Page 1
R
INSTALLATION
AND
OPERATING
INSTRUCTIONS
Models: XTRM-2, XTRM-3
RADIANT CONVEYOR TOASTER
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
WARNING: Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the Installation, Operating and
Maintenance Instructions thoroughly before installing or servicing this equipment.
Initial heating of unit may generate smoke or fumes and must be done in a well ventilated area.
Overexposure to smoke or fumes may cause nausea or dizziness.
This equipment has been engineered to provide you with year-round dependable service when used
according to the instructions in this manual and standard commercial kitchen practices.
UNIT MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES
INTENDED FOR OTHER THAN HOUSEHOLD USE
RETAIN THIS MANUAL FOR FUTURE REFERENCE
!!
!!
Phone: +1 (214) 421-7366
Fax: +1 (214) 565-0976
Toll Free: +1 (800) 527-2100
Website: www.apwwyott.com
E-mail: info@apwwyott.com
1
P/N 93000077 9/06
APW WYOTT
729 Third Avenue
Dallas, TX 75226
Page 2
Notes:
IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual for the life of the equipment. For
Warranty Service and/or Parts, this information is required.
Model Number Serial Number Date Purchased
SAFETY PRECAUTIONS
Before installing and operating this equipment be sure everyone involved in its operation are fully trained
and are aware of all precautions. Accidents and problems can result by a failure to follow fundamental rules
and precautions.
The following words and symbols, found in this manual, alert you to hazards to the operator, service
personnel or the equipment. The words are defined as follows:
DANGER: This symbol warns of imminent hazard which will result in serious injury or death.
!
APW Wyott takes pride in the design and quality of our products. When used as intended and with proper
care and maintenance, you will experience years of reliable operation from this equipment. To ensure best
results, it is important that you read and follow the instructions in this manual carefully.
Installation and start-up should be performed by a qualified installer who thoroughly read, understands and
follows these instruction.
If you have questions concerning the installation, operation, maintenance or service of this product, contact
APW Wyott Foodservice Equipment Company’s “ Technical Service Department”.
WARNING: This symbol refers to a potential hazard or unsafe practice, which could result in
!
serious injury or death.
CAUTION: This symbol refers to a potential hazard or unsafe practice, which may result in minor or
moderate injury or product or property damage.
!
NOTICE: This symbol refers to information that needs special attention or must be fully understood
even though not dangerous.
!
!
!
!
!
2
Page 3
TABLE OF CONTENTS
SECTION ITEM PAGE
1 Important Safety Instructions 3
2 General Information 4
3 Installation Instructions 5
4 Operation Instructions 5
5 Cleaning Instructions 6
6 Specifications 6
7 Wiring Diagram 7
8 Parts Lists with Exploded Views 8
XTRM-2 8
XTRM-3 10
9 Warranty 12
1. IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT: Read the following important safety instructions to avoid personal injury or
!
!
death, and to avoid damage to the equipment or property.
WARNING: APW Wyott toasters are designed, built, and sold for commercial use. If positioned
where the general public can usethem, make sure that all cautions, warnings, and operating
instructions are clearly posted near each unit to insureproper operation, reduce the chance of
personal injury and/or equipment damage.
!
!
WARNING: Plug unit into a properly grounded electrical outlet of the correct voltage, size and plug
configuration. If the plug and receptacle do not match, contact a qualified electrician to determine
!
the proper voltage and size and install the proper electrical outlet.
WARNING: Unit is not waterproof. DO NOT submerge in water. Do not operate if it has been
!
!
!
!
!
!
submerged in water. Do not clean the unit with a water jet.
WARNING: To avoid any injury, turn the power switch off at the fuse disconnect switch/circuit
breaker or unplug the unit from the power source and allow to cool completely before performing
any maintenance or cleaning.
WARNING: To avoid electrical shock, always unplug the unit before performing cleaning or
maintenance.
WARNING: For safe and proper operation, the unit must be located a reasonable distance from
combustible walls and materials. If safe distances are not maintained, discoloration or combustion
could occur.
WARNING: To avoid electrical shock or personal injury, do not steam clean or use excessive water
on the unit.
WARNING: If service is required on this unit, contact your authorized APW Wyott Service Agent, or
contact the APW Wyott Service Department directly at (214) 421-7366 or (800) 527-2100; fax (214)
565-0976.
