Page 1
3880 KT
2960311391_EN/050916.1542
Page 2
Please read this user manual first!
Dear Customer,
Thank you for prefering a Arçelik product. We hope that your product which has been manufactured with high quality
and technology will give you the best results. We advise you to read through this manual and the other accompanying
documentation carefully before using your product and keep it for future reference. If you transfer the product to
someone else, give its manual as well. Pay attention to all details and warnings specified in the user manual and
follow the instructions given therein.
Use this user manual for the model indicated on the cover page.
Read the instructions.
Explanation of symbols
Throughout this user manual the following symbols are used:
Important information or useful hints about
usage.
C
Warning for hazardous situations with
regard to life and property.
A
Warning against electric shock.
B
Warning against hot surfaces.
Warning against fire hazard.
Packaging materials of the product are
manufactured from recyclable materials in
accordance with our National Environment
Regulations.
Do not dispose of the packaging wastes with the domestic waste or other wastes, discard them to the dedicated
collection points designated by the local authorities.
This product was manufactured using the latest technology in environmentally friendly conditions.
WEEE It complies with the WEEE Directive
Page 3
1 Important instructions for safety and environment
This section contains safety instructions that will help protect from risk of
personal injury or property damage. Failure to follow these instructions shall
void any warranty.
1.1 General safety
• The dryer can be used by children at and above 8 years old and by
persons whose physical, sensory or mental capabilities were not fully
developed or who lack experience and knowledge provided that they
are supervised or trained on the safe usage of the product and the risks
it brings out. Children should not play with the product. Cleaning and
maintenance works should not be performed by children unless they are
supervised by someone.
• Children of less than 3 years should be kept away unless continously
supervised.
• Adjustable feet should not be removed. The gap between the dryer and
the floor should not be reduced with materials such as carpet, wood and
tape. This will cause problems with the dryer.
• Always have the installation and repairing procedures carried out by the
Authorized Service. Manufacturer shall not be held liable for damages
that may arise from procedures carried out by unauthorized persons.
• Never wash the dryer by spraying or pouring water onto it! There is the
risk of electric shock!
Dryer / User Manual
EN 3 /
Page 4
Important safety and environmental instructions
1.1.1 Electrical safety
Electrical safety instructions should be followed while electrical
A
A
• Connect the dryer to a grounded outlet protected by a fuse at the value
specified on the type label. Have the grounding installation performed by
a qualified electrician. Our company shall not be liable for any damages
that will arise when the dryer is used without grounding in accordance
with the local regulations.
• The voltage and allowed fuse protection is stated on the type label plate.
• The voltage specified on the type label must be equal to your mains
voltage.
• Unplug the dryer when it is not in use.
• Unplug the dryer from the mains during installation, maintenance,
cleaning and repair works.
connection is made during the installation.
The appliance must not be supplied through an external switching
device, such as a timer,or connected to a circuit that is regularly
switched on and off by utility.
• Do not touch the plug with wet hands! Never unplug by pulling on the
cable, always pull out by grabbing the plug.
• Do not use extension cords, multi-plugs or adaptors to connect the dryer
to power supply in order to decrease the risk of fire and electric shock.
• Power cable plug must be easily accessible after installation.
Damaged mains cable should be changed notifying the Authorized
B
B
EN 4 /
Service.
If the dryer is faulty, it must not be operated unless it is repaired
by an authorized service agent! There is the risk of electric shock!
Dryer / User Manual
Page 5
Important safety and environmental instructions
1.1.2 Product safety
Points to be taken into consideration for fire hazard:
Below specified laundry or items must not be dried
in the dryer considering fire hazard.
• Unwashed laundry items
• Items soiled with oil, acetone, alcohol, fuel oil, kerosene, stain
removers, turpentine, paraffin or paraffin removers must be
washed in hot water with plenty of detergent before being dried
in the dryer.
For this reason especially the items containing the above specified
stains must be washed very well, to do this use adequate
detergent and choose a high washing temperature.
Below specified laundry or items must not be dried in the
dryer due to the fire hazard:
• Garments or pillows bolstered with rubber foam (latex foam),
shower bonnets, water resistant textiles, materials with rubber
reinforcement and rubber foam pads.
• Clothing cleaned with industrial chemicals.
Items such as lighter, match, coins, metal parts, needle etc.
may damage the drum set or may lead to functional problems.
Therefore check all the laundry that you will load into your dryer.
Never stop your dryer before the programme completes. If you
must do this, remove all laundry quickly and lay them out to
dissipate the heat.
Clothes that are washed inadequately may ignite on their own and
even may ignite after drying ends.
