Aqua One Cleaview 200, Cleaview 300, Cleaview 100, Cleaview 280, Cleaview 500 Instructions Manual
...
Cleaview
75, 100, 200, 280,
300, 500, 800
Instruction version: 19/03/2015
www.aquaone.com.au
2+1
Marine
Tropical
Coldwater
2
Important Safeguards
To guard against injury, basic safety precautions
should be observed, including the following:
1. Read and follow all safety instructions and important
notices in these instructions as well as on the product
itself.
2. This appliance is not intended for use by children
or inrm persons without supervision. Young children
should be supervised to ensure that they do not play
with the appliance.
3. To avoid possible electric shocks, special care
should be taken since water is employed in the use
of aquarium equipment. For each of the following
situations do not attempt repairs yourself. Return the
appliance to an authorised service facility for service or
discard the appliance.
a. If the appliance or any electrical component of the
appliance (non-immersible equipment only) falls into
the water or gets wet, do not reach for it. Unplug it and
then retrieve it.
b. If the appliance shows any sign of abnormal water
leakage, immediately unplug it from the power source.
c. Carefully examine the appliance after installation. It
should not be plugged in if there is water on parts which
are not intended to be wet.
d. Do not operate the appliance if it has a damaged
cord or plug, or if it is malfunctioning, or dropped or
damaged in any manner.
4. A “drip loop” (see graphic) should be arranged for
each cable connecting an aquarium to a power supply.
The drip loop is the part of the cable below the level of
the power supply. It prevents water travelling down the
cable and coming into contact with the power supply. If
the plug or the socket does get wet, do not unplug the
appliance. Disconnect the fuse or circuit breaker that
supplies the power to the appliance, then unplug and
examine for presence of water in the socket.
5. Always unplug the appliance from the electrical outlet
when not in use, before putting on or taking off parts,
before any type of maintenance or cleaning.
6. Never yank the cable to pull it from the socket. Pull
the plug carefully to disconnect.
7. Do not use the appliance for reasons other than
the intended use. The use of attachments that are not
recommended or sold by the manufacturer may cause
the product to be unsafe. This is not recommended.
8. Do not install or store the appliance where it will be
exposed to weather or temperatures below freezing.
9. Make sure any component mounted on a tank is
securely installed before operating it.
10. Ensure input voltage is the same voltage as your
local power supply.
11. If an extension cable is used it should have the
proper rating. Care should be taken to arrange the cord
so that it will not be tripped or pulled.
12. A G.F.C.I (Ground fault circuit interrupter) & surge
protector is recommended for all electrical appliances.
13. Ensure your hands are dry when turning the power
switch on/off and when inserting/removing the power
cable from the socket.
14. If you are in any doubt about the electrical installation
or safety of this product you must consult a qualied
electrician.
For Guarantee Conditions, please refer to the
Guarantee form that is enclosed with this product.
All products are supplied with tted plugs. This plug
should not be tampered with in any way or removed.
Removal or tampering with the plug invalidates our
guarantee offered with this product.
For UK a 3 pin adaptor is supplied with the product and
this must be used.
3
Before First Use / Preparation
Read and follow all the instructions, even if you feel
you are familiar with the product and nd a place to
keep the instructions handy for future reference.
Your attention is drawn particularly to the sections
concerning “IMPORTANT SAFEGUARDS” and the
“GUARANTEE CONDITIONS”. Please ensure you
retain your original purchase receipt in the event that
guarantee service is required.
Carefully unpack the product making sure you keep all
the packing material until all the parts of the product
have been found and the product has been assembled.
This product is shipped to you in a factory sealed
carton. Should the product malfunction in any way
or if the unit is damaged and requires replacement,
contact the retailer where the product was purchased
for inspection.
Replacement Parts & Filter Media
Use Aqua One Genuine Spare Parts Only. See
your local Aqua One Dealer and look for the
number listed below for the spare part you require.
Alternatively you will nd these numbers on the
silver label located on the product.
