-388-4825
254-776-2000
FAX: [phone]

Tucson Operations
3724 East Columbia
Tucson, AZ 85714
800-234-4825
520-747-9898
FAX: [phone]

Acuña Operations
Hidalgo #120
Parque Industrial Amistad
26220 Acuña Coahuila
Mexico
FAX: [phone]
TELEX: 1173530 LUKSME

EUROPE

Telford Operations
Unit C, Stafford Park 7
Telford, Shropshire
England TF3 3BQ
01952-290011
FAX: [phone]

Us Operations
BP4
Clos D’Asseville
95450 Us par Vigny
France
33-1-30-27-9500
FAX: [phone]

FAR EAST

Melbourne Operations
11508 Centre Road
Clayton, Victoria
Australia 3168
03-764-5500
Toll Free: 008-335-030
FAX: [phone]

Arconic Fastening Systems and Rings world-wide locations:

Huck provides technical assistance
regarding the use and application of
Huck fasteners and tooling.

NOTICE: The information contained in
this publication is only for general guid­ance with regard to properties of the
products shown and/or the means for
selecting such products, and is not

intended to create any warranty,
express, implied, or statutory; all war­ranties are contained only in Huck’s
written quotations, acknowledgments,
and/or purchase orders. It is recom­mended that the user secure specific,
up-to-date data and information regard­ing each application and/or use of such
products.

© 2016 Huck International, Inc.
1 Corporate Drive, Kingston, NY 12401 • Tel: [phone] • Fax: [phone]

Certified to

ISO 9001:2008

Industrial
Products

Certified to

ISO 14001:2004

Industrial

Products