!
!
!
!
!
!
!
WARNING: An earthing cable must connect the appliance to all other units in the complete
installation and from there to an independent earth connection.
!
WARNING: In Europe, appliance must be connected by an earthing cable to all other units
in the complete installation and thence to an independent earth connection in compliance
!
with EN 60335-1 and/or local codes
3
!
!
Page 4
WARNING: This product has no “user” serviceable parts. To avoid damage to the unit or injury to
personnel, use only Authorized APW Wyott Service Agents and genuine APW Wyott Parts when
!
service is required..
WARNING: Genuine APW Wyott Replacement Parts are specified to operate safely in the
environments in which they are used. Some aftermarket or generic replacement parts do not have
the characteristics that will allow them to operate safely in APW Wyott equipment. It is essential to
!
!
!
!
!
use APW Wyott Replacement Parts when repairing APW Wyott equipment. Failure to use APW
Wyott Replacement Parts may subject operators of the equipment to hazardous electrical voltage,
resulting in electrical shock or burn.
CAUTION: Some exterior surfaces on the unit will get hot. Use caution when touching these areas
to avoid injury.
CAUTION: Locate the unit at the proper counter height, in an area that is convenient for use. The
location should be level to prevent the unit or it’s contents from accidentally falling, and strong
enough to support the weight of the unit and food.
CAUTION: Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish of your unit,
marring it’s appearance and making it susceptible to dirt accumulation.
WARNING: Failure to provide clearances will cause unit failure and invalidate warranty claims
(see installation instructions).
!
!
!
!
!
!
NOTICE: Do not use toppings (butter, etc.) on product as product is inverted during normal
operation.
!
NOTICE: Operating toaster without legs invalidates any warranty claims.
!
NOTICE: Neglecting to keep fan opening clean could result in toaster failure.
!
!
!
!
2. GENERAL INFORMATION
XTRM-2: 1.
19.658”D (49.931cm)
XTRM-3: 1. Overall Dimensions w/Wire Feeder - 15.033”H (38.183cm) x 19.191”W (48.745cm) x
Overall Dimensions w/Wire Feeder - 15.033”H (38.183cm) x 16.191”W (41.125cm) x
2. Product Opening - 1.50”H
3. Electrical Requirements (Single phase):
A. 208 Volt, 2840 Watt, 13.7 Amp.
B. 230/240 Volt, 2840 Watt, 11.9 Amp.
C. Cordset configuration
1. Each toaster equipped with three wire grounded cordset and standard 3 prong plug.
4. Net/Shipping Weight – 49
19.658”D (49.931cm)
2. Product Opening - 1.50”H
3. Electrical Requirements (Single phase):
A. 208 Volt, 3340 Watt, 16.1 Amp.
B. 230/240 Volt, 3340 Watt, 14.0 Amp.
C. Cordset configuration
1. Each toaster equipped with three wire grounded cordset and standard 3 prong plug.
4. Net/Shipping Weight –
(3.810cm) x 10.50”W (26.67cm)
lb.(22.26kg) / 46lb.(20.865kg)
(3.810cm) x 13.50”W (34.29cm)
50 lb.(22.8kg) / 47 lb.(21.319kg)
4
Page 5
3. INSTALLATION INSTRUCTIONS
I. Check Contents: Refer to Figure 1, account for the following parts:
A. Remove foam pad and slide reflector tray in with
wire feeder in upright position as shown.
B. Ensure tray is properly engaged in tray slides. To do this
simply hold the front of the tray higher than the rear as
the back of the tray must slide under the slide on
either side, You will know if done correctly because
tray will be secure. No rocking or teetering will take place.
C. Toast Drawer - shipped in place
D. Instruction Manual - shipped loose
!
2. Toaster Placement:
WARNING: Operating toaster without Reflector Tray reduces toasting capabilities.
A. Locate toaster near a grounded receptacle of the proper configuration (see below). Plug
the cordset directly into receptacle (DO NOT USE AN EXTENSION CORD).
1. In the U.S.: 208, 230/240V uses NEMA 6-20R.
B. Place toaster on flat surface providing following minimum clearances:
1. Base = one inch (provided with legs installed).
2. Side and back walls = two inches
3. Overhead = Enough space to allow adequate heat displacement.
C. Position toaster where customers will not contact any surface labeled “CAUTION HOT”.
C
Figure 1
A
B
!
