Arc AAS6SE3, CP6BLS, CF6BLS, CG6BLS, AAG6SE1 User Manual

600mm & 900mm
Canopy Rangehoods

600mm Models: AAS6SE3 pyramid / s/steel
CP6BLS pyramid / s/steel
CF6BLS flat / s/steel
CG6BLS curved glass & s/steel
AAG6SE1 curved glass & s/steel
RFT6 flat / s/steel
RGT6 curved glass & s/steel

900mm Models: AAS9SE3 pyramid / s/steel
CP9BLS pyramid / s/steel
CP9BLB pyramid / black
CF9BLS flat / s/steel
IAF9SE3 flat / s/steel
CG9BLS curved glass & s/steel
AAG9SE3 curved glass & s/steel
RFT9 flat / s/steel
RGT9 curved glass & s/steel

distributors of

INSTALLATION AND OPERATION MANUAL

Dear Customer,
We thank you for choosing this quality appliance and hope you enjoy many years of

reliable service.
Please ensure this manual is read carefully before installation and use. Keep this

manual in a safe and accessible location should future reference be required.
Regards

Home Appliances

CONTENT

2 …………………………………………………. Notice

3 …………………………………………………. Caution

4 …………………………………………………. Feature

5-8 ……………………………………………….. Installation

9 ………………………………………………….. Notice of installation

10 ……………………………………………..….. Safety Warning

11-16 …………………………………………..… Use

17 ………………………………………………… Maintenance

18 ………………………………………………… Light Replacing

19 ………………………………………………… Abnormity and Solution

CanopyInstallationandOperationManual

NOTICE

1. Thank you for choosing our canopy rangehood. Please read the instruction

manual carefully before use.

2. The installation work must be undertaken by a qualified and competent fitter.

3. The manufacturer disclaims all liability for any damage or injury caused as a

result of not following instructions for installation contained in the following
text.

The cooker hood is used on 220/240v, 50Hz.

Home Appliances – October 2013

1

CanopyInstallationandOperationManual

SAFETY WARNINGS

 Installation of this Integrated Canopy Rangehood must be carried by a

qualified and competent installer.

 The manufacturer disclaims and liability for any damage or injury caused as a

result of not following instruction of installation contained in this instruction
manual.

 This Integrated Canopy Rangehood is not intended for use by young children

or infirm persons without supervison.

 Young children should be supervised to ensure they do not play with this

Integrated Canopy Rangehood.

 To avoid possible electric shock this Integrated Canopy Rangehood should be

unplugged before any maintenance or cleaning is carried out.

 This Integrated Canopy Rangehood cannot be installed in an external

environment.

 The Grease Filters should be cleaned at least once a month to avoid the risk

of fire.

 Flambe cooking cannot be carried out under the Integrated Canopy

Rangehood and is not recommended for use over Barbeques.

 Ducting must be independent from any other form of ducting of other

household heating sources.

 Ducting into wall cavities is prohibited unless the cavity has been designed for

this purpose

 Lit gas burner should never remain uncovered or on when there is no pan

present due to the risk of fire.

 Adequate ventilation of the room is required when the cooker hood is used at

the same time as appliances burning gas or other fuels.

- CAUTION: Accessible parts may become hot when used with cooking appliances.

Home Appliances – October 2013

2

CanopyInstallationandOperationManual

(2) FEATURE

1. The cooker hood uses high quality materials, and is made with a streamlined

design.

2. Equipped with a large power low noise electric motor and centrifugal leaf, it

produces strong suction, low noise, non stick grease filter and easy to clean.

3. With the isolated low voltage circuit board control, 12vAC input, the lights are

therefore safer.

4. Special wind tunnel construction and oil collector design, free dirt will be

absorbed in a second.