CV 75 Black Sponge 90s
CV 75 Carbon Cartridge 90c
CV 75 Impeller 90i
CV 100 Black Sponge 54s
CV 100 Carbon Cartridge 54c
CV 100 Impeller 54i
CV 200 Carbon Cartridge 46c
CV 200 Impeller 46i
CV 280 Carbon Cartridge 55c
CV 280 Impeller 55i
CV 300 Carbon Cartridge 47c
CV 300 Impeller 47i
CV 500 Carbon Cartridge 48c
CV 500 Impeller 48i
CV 800 Carbon Cartridge 49c
CV 800 Impeller 49i
Aqua One Spare Parts
54I
4
Know Your Filter 75 / 100
1. Dust Cover
2. Carbon Cartridge
3. Flow Controller
4. Sponge
5. Inlet U-Pipe
6. Filter Body
7. Impeller
8. Adjusting Wheel
9. Extension Tube
10. O-ring
11. Motor
12. Strainer
1
2
3
4
5
6
7
8
9
10
11
12
Clearview 100
1. Dust Cover
2. Carbon Cartridge
3. Flow Controller
4. Sponge
5. Inlet U-Pipe
6. Filter Body
7. Impeller
8. Extension Tube
9. O-ring
10. Motor
11. Strainer
1
2
3
5
4
7
6
8
9
10
11
Clearview 75
5
Know Your Filter 200-800
1. Dust Cover
2. Flow Controller
3. Inlet U-Pipe
4. Carbon Cartridge
5. Biogrid
6. Extension Tube
7. Strainer
8. Filter body
9. Impeller
10. O-ring
11. Motor
1
2
3
4
5
6
7
8
9
10
11
Clearview 200, 300, 500, 800
6
Installation
Clearview 75-100
1. Remove the lter lid to access the lter
body.
2. Place the inlet u-pipe into position. The
longer side of the pipe sits on the outside of
the lter body. The shorter side locks into the
impeller housing.
3.The extension tube then connects to the
inlet u-pipe. The strainer then attaches to the
extension tube. The strainer and extension
tube is the part that sits in the water of the
aquarium.
4. Wash the carbon cartridge in tap water
before use. DO NOT USE DETERGENT OR
SOAP. The carbon cartridge slides into the
furthest grooves with the wool
facing the rear of the lter.
(refer to the Diagram on the previous page)
5. The sponge slides in between the cartridge
and the front of the lter.
6. Push the adjusting wheel into the bottom
of the lter body. This is used to keep the
whole lter level from top to bottom, otherwise
the lter will slant away at the top and may
overow if the lter
cartridge becomes blocked.
7. Hang the lter off the back wall of the
aquarium with the extension tube and strainer
inside the aquarium water.
8. Fill the lter body with aquarium water until
it overows back into the aquarium. Turn on at
the power supply. It may take a little while to
start as it expels the air from the impeller.
9. Adjust the ow with the knob on the top
of the inlet u-pipe. It is better to leave at full
ow but if this current is too strong, turn down
slightly.
10. Place the lid back on the lter body.
Clearview 200-800
1. Remove the lter dust cover to access the
lter body.
2. Place the inlet u-pipe into position. The
longer side of the pipe sits on the outside of
the lter body. The shorter side locks into the
impeller housing.
3. Extend the extension tube from the longer
side of the inlet u-pipe.
4. The strainer then attaches to the extension
tube.
5. Wash the carbon cartridge in tap water
before use. DO NOT USE DETERGENT OR
SOAP. The carbon cartridge slides into the
furthest grooves with the wool
facing the rear of the lter. (refer to the Diagram
on the previous page)
6. The biogrid slides in between the cartridge
and the front of the lter.
7. Hang the lter off the back wall of the
aquarium with the extension tube and strainer
inside the aquarium water.
8. Fill the lter body with aquarium water until
it overows back into the aquarium.
9. Turn on at the power supply. It may take a
little while to start as it expels the air from the
impeller.
10. Adjust the ow with the knob on the top
of the inlet u-pipe. It is better to leave at full
ow but if this current is too strong, turn down
slightly.
11. Place the dust cover back on the lter
body.
7
Maintenance
1 - 2 WEEKS
1. Turn off at the power supply.
2. Remove the dust cover. Slide the carbon
cartridge out of the lter. Allow excess water
to run off. Rinse the cartridge under a high
powered tap to remove the trapped dirt.