• You must provide enough ventilation in order to prevent gases exiting
from devices operating with other types of fuels including the naked flame
from accumulating in the room due to the back fire effect.
Dryer / User Manual
EN 5 /
Page 6
Important safety and environmental instructions
Underwear that contains metal reinforcements should not be dried
A
C
C
• Never attempt to repair the dryer by yourself. Do not perform any repair
or replacement procedures on the product even if you know or have the
ability to perform the required procedure unless it is clearly suggested in
the operating instructions or the published service manual. Otherwise,
you will be putting your life and others’ lives in danger.
• There must not be a lockable, sliding or hinged door that may block
the opening of the loading door in the place where your dryer is to be
installed.
• Install your dryer at places suitable for home use. (Bathroom, closed
balcony, garage etc.)
in the dryer. Dryer may be damaged if metal reinforcements come
loose and break off during drying.
Use softeners and similar products in accordance with the
instructions of their manufacturers.
Always clean the lint filter before or after each loading. Never
operate the dryer without the lint filter installed.
• Make sure that pets do not enter the dryer. Check the inside of the dryer
before operating it.
• Do not lean on the loading door of your dryer when it is open, otherwise it
may fall over.
• The lint must not be allowed to accumulate around the tumble dryer
EN 6 /
Dryer / User Manual
Page 7
Important safety and environmental instructions
1.2 Mounting over a washing machine
• A fixing device should be used between the two machines when installing
the dryer above a washing machine. The fitting device must be installed
by the authorized service agent.
• Total weight of the washing machine and the dryer -with full load- when
they are placed on top of each other reaches to approx. 180 kilograms.
Place the products on a solid floor that has sufficient load carrying
capacity!
Washing machine cannot be placed on the dryer. Pay attention
A
Dryer Depth
to the above warnings during the installation on your washing
machine.
Installation Table for Washing Machine and Dryer
Washing Machine Depth
62 cm 60 cm 54 cm 50 cm 49 cm 45 cm 40 cm
54 cm
60 cm
Can be installed
Can be installed
Can be
installed
Cannot be
installed
Cannot be
installed
Dryer / User Manual
EN 7 /
Page 8
Important safety and environmental instructions
1.3 Intended use
• Dryer has been designed for domestic use. It is not suitable for
commercial use and it must not be used out of its intended use.
• Use the dryer only for drying laundry that are marked accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage
or transportation.
• The service life of the dryer that you purchased is 10 years. During this
period, original spare parts will be available to operate the dryer properly.
1.4 Child safety
• Packaging materials are dangerous for the children. Keep packaging
materials away from children.
• Electrical products are dangerous for the children. Keep children away
from the product when it is operating. Do not let them tamper with the
dryer. Use the child-proof lock in order to prevent the children to tamper
with the dryer.
Child-proof lock is on the control panel.(See Child lock)
C
• Keep loading door closed even when the dryer is not in use.
EN 8 /
Dryer / User Manual
Page 9
Important safety and environmental instructions
1.5 Compliance with the WEEE regulation
and disposing of the waste product
This product complies with EU WEEE Directive (2012/19/EU). This
product bears a classification symbol for waste electrical and
electronic equipment (WEEE).
This product has been manufactured with high quality parts and
materials which can be reused and are suitable for recycling. Do
not dispose of the waste product with normal domestic and other wastes at
the end of its service life. Take it to the collection center for the recycling of
electrical and electronic equipment. Please consult your local authorities to
learn about these collection centers.
1.6 Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive
(2011/65/EU). It does not contain harmful and prohibited materials
specified in the Directive.
1.7 Package information
Packaging materials of the product are manufactured from recyclable
materials in accordance with our National Environment Regulations. Do
not dispose of the packaging materials together with the domestic or other
wastes. Take them to the packaging material collection points designated
by the local authorities.
Dryer / User Manual
EN 9 /
Page 10
Important safety and environmental instructions
1.8 Technical Specifications
EN
Height (Min. / Max.) 84,6 cm / 86,6 cm*
Width 59,5 cm
Depth 60,9 cm
Capacity (max.) 8 kg**
Net weight (plastic front door usage) 49 kg
Net weight (glass front door usage) 51 kg
Voltage
See type label***Rated power input
Model code
* Min. height: Height with adjustable feet are closed.
Max. height: Height with adjustable feet are opened maximum.
** Dry laundry weight before washing.
*** Type label is located behind the loading door.
C
C
C
EN 10 /
Technical specifications of the dryer are subject to specification
without notice to improve the quality of the product.
Figures in this manual are schematic and may not match the
product exactly.