1. Preparation
A. Clean toaster thoroughly before first use (See cleaning instructions).
B. Controls Familiarity
1. Main Power Switch (located on very bottom of control panel): There are two rocker
switches. The bottom switch powers the unit “ON”. It also turns on the bottom element.
The top switch is a standby switch that runs the top element. When the standby switch is
in the “ON” position the unit is at full power. When the standby switch is in the “OFF”
position the unit is running at 50%.
a) Full Power: Flip both rocker switches to the right.
b) Power Off: Flip both rocker switches to the left.
c) Warm-up time: Allow five (5) minutes.
2. Normal Use
A. Loading Product
1. Place product on Wire Feeder. The conveyor will automatically draw product through
the toaster at a speed determined by conveyor speed control.
2. Conveyor Speed Control: Set knob to the three (3) position for warm-up.
3. Thermostat Controls:
A. The top thermostat runs the top element & the bottom thermostat runs the bottom element.
B. Toasting Darkness: determined by conveyor speed & thermostat control.
1. Darkest toasting - set conveyor speed control to far left setting & thermostat controls to
highest setting.
2. Lightest toasting - set conveyor speed control to far right setting.
3. Other factors affecting toasting darkness.
4. OPERATION INSTRUCTIONS
5
Page 6
1. Daily Cleaning
A. With toaster off and cool, turn toaster on and set conveyor speed to four.
B. Using a plastic abrasive pad, wipe the conveyor belt in a back and forth motion (side-to side)
motion to remove baked-on product. Wipe the conveyor belt in the same manner with a hot,
damp cloth.
C. Turn off toaster.
D. Slide the reflector/crumb tray out of toaster by pulling forward. Dispose of crumbs and wash
tray in hot, soapy water. Dry tray and place back in toaster.
E. Remove toast drawer from toaster by sliding out and lifting up. Dispose of crumbs and wash
drawer in hot, soapy water. Wipe crumbs from inside the toaster with a hot, damp cloth. Dry
drawer and place back in toaster.
F. Wipe the exterior surfaces of the toaster with a hot, damp cloth.
a) Product moistness - moister product requires slower speeds
b) Sugar content in product - product with more sugar requires slower speeds
c) Product Temperature - cooler product requires slower speeds
4. For best results, use day old bread stored room temperature.
5. CLEANING INSTRUCTIONS
6. SPECIFICATIONS
19.482
(495mm)
CAUTION HOT
16.254
(413mm)
XTRM-2
50°
4.493
(114mm)
2.709
69mm
20.510
520.95mm
13.323
(338mm)
13.967
(355mm)
(380mm)
14.967
2.820 (72mm)
6.654
(169mm)
6
Page 7
19.420
(493mm)
19.254
(489mm)
13.967
(355mm)
XTRM-3
s e
m i i w
50°
4.493
(114mm)
2.820 (72mm)
tr
c VeI o
2.647
(67mm)
20.782
(527.86mm)
Rear Fan
Control Fan
Motor
Existing Wire
BLACK
11
16.323
(415mm)
L1
G
BLACK
BLUE
BLUE
L2
14.967
(380mm)
7. WIRING DIAGRAM
Top Element
16
Bottom Element
16
11
11
2
