transmit data, including mobile data and WiFi.
- WiFi Touch to open the WiFi settings.
- 3G to turn on/off the 3G connection.
- Auto-rotate screen: Drag the switch to On to lock the screen in landscape
orientation, so it doesn’t rotate when you turn the tablet.
- Brightness: Drag the slider to change the brightness of the screen. Or touch Auto
to have the tablet set screen brightness automatically, using its sensors to measure
the amount of light in your surroundings.
- Notifications: Drag the slider to Off if you don’t want to be disturbed by system
or application notifications about new mail, invitations to chat, and so on.
- Settings: Touch to open the Settings application.
Enabling WiFi
Before launching an Internet application such as the web browser, see if you are connected to an WiFi access point. The icon in the right side of the system
bar is blue when your device is connected to a WiFi network and grey when you are not connected. If not connected, you first need to activate the WiFi and
configure a WiFi network.
From the system bar, you can access the WiFi settings quickly.
1. Touch the time in the system bar.
2. Touch the status icons. The status details is displayed below.
3. Touch WiFi to open the WiFi settings.
4. In the Settings screen, select Wireless & networks.
5. If the WiFi is off, tap on the WiFi line to turn it on. Then select WiFi settings. The ARCHOS will scan
automatically for available WiFi networks and show all the wireless networks in range of your device. The list
is refreshed continuously.
4. Tap on the network you want to connect to. Networks shown with the icon are secured connections.
A password is required for a secured connection. Enter the required network information* and then tap on
Connect. Your ARCHOS will now attempt to establish a connection to that WiFi access point with the
network parameters you entered.
* For free access WiFi points, there is no need to enter any special information. For secured networks, you will
need either a key (a series of numbers and/or letters) of the type WEP, WPA, or WPA2, or you will need to
have a WiFi access point that uses the WiFi protection standard WPS (WiFi Protected Setup). Check with the
Internet service provider to obtain the exact connection parameters required.
ADVANCED CONNECTION
To manually scan for available WiFi networks,
1.Go to the WiFi settings screen. 2.Tap on the Menu button in the upper right corner. 3.Tap on Scan.
If the WiFi network you want to connect to does not appear in the list,
1.Scroll down the screen. 2.Tap on Add WiFi network. 3.Enter the required settings. 4.Tap on Save.
To access the advanced network parameters (Regulatory domain, IP address, etc),
1.Tap on the Menu button in the upper right corner. 2.Tap on Advanced.
Other parameters will appear: the required information can be obtained from the Internet service provider.
WiFi connection problems
The ARCHOS internet tablets support the 802.11 b, g, and n WiFi protocols. If you cannot connect to your access point, first determine if the problem lies with
your access point or with the ARCHOS. Try using another WiFi device, such as a laptop computer or a WiFi enabled telephone and see if that will connect to
your access point. If it does, then use the same WiFi connection settings that it has on your ARCHOS. You could also try connecting your ARCHOS to a
friend's WiFi network and if this works, change your access point parameters to similar ones.
Possible solutions
1. Check your WiFi router/modem documentation to see if it has a pairing button that needs to be pressed. Some modems have such a button that must be
pressed the very first time you try to make a WiFi connection with a new device.
2. If you have to enter a password (a security code of type WEP or WPA) be very careful that you do not confuse a 1 and I (one and letter “I”), a 0 and O (zero
and letter “O”), or U and V. These are common mistakes.
3. When entering a security code for your WiFi access, check the box Show password which will allow you to see exactly what you are typing in. This will
avoid any mistakes.
4. Some access points use what is known as MAC filtering. That means, the WiFi access point has a list of access numbers (every hardware device has a
unique MAC number) which are the only ones allowed to access to the WiFi point. The person managing the WiFi modem/router should shut off this MAC
filtering system to see if this solves the problem. It is recommended to shut off MAC filtering in general as this is now known to be an outdated and ineffective
system for WiFi security. If you must use it, you can find your device's specific MAC address by going to Settings > Wireless & Networks > WiFi settings >
Menu > Advanced. It will look something like 00:16:dc:5e:9e:39.
5. Try temporarily shutting off the encryption system of your WiFi router/modem to see if the problem has to do with the encryption system you are using. The
preferred encryption system is the WPA2.