Values stated on markers on the dryer or in the other published
documentation accompanying with the dryer are obtained in
laboratory in accordance with the relevant standards. Depending
on operational and environmental conditions of the dryer, these
values may vary.
Dryer / User Manual
Page 11
2
Your Dryer
2.1 Overview
11
1
10
9
8
7
1. Top panel
2. Control panel
3. Loading door
4. Kick plate opening button
5. Ventilation grids
6. Adjustable legs
7. Kick plate
8. Type label
9. Lint filter
10. Water tank drawer
11. Power cord
2
3
4
5
6
Dryer / User Manual
EN 11 /
Page 12
Your Dryer
2.2 Package Contents
1
2 3
1. Water drain hose *
2. Filter drawer spare sponge*
3. User Manual
4. Drying basket*
5. Drying basket user manual*
*It can be supplied with your machine depending on its model.
4
5
EN 12 /
Dryer / User Manual
Page 13
3 Installation
Refer to the nearest Authorized Service Agent for
installation of the product. To make the product ready for
use, make sure that the electricity and water drainage
systems are appropriate by reading the information/
instructions given in the user manual before calling
the Authorized Service Agent. If they are not, call a
qualified technician and plumber to have any necessary
arrangements carried out.
Preparation of the product's location
C
B
A
as well as the electrical, clean water
and waste water installations is under
customer's responsibility.
CAUTION: Installation and electrical
connections of the product must be
performed by the Authorized Service
Agent. Manufacturer shall not be held
liable for damages that may arise from
procedures carried out by unauthorized
persons.
CAUTION: Prior to installation, visually
check if the product has any defects on
it. If so, do not have it installed. Damaged
products cause risks for your safety.
3.1 Appropriate installation location
• Install the product on a stable and level surface.
• Dryer is heavy. Do not move it by yourself.
• Operate your product in a well ventilated, dust-free
environment.
• Do not block the air ducts in front of and under
the product with materials such as long pile rugs,
wooden blocks and bands.
• Do not install the product behind a door with a
lock, sliding door or a hinged door which can strike
the product.
• Once the product is installed, it should stay at
the same place where its connections have been
made. When installing the product, make sure
that the rear wall of it does not touch anywhere
(tap, socket, etc.). Also pay attention to select an
installation location which you will not be required
to change afterwards.
• Place the product at least 1.5 cm away from the
edges of other furniture.
• The rear surface of the tumble dryer shall be
placed against a wall.
CAUTION: Do not place the product on top
B
of the power cord.
3.2 Removing the transportation
safety assembly
CAUTION: Remove the transportation
A
1. Open the loading door.
2. There is a nylon bag inside the drum that contains a
piece of styrofoam. Hold it from its section marked with
XX XX.
3. Pull the nylon towards yourself and remove the
transportation safety assembly.
A
safety assembly before using the product
for the first time.
CAUTION: Check that no part of the
transportation safety assembly remains
inside the drum.
3.3 Under counter installation
This product can be installed under a counter if the
height of the counter is sufficient.
CAUTION: While using the under counter
A
Stock number of under-
bench installation part
Leave at least 3 cm of space around the sides and the
dryer, never operate the dryer without
under counter installation part.
Dryer Depth 60 cm 54 cm
2979700200 2973600200
rear wall of the product when installing it under a
counter or in a cupboard.
Dryer / User Manual
EN 13 /
Page 14
Installation
3.4 Connecting to the drain
In products equipped with condenser unit, water
accumulates in the water tank during the drying cycle.
You should drain accumulated water after each drying
cycle.
You can directly drain accumulated water through the
water drain hose supplied with the product instead of
periodically draining the water collected in the water
tank.
1
2
3.5 Adjusting the feet
In order to ensure that the product operates more silently
and vibration-free, it must stand level and balanced on
its feet. Balance the machine by adjusting the feet.
Turn the feet to left or right until the machine stands level
and firmly.
3 4
Connecting the water drain hose
1-2 Pull hose at the behind of the dryer by hand in
order to disconnect it from where it is connected.
Do not use any tools to remove the hose.
3 Connect one end of the drain hose supplied with
the dryer to the connection point from where you
removed the hose of the product in previous step.
4 Connect the other end of the drain hose directly to
the wastewater drain or to the washbasin.
CAUTION: Hose must be fixed in every
A
C
C
type of connection. Your house will be
flooded if the hose comes loose during
water discharge.
Attach the water drain hose to a height of
maximum 80 cm.
Make sure that the water drain hose is not
stepped on, twisted or bent between the
drain and the machine.
CAUTION: Never unscrew the adjustable
A
feet from their housings.