16
4
1
7
L1
11
L2
L2
5
5
L1
L2
Terminal
Block
6.654
(169mm)
8
12
13
14
7
7
Rheostat
BLACK
8
14
2
66
2
6
BLUE
Top
EGO
12
4
Bottom
EGO
1
1
5
4
5
Top
EGO
L2
12
H1
Pilot
P2
4
EGO
L2
H1
14
Pilot
P2
L1
Top
Switch
L2
2
L1
Bottom
Switch
L2
6
8
10
8
H2
L1
P1
Top
H2
L1
P1
5
9
10 10
3
3
15
9
13
9
3
3
15
3
1
7
10
7
Page 8
6
47
5
3
15
9
57
29
8
28
55
10
12
30
8. PARTS LISTS & EXPLODED VIEWS
XTRM-2 EXPLODED VIEW
53
60
39
37
38
56
48
7
13
34
35
11
1
19
20
59
58
17
40
16
33
27
23
43
22
24
25
26
2
4
14
51
44
64
46
42
49
50
41
62
36
63
61
21
32
52
31
8
Page 9
ITEM PART NUMBER DESCRIPTION (XTRM-2 PARTS LIST) QUANTITY
1
1
1
1
1
2
1
2
2
1
2
1
2
4
2
1
1
1
1
4
4
1
1
2
1
2
2
1
2
1
1
1
1
1
1
2
10
4
10
14
2
1
1
1
1
2
1
9
12
1
1
1
1
9
2
2
1
1
2
2
1
8
2
2
2
2
8
1
1
1
10
11
12
13
14
15
16
17
18*
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45*
46
47
48
49
50
51
52
53
54*
55
56
57
58
59
60
61
62
63
64
65*
66*
67*
1
2
3
4
5
6
7
8
9
93000040
93000158
93000159
93000116
93000115
93000225
93030181
38130
38125
38122
83248
83956
83868
83267
93000226
85149
85144
89184
85284
89076
89030
83261
93200061
70444800
93200066
69104-EGO
69103-EGO
83333
88705
93000206
93100065
93100197
93000233
93000302
75617
83821
89061
93000194
89073
88889
81600087
89111
83277
89145
93200064
89054
85287
89063
94000114
93200084
85281
93000196
85282
88940
93000232
89039
93200303
58081
93000230
93000231
93000199
93000229
93000227
93000186
54093
54094
88951
89056
69154
89182
XTRM 2, RIVIET ASSEMBLY
XTRM-2&3 CONTROL PANEL EXTRUSION
EXTRUSION, XTRM 2&3
XTRM-2&3, PANEL, LEFT OUTER
XTRM-2&3, PANEL, RIGHT SIDE
END CAP, F/L & B/R
COVER, TOP, XTRM 2
ASSY, CLIP BEARING
BEARING FLANGED POLYMER
W'ASSY IDLER SHAFT
BEARING, SHAFT
DRIVE SHAFT ASSY AT-10 SEGMENTED BELT
SPACER, CONVEYOR SHAFT
LEG 1" PLASTIC W/CHROME
END CAP, B/L & F/R
MOTOR, AT'S 208/240V 60HZ VARIABLE
MOTOR, AT'S 230V 60HZ VARIABLE
BUSHING, .875 HEYCO 2126
FAN, COOLING 4.5" 105CFM 208/230V
WASHER, LOCK 1/4 INTERNAL
SCREW, 10-32X3/4
SPROCKET, 12 TOOTH 1/4 PITCH 3/8 BORE
ASSY, PLATE, CONTROLS
SWITCH, ROCKER ON-OFF
PLATE, SPACE, CONTROLS
INFINITE SWITCH-EGO (208V)
INFINITE SWITCH-EGO (230/240V)
RHEOSTAT 208/240 V. PIGGY-BACK TERM
KNOB 039-266 8A BLACK
BELT, WIRE 27x.05 3 SEG.
ASSY, XTRM 2 FEEDER
DRAWER TOAST
SPROCKET, 32 TOOTH 1/4 PITCH
CHAIN, 1/4" DRIVE 67 PITCH
KNOB W/NO'S. 0 TO 9
BRACKET, BEARING
NUT, HEX 10-24
XTRM 2&3, SMALL ELEMENT COVER
SCREW, #8 X 1/2 HEX TAPIT SHT MTL TYPE AB
SCREW #8 X 1/2 AB SMS PHL TRUSS LGM NI PLT
SCREW, 8-32 x 3/8, PHILLIPS, PAN HEAD
BUSHING, STRAIN RELIEF SR-7W-2
CORDSET, ASSY 208/240V (CORD 85640)
TERMINAL BLOCK 300V-30AMPS
LABEL, XTRM CONTROL
NUT, KEPS 6-32
FAN GUARD
NUT, HEX 8-32
SCREW, COUNTERSINK, 6-32X5/16,Z,BLK
XTRM-3, INSULATION CENTER PANEL
FAN,COOLING,3" DIA, 208/230V
XTRM-2 & 3 AIR DEFLECTOR
Guard, 3.15 Sq. Fan
WASHER, 1-1/2 RD
XTRM-2&3, RIGHT SIDE INSULATION
SCREW, 8-32X5/16 PH PAN SS
LABEL, SPEED GUIDCAUTION HOT!