Home Appliances – October 2013

3

CanopyInstallationandOperationManual

(3). Installation

If the model without Glass:

3.1 The cooker hood shall be placed at a
distance of 65-75cm (26-30inch) from the
cooking surface. See Pic 1.

3.2 Install the hook on a suitable place once the
installation height is fixed, and keep it in line. The
fixed position of the inside chimney bracket is
the place of chimney. See Pic 2.

3.3 Fix one-way valve on the hood and connect
the extensible pipe to the one-way valve. See Pic 3.

3.4 Put the cooker hood on the hook. See Pic 4.

3.5 Use clamp to fix the T-piece valve on the extensible pipe. See Pic 5.

3.6 Fix plate on the outer chimney, and be sure that the inside chimney can be
adjusted the height in it freely, See Pic 6.

3.7 Install the chimney and screw the T-piece metal outlet to the inside chimney, See
Pic 7 and 8.

3.8 Adjust the height of the inside chimney to the position of the inside chimney
bracket and fix on it by screw, after adjusting the position, fix the body with safety
screw. See Pic 9.

Note: The two safety vents are positioned on the back casing, with diameter
of 6mm.

Home Appliances – October 2013

4

CanopyInstallationandOperationManual

Warning: Failure to install the screws or fixing device in accordance with these
instructions may result in electrical hazards

Home Appliances – October 2013

5

CanopyInstallationandOperationManual

If the model with Glass:

3.1 The cooker hood shall be placed at a
distance of 65-75cm (26-30inch) from the
cooking surface. See Pic 1.

3.2 Install the hook on a suitable place once the
installation height is fixed, and keep it in line. The
fixed position of the inside chimney bracket is
the place of chimney. See Pic 2.

3.3 Fix one-way valve on the hood and connect
the extensible pipe to the one-way valve. See
Pic 3.

3.4 Put the cooker hood on the hook. See Pic 4.

3.5 Put the glass according to the lead direction
and way on the cooker hood, and then use the screws to fix the glass. See Pic 5.

3.6 Use clamp to fix the T-piece valve on the extensible pipe. See Pic 5.

3.7 Fix plate on the outer chimney, and be sure that the inside chimney can be
adjusted the height in it freely, See Pic 6.

3.8 Install the chimney and screw the T-piece metal outlet to the inside chimney, See
Pic 7 and 8.

3.9 Adjust the height of the inside chimney to the position of the inside chimney
bracket and fix on it by screw, after adjusting the position, fix the body with safety
screw. See Pic 9.

Note: The two safety vents are positioned on the back casing, with diameter
of 6mm.

Home Appliances – October 2013

6

CanopyInstallationandOperationManual

Warning: Failure to install the screws or fixing device in accordance with these
instructions may result in electrical hazards

Home Appliances – October 2013

7

CanopyInstallationandOperationManual

(4) NOTICE OF INSTALLATION

1. Before installation, please ensure the area is clean to avoid suction of the

remaining bits of broken wood and dust.

2. It cannot share the same air ventilation tube with other appliance such as gas

tube, warmer tube, and hot wind tube.

3. The bending of ventilation tube should be≥120°, parallel or above the start

point and should be connected to the external wall.

4. After installation, make sure that the extractor is level to avoid grease

collection at one end.

Home Appliances – October 2013

8

CanopyInstallationandOperationManual

(5) SAFETY WARNING

 Keep your children from using the cooker hood.

 Your cooker hood is for domestic use only, not suitable for barbecue, roast shop

and other commercial use.

 Any installation work must be carried out by a qualified electrician or competent

person.

 The cooker hood and its filter mesh should be cleaned regularly in order to keep

in good working order.

 Before cleaning, always ensure that you have switched your cooker hood off.

 Clean the cooker hood according to the instruction manual and keep the

cooker hood from the danger of burning.

 No fire for drying your cooker hood.

 If there is any fault with your cooker hood, please call the service department

appointed by agent for servicing.

 Please keep the room draughty when your cooker hood and gas hob are

working.

 Do not exhaust the gas from cooker hood through the same heated flue which is

for the gas from gas hob and other kitchen appliances.