3.6 Electrical connection
For specific instructions for electrical connection required
during installation (see 1.1.1 Electrical Safety)
CAUTION: If the product is faulty, it must
B
not be operated unless it is repaired!
There is the risk of electric shock!
3.7 Transportation of the product
1. Unplug the product before transporting it.
2. Remove the water drain (if any) and chimney
connections.
3. Drain the water in the product completely.
EN 14 /
Dryer / User Manual
Page 15
Installation
3.8 Warnings about sounds
It is normal to hear a metallic noise
C
C
from the compressor sometimes during
operation.
Water collected during operation is
pumped to water tank. It is normal to hear
pumping noise during this process.
3.9 Changing the illumination lamp
In case an illumination lamp is used in your laundry dryer
To change the Bulb/LED used for illumination of your
tumble dryer, call your Authorized Service.
The lamp(s) used in this appliance is not suitable for
household room illumination. The intended purpose of
this lamp is to assist the user to place laundry in the
tumble dryer in a comfortable way. ‘’The lamps used
in this appliance have to withstand extreme physical
conditions such as vibrations and temperatures above
50 °C.’’
Dryer / User Manual
EN 15 /
Page 16
4 Preparation
4.1 Laundry suitable for drying in the dryer
Always obey the instructions given on the garment tags. Dry only the laundry having a label stating that they are
suitable for drying in a dryer and make sure that you select the appropriate programme.
LAUNDRY DRYING SYMBOLS
Drying
Symbols
Drying
Settings
Iron -
Dry or Steam
IRON
Maximum temperature
Suitable for
dryer
At any temperature
No Iron
At high temperature
At medium
temperature
Iron at high
temperature
200 0C 150 0C 110 0C
4.2 Laundry not suitable for drying in
the dryer
Delicate embroidered fabrics, woollen, silk
garments, delicate and valuable fabrics,
C
airtight items and tulle curtains are not
suitable for machine drying.
4.3 Preparing laundry for drying
• Laundry may be tangled with each other after
washing. Separate the laundry items before placing
them into the dryer.
• Dry garments having metal accessories such as
zippers, inside out.
• Fasten the zippers, hooks and buckles and button
sheets.
Sensitive /
Delicate dry
At low temperature
Iron at medium
temperature
Without heating
Do not dry
with dryer
Hang to dry
Iron at low
temperature
Lay to dry
Do not dry
Hang wet to dry
Do not iron
Lay in shadow
4.4 Things to be done for energy
saving
• Following information will help you use the dryer in
an ecological and energy-efficient manner.
• Spin your laundry at the highest speed possible
when washing them. Thus, the drying time is
shortened and energy consumption is reduced.
• Sort out the laundry depending on their type and
thickness. Dry the same type of laundry together.
For example thin kitchen towels and table clothes
dries earlier than thick bathroom towels.
• Follow the instructions in the user manual for
programme selection.
• Do not open the loading door of the machine during
drying unless necessary. If you must certainly open
the loading door, do not to keep it open for a long
time.
• Do not add wet laundry while the dryer is in
operation
• Clean the lint filter before or after each drying
cycle. (See 6.1 Cleaning Lint Filter / Loading
Door Inner Surface)
Do not dry-
clean
to dry
Iron without
Dry-cleanable
steam
EN 16 /
Dryer / User Manual
Page 17
• Clean the filter periodically when there is visible
air collection on it or when the symbol lights up, if
there is a filter drawer cleaning warning symbol «
» available. (See 6. 4 Cleaning the filter
drawer)
• Ventilate the room, where the dryer is located, well
during drying.
4.5 Correct load capacity
Follow the instructions in the “Programme selection and
consumption table”. Do not load more than the capacity
values stated in the table.
It is not recommended to load the dryer
with laundry exceeding the level indicated
C
in the figure. Drying performance will
degrade when the machine is overloaded.
Furthermore, dryer and the laundry can get
damaged.
Following weights are given as examples.
Laundry
Cotton quit covers (double) 1500
Cotton quit covers (single) 1000
Bed sheets (double) 500
Bed sheets (single) 350
Large tablecloths 700
Small tablecloths 250
Tea napkins 100
Bath towels 700
Hand towels 350
Blouses 150
Cotton shirts 300
Shirts 250
Cotton dresses 500
Dresses 350
Jeans 700
Handkerchiefs (10 pieces) 100
T-Shirts 125
*Dry laundry weight before washing.
