Aqua Creek F-802SC2 User Manual
Scout 2
9889 Garrymore Ln
Missoula, MT 59808
888-687-3552 | +1-406-549-0769
www.aquacreek.com
Pool Lift
PART #: F-802SC2
US PATENT NUMBER: [D507,769 S]
375 LB. [170 kg] MAXIMUM WEIGHT CAPACITY
MANDATORY
LEAVE THIS MANUAL WITH LIFT OWNER
Read and follow all instructions
Lift safety can only be ensured if the lift is installed and
operated according to these instructions.
• NEVER permit children to play on or around the lift
• Do not allow children to use the lift without adult
supervision
• NEVER apply direct water pressure to the electronics
• NEVER use the lift with a dry pool
• For safety reasons, NEVER swim alone
• NEVER manually rotate the lift
ADA COMPLIANT
READ CAREFULLY
Check entire box and inside all packing materials for parts. Before beginning assembly, read the
instructions and identify parts using the fi gures and parts listed in this document.
It is critical all parts be carefully inspected by the installer prior to installation to ensure no
damage occurred in transit and a damaged part is not used. If any damage occurred in transit,
Aqua Creek Products, LLC must be notifi ed within three days of receipt of unit.
Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s
warranty and may affect the safety of the user.
Copyright © 2017 Aqua Creek Products All Rights Reserved
1
Revised 9/18/17
Scout 2 Lift
Table of Contents
PAGE DESCRIPTION PAGE DESCRIPTION
2 Scout 2 Components 11 Battery Test Cable Instructions
3 ADA Installation Guidelines 12 Proper Care of Pool & Spa Lifts
4-5 Anchor Installation: Core-Drill Retro-Fit 13 Scout 2 Parts List
6
7-9 Scout 2 Lift Assembly Instructions 15 Warranty
10 Basic Troubleshooting
Anchor Installation: Saw-Cut Retro-Fit/
New Construction
14 Seat Assembly Parts List
Scout 2 Components
1. THE SCOUT 2 LIFT MAIN ASSEMBLY
2. CONTROL ARM
3. LIFTING ARM
4. ADJUSTABLE SEAT ARM
2
3
5. FOOTREST
6. ACTUATOR
8
7. HANDSET
8. 24 V BATTERY
1
2
Copyright © 2017 Aqua Creek Products All Rights Reserved
4
6
7
5
Revised 9/18/17
Installation: ADA Guidelines
ADA REQUIREMENTS (For Commercial Applications):
The Scout 2 Lift is completely ADA Compliant when installed correctly.
The installation must meet the following requirements:
• Clear deck space dimensions (see FIGURE 1)
• Install lift a minimum of 19 inches from the pool edge
(For curved pool walls contact Aqua Creek for placement)
• Deck slope no greater than 1:48
• The seat must be submerged at least 18 inches into the water. The lift
should be installed at a location with 42-48 inches of depth (deck to pool oor)
NOTE: Other requirements may be necessary based on local code requirements. The anchor system
should be bonded according to NEC Section 680 and/or local code requirements.
71"
62"
48"
ADA
CLEAR
36"
28"
(MIN)
DECK
SPACE
18"
12"
19" (MIN)
35" (MAX)
POOL WALL
FIGURE 1
Copyright © 2017 Aqua Creek Products All Rights Reserved
DECK
WATER
3
Revised 9/18/17
Anchor Installation: Core-drill Retro-t
(Typical Concrete Pool Deck Installation)
Your deck MUST have:
• Minimum footing size: 3’ - 9” x 3’ - 9” x 10” thick.
• Minimum concrete strength: 2500 psi
• Reinforcement: #5 rebar @ 10” on center (O.C.)
TOOLS REQUIRED:
CORE DRILL MARKING PEN
3” CORE DRILL BIT AIR NOZZLE & PUMP/COMP.
1 1/2” CORE DRILL BIT HEAT GUN (OPTIONAL)
EPOXY (ANCHOR ADHESIVE)* MASKING TAPE
*Use HILTI RE-500-SD adhesive anchor or SIMPSON SET-XP
anchor adhesive or equivalant.
NOTE: Your local codes may require one or more permits. Check with your local building codes for the proper
permit requirements.
1. Mark the center of the anchor location on your deck using the guidelines on page 3. Also
mark the center for the xing anchor 7 1/2” from the center anchor.
2. Using a 3” diameter core-drill bit, drill a 3” diameter hole at the anchor location. Make sure
to keep the bit square to the deck. Drill straight down to a depth of at least 6”. Then use a 1
1/2” drill bit for the xing anchor, drilling down at least 4”
NOTE: Create a depth marker on the drill bit with black electrical tape to make sure you drill to the right depth.
If you drill through the deck you may need to use the saw-cut installation instructions.
3. Remove plug and clean out the holes with a wire brush. Insert an air nozzle to the bottom
of the hole. Use a pump or compressed air to blow out the hole. A heat-gun may be helpful
in drying out the hole.
4
continued on page 5
Copyright © 2017 Aqua Creek Products All Rights Reserved
Revised 9/18/17
Anchor Installation: Core-drill Retro-t (CONTINUED)
4. Place the anchor in the hole and ‘dry-t’ it rst to make sure the anchor will be ush and
plumb with the nished deck surface when installed. Adjust the hole as needed.
NOTE: Pool decks with pavers or thick tiles may require other anchor options. Contact Aqua Creek Products.
5. Inject epoxy adhesive into each hole starting at the bottom until the hole is 1/3 to 1/2 full.
NOTE: We recommend using masking tape around the top of the anchors so that no epoxy gets inside the anchors.
1/2" X 2"
HEX BOLT &
FLAT WASHER
FIXING ANCHOR-TAB
SCOUT MAIN ASSEMBLY
1.9" POST
1" X 4"
FIXING-
ANCHOR
FIGURE A
(AQUA CREEK OR EQUIVALENT)
1.9" X 6" ANCHOR
ANCHOR MUST BE BONDED
ACCORDING TO LOCAL
REQUIREMENTS
6. Install the anchor into the epoxy lled hole by pushing down and twisting back and
forth to evenly distribute the epoxy around the anchor. Push down until it is ush with the
nished deck surface. Clean o any excess epoxy. Adjust the anchor as needed to make
sure it is ush and plumb with the deck surface. This should be done during the adhesives’
specied ‘gel time’ (see epoxy manufacturers’ instructions).
7. Let the epoxy cure for at least 24 hours before installing the lift (or where applicable ac-
cording to the epoxy manufacturers’ instructions).
Copyright © 2017 Aqua Creek Products All Rights Reserved
Revised 9/18/17
5
Loading...