Aqua Computer cuplex kryos NEXT VARIO VISION Service Manual
cuplex kryos NEXT VARIO VISION 09/2017
computeraqu
a
cuplex kryos NEXT VARIO with VISION
cuplex kryos NEXT VARIO with VISION
cuplex kryos NEXT VARIO with VISIONcuplex kryos NEXT VARIO with VISION
Operating and assembly manual
Operating and assembly manual
Operating and assembly manualOperating and assembly manual
1. Preparation
1. Preparation
1. Preparation1. Preparation
Back up your data before modifying your hardware! Disconnect your PC from
the mains power outlet. To prevent damaging the sensitive hardware components, make sure to ground your workplace and yourself to prevent electrostatic discharges.
When upgrading an existing PC setup, remove the installed heat sink from the
CPU. Refer to the instruction manual of the CPU cooler for details. Remove
thermal grease residues from the CPU surface using benzine if necessary.
Place a small drop (diameter ca. 4 mm or 0.15 inch) of thermal grease supplied with the cuplex kryos NEXT centrally on the CPU. Alternatively, you can
apply a thin layer of the thermal grease using the supplied plastic spatula.
2.1. Instructions for Socket 2066, 2011-3, 2011, AM4, TR4
2.1. Instructions for Socket 2066, 2011-3, 2011, AM4, TR4
2.1. Instructions for Socket 2066, 2011-3, 2011, AM4, TR42.1. Instructions for Socket 2066, 2011-3, 2011, AM4, TR4
Place the cuplex kryos NEXT on top of
the thermal grease covered CPU, observing the orientation as shown in the
picture. Place on spring into each recess and insert a knurled screw
through each spring into the anchor
threads of the CPU socket (only one or
two revolutions). Alternately fasten
each screw a fraction of a revolution
until all four screws are fully fastened.
© 2016-2017 Aqua Computer GmbH & Co. KG – Gelliehäuser Str. 1 – D-37130 Gleichen
cuplex kryos NEXT VARIO VISION 09/2017
computeraqu
a
2.2. Instructions for Socket 1150, 1151, 1155, 1156
2.2. Instructions for Socket 1150, 1151, 1155, 1156
2.2. Instructions for Socket 1150, 1151, 1155, 11562.2. Instructions for Socket 1150, 1151, 1155, 1156
Arrange back plate and black insulation mat below the processor socket
as shown in the picture. Slide one
plastic washer onto the outer thread of
each retention bolt and screw the bolts
through the four mounting holes of the
motherboard into the back plate. For
easy installation, the retention bolts
can be screwed in by hand or with a
hexagon socket wrench.
Place the cuplex kryos NEXT on top of
the thermal grease covered CPU, observing the orientation as shown in the
picture. Slide one of the four supplied springs onto each bolt and secure each
spring using one of the knurled head screws (only one or two revolutions). Alternately fasten each screw a fraction of a revolution until all four screws are
fully fastened.
2.3. Instructions for Socket AM3+, AM3, FM2+, FM2
2.3. Instructions for Socket AM3+, AM3, FM2+, FM2
2.3. Instructions for Socket AM3+, AM3, FM2+, FM22.3. Instructions for Socket AM3+, AM3, FM2+, FM2
Arrange back plate and black insulation mat below the processor socket
as shown in the picture. Slide one
plastic washer onto the outer thread of
each retention bolt and screw the bolts
through the four mounting holes of the
motherboard into the back plate. For
easy installation, the retention bolts
can be screwed in by hand or with a
hexagon socket wrench.
Place the cuplex kryos NEXT on top of
the thermal grease covered CPU. Slide
one of the four supplied springs onto
each bolt and secure each spring using one of the knurled head screws (only one or two revolutions). Alternately
fasten each screw a fraction of a revolution until all four screws are fully fastened.
© 2016-2017 Aqua Computer GmbH & Co. KG – Gelliehäuser Str. 1 – D-37130 Gleichen
Loading...