Approximate weights
(g)*
Dryer / User Manual
EN 17 /
Page 18
5 Program selection and operating your machine
5.1 Control Panel
21 3 4 5 6
1. On/Off/Cancel button
2. Program button
3. Program number indicator
4. Sound warning level button/child lock
5. Remaining time indicator
6. Delayed operation setting LED
7. Start/Stand-by button
8. Time delay selection button
78
EN 18 /
Dryer / User Manual
Page 19
Operating the product
5.2 Preparing the Machine
1. Plug the machine“
2. Place laundry into the machine.
3. Press On/Off/Cancel button for 1 second (long).
4. When your machine is turned on for the first time,
it turns on with the declaration program (cotton
wardrobe dry).
Pressing the On/Off/Cancel button does
C
not mean that the program started. Press
the Start / Stand-by button to start the
program.
5.3 Program selection
1. Determine the suitable program from the table
below where drying levels are presented.
2. Use the Program Selection button to select the
program you wish.
Only cotton clothes are dried under
normal temperature. Thick and multi-
Extra Dry
Wardrobe Dry
Iron Dry
C
layered laundry (towels, bed sheets,
denim trousers etc.) are dried so
that they can be placed in wardrobe
without ironing.
Normal laundry (tablecloths,
underwear etc.) are dried so that
they can be placed in wardrobe
without ironing.
Normal laundry (shirts, dresses etc.)
are dried to be ready for ironing.
For detailed program information, see
„Program selection and consumption
chart“..
5.4 Main programs
The following main programs are available depending on
fabric type.
• Cotton
Dry durable laundry with this program. It dried under
normal temperature. It is recommended for your cotton
laundry (bedsheets, bedding, towel, bathrobe etc.)
• Synthetic
Dry sensitive laundry with this program. It is
recommended for your synthetic laundry.
5.5 Additional programs
The following additional programs are available in the
machine for special situations.
Additional programs may vary depending
C
• Mixed
Use to dry synthetic and cotton clothes that don›t give
out colour together.
C
• Shirt
Dries shirts more delicately and causes less wrinkles for
easy ironing.
C
• Jeans
Use to dry denim clothes wrung in the washing machine
with high speed.
• Sport
Use to dry clothes made out of synthetic, cotton or mixed
fabrics.
• Daily
The program used for daily drying of cotton and synthetic
clothes.
• Shirt 30’
Use this program to prepare 2 shirts ready for ironing in
30 minutes.
• Delicates
You can dry your delicate clothes suitable for drying
or clothes that are recommended for hand wash (silk
blouses, thin underwear etc.) under low temperatures.
C
• Refresh
Ventilates for 10 minutes without blowing hot air. You
can ventilate the cotton and linen clothes that have been
enclosed for a long time with this program to remove
their odour.
on the features of your machine.
To get better results from drying
machine programs, your laundry should
be washed with suitable program in
your washing machine and wrung with
recommended wringing speed.
Shirt might remain slightly damp at the
end of the program. It is recommended
not to leave the shirts inside the drying
machine.
It is recommended to dry your delicates
in a laundry bag to prevent wrinkles and
damage. When the program ends, take
out your laundry immediately and hang
them to prevent wrinkles.
Dryer / User Manual
EN 19 /
Page 20
Operating the product
• Timer programs
You can select the 30 mins or 45 mins timer program
to achieve the desired final drying level under low
temperature.
In this program, the machine dries for
C
the duration set, regardless of the drying
level.
EN 20 /
Dryer / User Manual
Page 21
Operating the product
Program selection and consumption chart
EN
Programmes Capacity (kg)
Cottons / Coloreds
Extra dry 8 1000 % 60
A
Cupboard dry 8 1000 % 60
A
Iron dry 8 1000 % 60
A
Shirts 1,5 1200 % 60 50
Jeans 4 1200 % 50 120
Daily 4 1200 % 50 90
Sport 4 1000 % 60 105
Express 1 1200 % 50 45
Shirts 30 0,5 1200 % 60 30
Mixed 4 1000 % 60 90
Delicates 2 600 % 40 55
Synthetics
Cupboard dry 4 800 % 40
B
Iron dry 4 800 % 40
B
Energy consumption values
Programmes Capacity (kg)
Cottons linen Ready to wear*
Cottons Ready to iron 8 1000 % 60 1,50
Synthetics Ready to wear 4 800 % 40 0,75
Power consumption of the off-mode for the standard cotton programme at full load, PO (W) 0,5
Power consumption of the left-on mode for the standard cotton programme at full load, PL (W) 1,0
Contains fluorinated greenhouse gases covered by the Kyoto Protocol. Hermetically sealed. R134a / 0,38 kg
8 1000 % 60 1,92
Spin speed in washing
machine (rpm)
Spin speed in washing
machine (rpm)
Approximate amount of
remaining humidity
Approximate amount of
remaining humidity
Drying time
(minutes)
190
179
150
70
55
Energy con-
sumption value
kWh
„Cotton cupboard dry Programme“ used at full and partial load is the standard drying Programme
to which the information in the label and the fiche relates, that this Programme is suitable for drying
normal wet cotton laundry and that it is the most efficient Programme in terms of energy consumption
for cotton.