3. Tip out dirty water from the lter body. Rell
the lter with aquarium water. Put carbon
cartridge back into position. Turn on at the
power supply.
It is important that the sponge/biogrid is not
cleaned or removed. If it starts to become
extremely dirty, just give them a gentle rinse
in a bucket of aquarium water, then put it back
in position.
6 - 8 WEEKS
1. Turn off at the power supply.
2. Remove entire lter from the back of the
aquarium and take to the sink.
3. Throw away the carbon cartridge and
replace with a new one. Wash the new
cartridge in tap water before use.
4. Remove the entire inlet u-pipe. Grasp the
motor and twist anti clockwise, then gently
pull down to completely remove it from the
lter body.
5. Remove the impeller from the motor and
wash. Use a double ended pipe brush and
clean the impeller well. (Where the impeller
sits).
6. Use an aquarium safe silicon lubricant and
apply to the O-ring seals around the motor.
This will allow easy removal of the motor for
the next service and provide a better water
seal.
7. Put the impeller back in place then reconnect
the motor to the lter body.
8. Clean the inlet u-pipe and extension tube
with a double ended pipe brush then put back
in place.
9. Hang the lter back in place and rell the
lter with aquarium water. Turn lter on at
power supply.
DO NOT CLEAN THE SPONGE/BIOGRID.
8
Specications
Correct Disposal of this product
This marking indicates that this product should not be disposed
with other household waste throughout the EU. To prevent harm
to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device, please use
the return and collection systems or contact the retailer where
the product was purchased. They can take this product for
environmental safe recycling.
Model: Clearview 75
Maximum Flow Rate: 190L/hr
Max Aquarium Volume: 30L
Power Requirements: 220 – 240V AC
Power Consumption: 2.5W
Suitable: Cold water, Tropical, Marine
Model: Clearview 100
Maximum Flow Rate: 180L/hr
Max Aquarium Volume: 40L
Power Requirements: 220 – 240V AC
Power Consumption: 3W
Suitable: Cold water, Tropical, Marine
Model: Clearview 200
Maximum Flow Rate: 200L/hr
Max Aquarium Volume: 60L
Power Requirements: 220 – 240V AC
Power Consumption: 3.5W
Suitable: Cold water, Tropical, Marine
Model: Clearview 280
Maximum Flow Rate: 280L/hr
Max Aquarium Volume: 80L
Power Requirements: 220 – 240V AC
Power Consumption: 4W
Suitable: Cold water, Tropical, Marine
Model: Clearview 300
Maximum Flow Rate: 300L/hr
Max Aquarium Volume: 80L
Power Requirements: 220 – 240V AC
Power Consumption: 5.2W
Suitable: Cold water, Tropical, Marine
Model: Clearview 500
Maximum Flow Rate: 500L/hr
Max Aquarium Volume: 120L
Power Requirements: 220 – 240V AC
Power Consumption: 5.8W
Suitable: Cold water, Tropical, Marine
Model: Clearview 800
Maximum Flow Rate: 800L/hr
Max Aquarium Volume: 200L
Power Requirements: 220 – 240V AC
Power Consumption: 9W
Suitable: Cold water, Tropical, Marine
9
Aqua One - Guarantee 2 + 1 Year
The additional 1 Year Extended Guarantee applies when you REGISTER online
with Aqua One. Register your Extended Guarantee at www.aquaone.com.au
About this Guarantee
The Manufacturer or Distributor, of Aqua One goods, is collectively known herein as “Aqua One”. Please refer to contact details for Aqua One below
or on the applicable Aqua One website. Any product that is covered by its own Guarantee (as enclosed with the product) is subject to the conditions of
that Guarantee.
Australian Guarantee
Important note: This guarantee applies in addition to the guarantees, rights and remedies conferred by the Australian Consumer Law and other
applicable Commonwealth, State and Territory legislation. The guarantee does not exclude, affect or limit those guarantees, rights or remedies, except
to the extent that their application may lawfully be excluded or limited.
In particular, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
International Guarantee
The benets given to the purchaser, under Guarantee, are in addition to all other statutory rights and remedies which the purchaser has in respect
of goods under legislation in the applicable country of purchase. This Guarantee shall not affect any such rights and should be read subject to such
legislation.