 Before installation and usage, read all the instructions and make sure that the

voltage (V) and the frequency (Hz) indicated on your cooker hood are exactly

the same as the voltage (V) and the frequency (Hz) in your home.

 In order to get the most out of your cooker hood, please read the instruction

manual before installing & using, and keep it in a safe place.

 Ensure that you could get our guarantee for your cooker hood, please provide

the warranty card and purchase receipt, or the guarantee will not be offered.

Home Appliances – October 2013

9

CanopyInstallationandOperationManual

（6） USE

Electronic Button

1. Turn on the power; the buzzer will buzz five times. The sound shows that the

appliance is powered.

2. Push the low button, the indicating light 1 on, the buzzer will buzz once, and

the motor runs at low speed. Push it again and the motor will stop.

3. Push the middle button, the indicating light 2 on, the buzzer will buzz once,

and the motor runs at mid speed. Push it again and the motor will stop

4. Push the high button, the indicating light 3 on, the buzzer will buzz once, and

motor runs on high speed. Push it again and the motor will stop

5. Push the light button; the indicating light 4 on, and the two lighting lamps will

come on. Push it again and the lamps will turn off, with every push the buzzer

will buzz one time.

Home Appliances – October 2013

10

CanopyInstallationandOperationManual

Push button

1. Push stop button, and the motor will stop.

2. Push the Low button, the buzzer will buzz once, and the motor runs at low speed.

3. Push the Mid button, the buzzer will buzz once, and the motor runs at mid speed.

4. Push the High button, the buzzer will buzz once, and the motor runs at high speed.

5. Push the light button and the two lights will come on. Push it again and the light

will turn off.

Ligh t

Ligh t

Stop

Stop

Stop

Low

Low

Low

Mid

Mid

Mid

High

High

High

Ligh t

pic6C

pic6C

pic6C

Home Appliances – October 2013

11

CanopyInstallationandOperationManual

LCD Electronic button

Pic 7

1. Plug the hood; LCD will display 24-hour system with blue backlight. Backlight will

be extinguished after 30 seconds without any operation.

2. Press “

” button once; lights will be on and LCD will show “ ”. Press “ ”

button again; lights will be off and “

3. Press “

and “

speed. Press “

“

pressing “

now; press the “

” button once; the hood works at LOW speed and LCD will show “ ”

” button will be on. Press “ ” button again; the hood works at MEDIUM

” button one more time; the hood works at HIGH speed. Press

” button again; the hood works at LOW speed again and it repeat. While

” button; the “ ” button is always on. If you want to stop the hood

” button once.

4. When the hood is not working; press “

speed it works last time and LCD will show “

hood stop working and “

” will disappear from LCD.

” on LCD will disappear.

” button once. The hood will work at the

”. Press “ ” button again; the

5. When both “

time-setting. Press “

and

flashes; which represents hour. Press “ ” button once the number adds

by 01. Continue pressing “

LCD shows 23; it doesn’t work by pressing “

” button and “ ” button don’t work; “ ” button is used for

” button for 2 to 3 seconds; will be shown on LCD

” button; it will display from 13;14… until 23. When

” button. Press “ ” button once;

the number reduces by 01. When LCD shows 00; it doesn’t work by pressing “

button. After setting hour; you can start setting minute by pressing “ ” button

again.

number adds by 01. Continue pressing “

until 59. When LCD shows 59; it doesn’t work by pressing “

Home Appliances – October 2013

on LCD flashes; which represents minutes. Press “ ” button once the

” button; it will display from 01;02…

” button. Press “ ”

12

”

CanopyInstallationandOperationManual

button once; the number reduces by 01. When LCD shows 00; it doesn’t work by

pressing “

When “

” button. After setting hour and minute; press “ ” to confirm.