* : Energy Label standard program (EN 61121:2012)
All the values on the chart are identified according to EN 61121:2012 standard. Consumption values may vary from
the valued in the chart depending on laundry type, wringing speed, ambient conditions and voltage levels.
Dryer / User Manual
EN 21 /
Page 22
Operating the product
5.6 Auxiliary functions
Audible warning
Machine makes an audible warning when the
program is completed. To adjust the sound level, use the
Sound Warning Level button.
You can change the sound level before
C
5.7 Warning indicators
C
Filter cleaning
When the program is completed, the warning indicator
for filter cleaning turns on.
Water tank
When the program is completed, the warning indicator to
empty the water tank turns on.
If the water tank fills up while the program continues,
the warning indicator starts flashing and the machine
goes into stand-by. In this case, empty the water tank
and start the program by pressing the Start / Stand-
by button. Warning indicator turns off and program
resumes.
Time delay
You can delay the start of the program for up to 24 hours
using the Time Delay function.
1. Open the loading door and place the laundry.
2. Select the drying program.
3. Press the Time Delay selection button and set the
4. Press the Start / Stand-by button. Time Delay
C
the program starts or while the program
continues..
Warning indicators may vary depending
on the model of your machine.
delay time you wish. Time Delay LED turns on. (If you
keep the button pressed, the time delay switches
continuously).
countdown begins.
You can add or remove laundry during
the Time Delay duration. At the end of the
Time Delay countdown, the Time Delay
warning indicator turns off and drying
begins
Changing the time delay duration
If you want to change the duration during the countdown:
1. Press the On/Off/Cancel button for 3 seconds to
cancel the program. Turn on the machine again and
repeat the Time Delay steps for the duration you
wish.
2. When your machine is turned on for the first time,
it turns on with the declaration program (cotton
wardrobe dry).
Cancelling the Time Delay function
If you want to cancel the Time Delay countdown and start
the program immediately:
1. Press the On/Off/Cancel button for 3 seconds to
cancel the program.
2. Press the On/Off/Cancel button to start you
previously selected program.
5.7 Starting the program
Press the Start/Stand-by button to start the program.
Start/Stand-by and Drying indicators turn on to show that
program started.
5.8 Child Lock
The machine has a child lock which prevents the
program flow from being interrupted when the buttons
are pressed during a program. When the child lock is
activated, all buttons on the panel except the On/Off/
Cancel button are deactivated.
To activate the child lock, keep the Sound Warning and
Child lock buttons pressed for 3 seconds.
The child lock has to be deactivated to be able to start a
new program after the current program is finished or to
be able to interfere with the program. To deactivate the
child lock, keep the same buttons pressed for 3 seconds.
When the child lock is activated, the child
C
C
When the child lock is active:
The machine runs, or in stand-by state the indicator
symbols won’t change upon changing the position of the
program selection button.
lock warning indicator on the screen
turns on.
Child lock deactivates when the machine
is turned off and on by the On/Off/
Cancel button.
EN 22 /
Dryer / User Manual
Page 23
Operating the product
5.9 Changing the program after it is
started
You can change the program you selected to dry your
laundry with a different program after the machine starts
running.
1. For example, to select Extra Dry instead of Iron Dry,
pause the program by pressing the Start / Stand-
by button for 1 second.
2. Select the Extra Dry program using the Program
selection knob.
3. Press the Start/Stand-by button to start the
program.
Adding and removing clothes during stand-by
If you want to add or remove clothes to/from the
machine after the drying program starts:
1. Press the Start/Stand-by button to put the machine
in Stand-by state. The drying operation stops.
2. Open the loading door while in Stand-by state, and
close the door after you remove or add laundry.
3. Press the Start/Stand-by button to start the
program.
Adding laundry after the drying operation
C
C
C
starts may cause the dried laundry inside
the machine to mix with wet laundry and
leave the laundry damp at the end of
operation.
Adding or removing laundry during drying
may be repeated as many times as you
wish. But this operation continuously
interrupts the drying operation, and thus
increases program duration and energy
consumption. So, it is recommended to
add laundry before the program starts.
If a new program is selected by turning
the program selection knob while the
machine is in stand-by; the running
program terminates and new program
information is displayed on the screen.