1.0. Terms and Conditions of Guarantee.
1.1. Aqua One warrants to the purchaser, for 2 years from date of original purchase, to repair or replace goods where fault is found due to defective
materials or faulty workmanship and where goods do not operate in accordance with the instructions.
1.2. All claims for repair or replacement must be made at place of purchase.
1.3. The original and dated Proof of Purchase (receipt) must be supplied with all goods claims. Please also provide this Guarantee where possible.
1.4. The Guarantee covers the Aquarium against gluing breakdown resulting in leakage.
1.5. All goods subject to claim under Guarantee should be prepared for transportation in the original packaging or other comparable packaging which
offers the same degree of protection.
1.6. Where goods are repaired or replaced under Guarantee, these goods are Guaranteed for the remainder of either the original Guarantee or
Extended Guarantee period.
1.7. Where claims on inspection reveal goods are in normal working order, Aqua One will request reimbursement of all reasonable costs incurred.
2.0. Other Terms and Conditions – Extended Guarantee
2.1. The Extended Guarantee period is for an additional 1 Year and commences on expiration of the standard guarantee period.
2.2. Application for Extended Guarantee is FREE of any registration cost to the purchaser on completion of the Extended Guarantee questionnaire
which is found on the applicable Aqua One website (refer below).
2.3. Upon receipt and acceptance of the questionnaire, Aqua One will forward (by way of email) a Certicate of Extended Guarantee to the purchaser.
2.4. For more information on how we collect, hold, use and disclose personal information provided to us, please refer to our Privacy Statement on the
Aqua One websites or write to our Privacy Ofcer, in your country of purchase.
2.5. Where Aqua One determines goods are being used in a manner contrary to the instructions, specications or this Guarantee, Aqua One reserves
the right to terminate Extended Guarantee for such goods and will provide written notice to the purchaser.
3.0. Exclusions and Limitations
Where permitted by local law, the following exclusions and limitations apply in regard to Guarantee:
3.1. Goods claims where fault is due to, but not limited by a) misuse b) neglect c) abuse d) re or ood e) normal wear and tear f) accidental breakage
g) Acts of God h) mains voltage uctuation or supply problems i) connection to any voltage other than what is stated on the rating plate j) modication
or tampering to electrical cord or plug, k) vermin, insects or foreign object l) liquid spillage or submersion of goods not designed to sustain such use or
duress.
3.2. Where inspections reveal goods are in normal working order including where noise or vibration is consistent with normal goods operation.
3.3. Attempted repairs or modications by unauthorised persons, including but not limited to the drilling of holes in the aquarium glass by unauthorised
persons.
3.4. Where the goods factory rating plate has been removed, altered, damaged or is rendered illegible.
3.5. Where goods are not installed, operated or maintained in accordance with Aqua One’s goods instructions, specications or this Guarantee.
3.6. Replacement or repair of worn consumables or replacement of lost goods, parts or components.
3.7. Costs associated with goods transportation, removal, installation, postage or cost of insurance.
3.8. Any damage incurred whilst installing, transporting or moving the goods.
3.9. Subject to certain local statutory rights and obligations to the contrary, and this guarantee shall not affect those rights or obligations, where, to the
full extent permitted by law: 1. all express and implied warranties and conditions under statute or general law, are expressly excluded and Aqua One,
where permitted, will limit liability as follows and at Aqua One’s option to: in regard to goods either a) the replacement of goods or supply of equivalent
goods b) the repair of goods or the cost of replacing the goods or of acquiring equivalent goods OR in regard to services either c) the re-supply of
services d) the cost to re-supply services.
2. Aqua One will not be liable for any loss or damage, including consequential loss or damage either directly or indirectly, or for any incidental expenses,
of any kind, and in any way whatsoever.
The additional 1 Year Extended Guarantee applies when you REGISTER online with Aqua One. Register your Extended Guarantee at
www.aquaone.com.au
(1) Consumables include items such as replacement light tubes.
Aqua One may be contacted in:
Australia
Kong’s (Aust.) Pty. Limited
PO Box 863, Ingleburn
1890 NSW Australia
www.aquaone.com.au
12
Inspiring Excellence in Fish Care!
Loading...