” button doesn’t work; “ ” button is used for delay timer function. Delay

timer function allows you to set the hoods automatically power off according to the

delay timer you set from 1 minute to 60 minutes. Press “

delay timer setting and LCD shows

adds by 01. Continue pressing “

” button; it will display from ;

. Press “ ” button once the number

” button once; it enters for

; … until Press “ ” button once; the number

reduces by 01. After setting delay timer you want; press “

” button to confirm. If
you set delay timer as 05:00; the LCD display will show from 05:00; 04:59… until 00:01
00:00. When LCD shows 00:00; the hood will automatically power off and LCD display
will only show 24-hour system with blue backlight. After 30 seconds without operation;
blue backlight will disappear. But please note the Lamp is not under control of delay

timer. Next time; if you want to use delay timer function and you press “

” button
without any change on time. The hood will automatically count time down from your
previous setting after 5 seconds.

Home Appliances – October 2013

13

CanopyInstallationandOperationManual

LCD Touch control

Pic 8

1. Power on: Switch on the power supply, and the backlight is lit, displaying “24-

hour system”. The output is then blocked up,and the soot machine enters
standby status. The backlight disappear automatically 30 seconds later under
the condition of none operation.

2. Press “Indicator” key: Press the indicator key once, the indicator is lit, and

the LCD screen is lit. Press it for a second time,

of the indicator and the LCD

screen will distinguish and it will be repeated again and again.

3. Power on position and increase key

, the motor is provided with three positions,

i.e. low, medium and high.

1. Press
starts operation. The

2. Press
display screen, and the

3. Press
the display screen, and the

4. Go on pressing

key once, the is displayed on the display screen, and the motor

is the low position (power on position.)

key once more at the low position, the is displayed on the

is the medium position.

key once more at the medium position, the is displayed on

is the high position.

key at the high position, the is still displayed on
the display screen, and the motor works normally. It is still at high position at
this time.

4. Power on position and decrease key “

”

on

1. Press “

” key once, the motor is adjusted to a lower position, and the LCD
screen displays that position in the meantime; If it is decreased continuously
to none position, then, it is the power off position (namely, the motor stops
operation.)

5. Timer key “

”:

1. The timer key is the timer setting key if the timer key doesn’t work at both the
position and indicator.

 Long press timer key

for 2-3 seconds, time segment , and the

first two hour bit segment flash, use key for the digit increase, and use

key for the digit decrease. Namely: The variable is 01 each time it is

pressed; the hour segment is with the largest digit of 23. If it exceeds 23,

Home Appliances – October 2013

14

CanopyInstallationandOperationManual

key is null and void. If it is equal to 00, then, the key is null and

void.

 Press the timer key for the 2

two minute bit segment flash, use

nd

time , time segment , and the last

key for the digit increase, and use

key for the digit decrease. Namely: The variable is 01 each time it is

pressed; the minute segment is with the largest digit of 59. If it exceeds

key is null and void. If it is equal to 00, then, the key is null and

59,
void.

 Press the timer key

for the 3rd time, and it is the time setting exit and

confirm key.

 Long press timer key

for 2-3 seconds under this operation mode, and it
is for the hour setting; Press it for the 2nd time: Setting for the minute;
Press it for the 3
be repeated again and again (if the 1

rd

time: For the time setting exit and confirm, and it will

st

time pressing doesn't exceed 2

seconds, then it can't run this operating procedure.)

2. The timer key is the timer if the timer key works at either the position or the
indicator.

 It is provided with three kinds of time segment, and they are

st

5min/15min/30min/timer cancel in sequence, and the 1

nd

the 2
the 5

time is 15min, the 3rd time is 30min, the 4th time is timer cancel,

th

time is 5min, and the 6th time is 15min …., and it will be repeated

time is 5min,

again and again.

 Example: Let the setting time be 15min, the display is 00:15, 00:14, …00:1,

with 0:00 displays per minute, and once “00: 00” appears, the motor
position and the indicator power supply will be cut off automatically,
(the display screen displays “24-hour system”, the output is blocked up,
and the soot machine enters standby status, and the backlight will be
put out automatically 30 seconds later.)