WARNING: Do not touch the inner
surface of the drum while adding or
removing clothes during a continuing
program. The drum surface is hot.
5.10 Cancelling the program
If you want to cancel the program and terminate the
drying operation for any reason after the machine starts
running, keep the On/Off/Cancel button pressed for 3
seconds.
WARNING: The inside of the machine
A
shall be extremely hot when you cancel
the program during machine operation,
so run the ventilation program to allow it
to cool down.
5.11 Program end
When the program ends, the Fibre Filter Cleaning and
Water Tank warning symbols on the program observation
indicator turn on. Loading door may be opened and
machine becomes ready for another run.
To turn off the machine, press the On/Off/Cancel
button.
If the laundry is not removed after the
C
C
C
program is completed, the wrinkle
prevention function activates for 2 hours
to prevent the laundry inside the machine
to get wrinkled. The program tumbles
the laundry with 10-minute intervals to
prevent them from wrinkling.
Clean the fibre filter after each drying.
(See „Fibre filter and Loading door inner
surface“)
Empty the water tank after each drying.
(See „Emptying the water tank“)
Dryer / User Manual
EN 23 /
Page 24
6 Maintenance and cleaning
Service life of product extends and frequently
experienced problems will be reduced if it is cleaned at
regular intervals.
6.1 Cleaning Lint Filter / Loading Door
Inner Surface
Lint and fibre released from the laundry to the air during
the drying cycle are collected in the Lint Filter.
Such fibre and lint are generally formed
C
A
C
To clean the lint filter:
• Open the loading door.
• Remove the lint filter by pulling it up and open the
• Clean lint, fibre, and cotton raveling by hand or with
• Close the lint filter and place it back into its
during wearing and washing.
Always clean the lint filter and the inner
surfaces of the loading door after each
drying process.
You can clean the lint filter housing with a
vacuum cleaner.
lint filter.
a soft piece of cloth.
housing.
• A layer can build up on the filter pores that can
cause clogging of the filter after using the dryer
for a while. Wash the lint filter with warm water
to remove the layer that builds up on the lint
filter surface. Dry the lint filter completely before
reinstalling it.
• Clean the entire inner surface of the loading door
and loading door gasket with a soft damp cloth.
EN 24 /
Dryer / User Manual
Page 25
Maintenance and cleaning
6.2 Cleaning the sensor
There are dampness sensors in the dryer that detect
whether the laundry is dry or not.
To clean the sensors:
• Open the loading doorof the dryer.
• Allow the machine to cool down if it is still hot due
to the drying process.
• Wipe the metal surfaces of the sensor with a soft
cloth, dampened with vinegar and dry them.
Clean metal surfaces of the sensors 4
C
C
A
times a year.
Do not use metal tools when cleaning
metal surfaces of the sensors.
Never use solvents, cleaning agents or
similar substances for cleaning due to the
risk of fire and explosion!
6.3 Draining the water tank
Dampness of the laundry is removed and condensed
during drying process and the water that arise
accumulates in the water tank. Drain the water tank after
each drying cycle.
Condensed water is not drinkable!
A
Never remove the water tank when the
A
If you forget to drain the water tank, the machine will
stop during the subsequent drying cycles when the water
tank is full and the Water Tank warning symbol will flash.
If this is the case, drain the water tank and press Start /
Pause button to resume the drying cycle.
To drain the water tank:
Pull the drawer and remove the water tank carefully.
program is running!
Dryer / User Manual
• Drain the water in the tank.
• If there is lint accumulation in the funnel of the
water tank, clean it under running water.
• Place the water tank into its seat.
If the direct water draining is used as
C
an option, there is no need to empty the
water tank.
EN 25 /
Page 26
Maintenance and cleaning
6.4 Cleaning the filter drawer
Lint and fiber that could not be captured by the lint filter
are blocked in the filter drawer behind the kick plate.
Warning light lights up periodically every 7 drying cycle
maximum for remi,nding purposes on the products
with filter drawer cleaning warning light « ».
A filter drawer foam placed on plastic is available inside
the filter drawer.
To clean the filter drawer:
• Press the kick plate button to open the kick plate.
• Take out the filter drawer sponge.
• Remove the filter drawer cover by turning it in the
direction of arrow.
• Pull out the filter drawer.
• Open the filter drawer by pressing the red button.
• Wash the filter drawer sponge by hand to remove
the fiber and lint on the surface. After washing the
sponge, squeeze it by hand and remove the excess
water. Well-dry the sponge before storing it.
It is not necessary to clean the sponge
if lint and fiber accumulation on it is not
C
• Place the sponge back into its place.
