Aqua Creek F-004PPPB User Manual
Portable
9889 Garrymore Ln
Missoula, MT 59808
888-687-3552 | +1-406-549-0769
www.aquacreek.com
Pro Pool-AT
PART #: F-004PPPB-AT1
US PATENT NUMBER: [D507,769 S] [7,249,386 B2]
350 LB. [160 kg] MAXIMUM WEIGHT CAPACITY
MANDATORY
LEAVE THIS MANUAL WITH LIFT OWNER
Read and follow all instructions.
Lift safety can only be ensured if the lift is installed and
operated according to these instructions.
• NEVER permit children to play on or around the lift
• Do not allow children to use the lift without adult
supervision
• NEVER apply direct water pressure to the electronics
• Do not use the Portable Pro Pool-AT for deck-to-
waterline measurements over 11”
• NEVER operate lift without the 14 weight plates installed
• NEVER use the lift with a dry pool
• For safety reasons, NEVER swim alone
READ CAREFULLY
Check entire box and inside all packing materials for parts. Before beginning assembly, read the
instructions and identify parts using the fi gures and parts listed in this document.
It is critical all parts be carefully inspected by the installer prior to installation to ensure no damage
occurred in transit and a damaged part is not used. If any damage occurred in transit, Aqua Creek
Products, LLC must be notifi ed within three days of receipt of unit.
Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s warranty
and may affect the safety of the user.
Copyright © 2018 Aqua Creek Products All Rights Reserved
1
Revised 1/12/18
Portable Pro Pool-AT Lift
Table of Contents
PAGE DESCRIPTION PAGE DESCRIPTION
2 Portable Pro Pool-AT Components 7 Portable Pro Pool-AT Lift Parts List
3-4 Portable Pro Pool-AT Assembly Instructions 8 Portable Pro Pool-AT Cart Parts List
5 Basic Troubleshooting 9 Seat Assembly Parts List
6 Proper Care of Pool & Spa Lifts 13 Warranty
Portable Pro Pool-AT Components
1. PORTABLE PRO POOL-AT LIFT
2. LINAK BATTERY CHARGER
3. 24V LINAK BATTERY
4. VITO HANDSET REMOTE
5. SEAT BELT
6. 14 WEIGHT PLATES
1
5
6
4
3
2
Copyright © 2018 Aqua Creek Products All Rights Reserved
2
Revised 1/12/18
Portable Pro Pool-AT Assembly Instructions
1. Using a 7/16” wrench, remove the four (4) nylock nuts and at
washers that are currently holding the hood onto the platform.
TOOLS REQUIRED:
• 7/16” wrench
These were installed strictly for shipping purposes and can be thrown away. Remove the
hood and set aside.
2. Begin stacking the fourteen (14) supplied weight plates on the portable platform. To ensure
proper alignment, slide the hood over the stack every three (3) or four (4) plates. Continue
this until all fourteen (14) weight plates are in place.
3. Using a 7/16” wrench, slide the hood over the stack of weight plates and attach to the
platform using the twelve (12) supplied 1/4” nylock nuts and at washers. NOTE: Be sure to
use silicone to seal the ange before bolting together.
HOOD
WEIGHT
PLATES (14)
PLATFORM
Copyright © 2018 Aqua Creek Products All Rights Reserved
1/4" FLAT WASHER (12)
1/4" NYLOCK NUT (12)
3
Revised 1/12/18
Portable Pro Pool-AT Assembly Instructions
LOOP ON TOP
FOR EASY ACCESS
THREAD THROUGH
SLOTS AND PINCH
TOGETHER TO HOLD
TOGETHER TO HOLD
4. Attach seat belt to the seat as shown in diagram to the
right.
5. Place the battery on the charger and bring to a full charge.
6. Apply dielectric grease on the metal tabs of the battery
and the control box on the lift.
7. Mount the battery onto the control box on the lift and
snap the battery into place. Listen for a ‘click’ when the
battery is installed properly. There should be no gap
between the battery and control box. See FIGURE 1.
NOTE: To extend battery life, always store battery on the
charger when the lift is not in service.
ATTACH FULLY
CHARGED BATTERY
CONTROL BOX
4
Copyright © 2018 Aqua Creek Products All Rights Reserved
FIGURE 1
Revised 1/12/18
Loading...