 Time segment change over, 5 seconds later, it starts to decrease

gradually (example: 15min is changed over to 30min, with a delay of 5
seconds, and 00: 30 on the display screen starts to decrease gradually).

Home Appliances – October 2013

15

CanopyInstallationandOperationManual

(7) MAINTENANCE

7.1 The cleaning of the carbon grease filter mesh

The filter mesh is made of high-density stainless steel. Please do not use the corrosive
detergent on it. Keeping this filter clean will keep the appliance running correctly.
Please strictly follow the guidelines below.

Method 1: Put the mesh into 40-50 c clean water, pour on detergent, and soak for 2­3 mins. Wear gloves and clean with a soft brush. Please do not apply too much
pressure, as the mesh is delicate and will damage easy.
Method 2: If instructed to do so, it can be put into a dishwasher, set the temperature
at around 60 degrees.

7.2 Notice of cleaning cooker hood

A. To protect the main body from corrosion over a long period of time, the

cooker hood should be cleaned with hot water plus non corrosive detergent
once a month. The hood should be wiped off with dry clean cloth after
cleaning is done.

B. Please do not use abrasive detergent for it will damage the body.
C. Keep the motor and other spare parts free from water, as this will cause

damage to the appliance.

D. Before cleaning the appliance please remember to turn off power
E. The carbon filter shouldn’t be exposed to heat.
F. Please don’t tear open the fixed bar around the carbon filter
G. If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

Home Appliances – October 2013

16

CanopyInstallationandOperationManual

(8) LIGHT REPLACEMENT

8.1 Halogen lighting:

Use a small flat blade screwdriver to remove the inner stainless steel ring (when
removing the inner ring, do so carefully so not to damage the range hood, as the
glass lens could easily fall out of the inner ring) ; and remove carefully the halogen
globe with a new one.

8.2 LED lighting:

NOTE: Power needs to be disconnected for replacement of LED lights as access is

required to loosen the cord restraints to undergo this procedure. The LED lamp
assembly should be ordered directly from the supplier of the canopy hood.

Remove the filters, and push the light downwards, and unplug the wiring connector.
Reverse the procedure to place the new light assembly into position.

Home Appliances – October 2013

17

（9） Abnormity and Solution

Fault

Cause Solution

CanopyInstallationandOperationManual

The leaf blocked Get rid of the blocking

Light on, but motor

The capacitor damaged Replace capacitor

does not work

The motor jammed bearing
damaged
The internal with of motor off or
a bad smell from the motor

Beside the above mentioned, check the following:
Light does not work,
motor does not work

Light damaged Replace lights

Power cord looses Connect the wires as per

Oil leakage

One way valve and the air

ventilation entrance are not

tightly sealed

Leakage from the connection

of U-shaped section and

cover
Shake of the body The leaf damaged and causes

shaking

The motor is not tightly

hanged

The body is not tightly

hanged
Insufficient suction The distance between the

body and the gas top too long

Too much ventilation from

open doors or windows

Replace motor

Replace motor

the electric diagram
Take down the one way
valve and seal with glue

Take U-shaped section
down and seal with soap
or paint
Replace the leaf

Lock the motor tightly

Fixed the body tightly

Readjust the distance

Choose a new place and
resemble the machine

The machine inclines The fixing screw not tight

enough

The hanging screw not tight

enough

Home Appliances – October 2013

18

Tighten the hanging
screw and make it
horizontal
Tighten the hanging
screw and make it
horizontal

CanopyInstallationandOperationManual

Your Canopy hood details

Date of purchase

Model Number

Invoice Number

Invoice Date

Purchased from

Date Installed

THE REST OF THIS PAGE IS LEFT BLANK INTENTIALLY

Home Appliances – October 2013

19

PRODUCT SERVICE NUMBER

1800 805 300

web - [e-mail]

distributors of