• Close the filter drawer as to lock the red button.
significant.
EN 26 /
Dryer / User Manual
Page 27
Maintenance and cleaning
• Place the filter drawer back into its place, turn the
filter drawer cover in the arrow direction and close
it securely.
• Close the kick plate cover.
Drying without the filter drawer sponge in
A
C
place will damage the machine!
A dirty lint filter and filter drawer will
cause longer drying periods and higher
energy consumption.
6.5 Cleaning the evaporator
Clean the lint accumulated on the fins of the evaporator
located behind the filter drawer with a vacuum cleaner.
You can also clean by hand provided that
you wear protective gloves. Do not attempt
A
to clean with bare hands. Evaporator fins
can harm your hand.
Dryer / User Manual
EN 27 /
Page 28
7 Troubleshooting
Drying process takes too much time.
• Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.
• Filter drawer may be blocked>>>clean the foam inside the filter drawer.
• Ventilation grids on the front side of the machine are blocked. >>> Remove the objects (if any) that block
ventilation in front of the ventilation grids.
• Ventilation is not sufficient since the room where the machine is installed is very small. Open the door and
window of the room to avoid the room temperature increase too much.
• Lime deposit has built up on the dampness sensor. >>> Clean the dampness sensor.
• Excessive laundry is loaded. >>> Do not load the dryer in excess.
• Laundry is not spun sufficiently. >>> Spin your laundry at a higher speed in your washing machine.
Laundry comes out wet at the end of drying.
C
After drying, the hot clothes feel damper than their actual dampness level.
• It is likely that the selected programme did not suit the laundry type.>>>Checking the care labels on clothes,
select appropriate programme for the laundry type or use timer programmes in addition.
• Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.
• Filter drawer may be blocked>>>clean the foam inside the filter drawer.
• Excessive laundry is loaded. >>> Do not load the dryer in excess.
• Laundry is not spun sufficiently. >>> Spin your laundry at a higher speed in your washing machine.
Dryer does not switch on or the programme does not start. Dryer does not start when it is set.
• It is not plugged in. >>> Make sure that the machine is plugged in.
• The loading door is ajar. >>> Make sure that the loading door is closed securely.
• Programme is not selected or the Start / Pause / Cancel button is not pressed. >>> Make sure that the
programme is selected and the machine is not in Pause mode.
• Childproof Lock is activated. >>> Deactivate the Childproof Lock.
Programme is interrupted without any cause.
• Loading door is ajar. >>> Make sure that the loading door is closed securely.
• There was a power failure. >>> Press Start / Pause / Cancel button to start the programme.
• Water tank is full. >>> Drain the water tank.
Laundry has shrunk, become felted or deteriorated.
• A programme suitable for the laundry type is not used. >>> Check the garment tag and select a programme
suitable for the fabric type.
Drum lighting does not turn on. (On models with lamp)
• Dryer is not switched on with the On / Off button. >>> Make sure that the dryer is switched on.
• Lamp is defective. >>> Call Authorized Service Agent to have the lamp replaced.
End/Anti-creasing symbol is on.
• Anti-creasing programme is activated in order to prevent laundry that has remained in the machine from
creasing. >>> Turn off the dryer and take out the laundry.
End symbol is on.
• Programme is over. Turn off the dryer and take out the laundry.
EN 28 /
Dryer / User Manual
Page 29
Troubleshooting
Lint Filter Cleaning symbol is on.
• Lint filter is not cleaned. >>> Clean the lint filter.
Lint Filter Cleaning symbol is flashing.
• Filter housing is clogged with lints. >>> Clean the lint filter housing.
• A deposit has built up on the lint filter pores that may cause clogging. >>> Wash the lint filter with warm
water.
• Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter drawer.
Water leaks from the loading door
• Lint has accumulated on the inner surfaces of the loading door and on the surfaces of the loading door
gasket. >>> Clean the inner surfaces of the loading door and the surfaces of the loading door gasket.
Loading door opens spontaneously.
• Loading door is ajar. >>> Push the loading door to close until you hear a locking sound.
Water Tank warning symbol is on/flashing.
• Water tank is full. >>> Drain the water tank.
• Water draining hose is bent. >>> If the product is connected directly to a wastewater drain, check the water
drain hose.
Filter Drawer Cleaning warning symbol is flashing.
• Filter drawer is not cleaned. >>> Clean the sponge and the filter cloth in the filter drawer.
If you cannot eliminate the problem although you follow the instructions in this section, consult your
A
dealer or the Authorized Service Agent. Never try to repair a nonfunctional product yourself.
Dryer / User Manual
EN 29 /
Loading...