LABEL, CAUTION HOT!
XTRM-2&3, RIGHT EXTRUSION INSULATION
XTRM-2&3, LEFT EXTRUSION INSULATION
XTRM 2, BACK COVER
HEX MACHINE SCREW, #6-32 X 3/4
XTRM-2&3, CONTROL BOX INSULATION
XTRM-2, ELEMENT RACK
ELEMENT, 208V-1400W
ELEMENT, 230/240V-1400W
SCREW, 8-32x2" PHILLIPS PAN MS SS
WASHER #8 INTERNAL LOCK, SS
THERMOSTAT, THERM-O-DISC W/MOUNT CLIP
BUSHING, .5 HEYCO 2058
*NOT SHOWN
9
Page 10
15
6
3
59
48
5
40
30
9
29
8
56
31
XTRM-3 EXPLODED VIEW
38
54
39
57
7
13
36
35
11
1
17
19
20
16
34
28
23
44
22
24
25
26
2
4
14
52
1
64
47
60
43
50
51
41
42
27
58
37
63
21
33
53
32
10
Page 11
ITEM PART NUMBER DESCRIPTION (XTRM-3 PARTS LIST) QUANTITY
10*
11
12*
13
14
15
16
17
18*
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45*
46*
47
48
49*
50
51
52
53
54
55*
56
57
58
59
60
61*
62*
63
64
65*
66*
67*
1
2
3
4
5
6
7
8
9
93200040
93000158
93000159
93000116
93000115
93000225
93230047
38130
38125
93200070
83248
83976
83868
83267
93000226
85149
85144
89184
85284
89076
89030
83261
93200061
70444800
93200066
69104-EGO
69103-EGO
83333
93200036
88705
83880
93200052
93200048
93000233
82902
75617
83821
89061
93000194
89073
88889
81600087
89111
83277
89145
93200064
89054
85287
89063
94000114
93200084
85281
93000196
85282
88940
93000232
89039
93200303
58081
54021
54032
93000230
93000231
93200199
93000229
93000227
88951
89056
69154
89182
XTRM 3, RIVIET ASSEMBLY
XTRM-2&3 CONTROL PANEL EXTRUSION
EXTRUSION, XTRM 2&3
XTRM-2&3, PANEL, LEFT OUTER
XTRM-2&3, PANEL, RIGHT SIDE
END CAP, F/L & B/R
COVER, TOP, XTRM 3
ASSY, CLIP BEARING
BEARING FLANGED POLYMER
SHAFT, IDLER XTRM
BEARING, SHAFT
ASSEMBLY, DRIVE SHAFT
SPACER, CONVEYOR SHAFT
LEG 1" PLASTIC W/CHROME
END CAP, B/L & F/R
MOTOR, AT'S 208/240V 60HZ VARIABLE
MOTOR, AT'S 230V 60HZ VARIABLE
BUSHING, .875 HEYCO 2126
FAN, COOLING 4.5" 105CFM 208/230V
WASHER, LOCK 1/4 INTERNAL
SCREW, 10-32X3/4
SPROCKET, 12 TOOTH 1/4 PITCH 3/8 BORE
ASSY, PLATE, CONTROLS
SWITCH, ROCKER ON-OFF
PLATE, SPACE, CONTROLS
INFINITE SWITCH-EGO (208V)
INFINITE SWITCH-EGO (230/240V)
RHEOSTAT 208/240 V. PIGGY-BACK TERM
XTRM 3, ELEMENT RACK
KNOB 039-266 8A BLACK
CONVEYOR BELT 79 LINKS
ASSY, XTRM 3 FEEDER
XTRM-3, TOASTER DRAWER
SPROCKET, 32 TOOTH 1/4 PITCH
CHAIN, 1/4" DRIVE 67 PITCH
KNOB W/NO'S. 0 TO 9
BRACKET, BEARING
NUT, HEX 10-24
XTRM 2&3, SMALL ELEMENT COVER
SCREW, #8 X 1/2 HEX TAPIT SHT MTL TYPE AB
SCREW #8 X 1/2 AB SMS PHL TRUSS LGM NI PLT
SCREW, 8-32 x 3/8, PHILLIPS, PAN HEAD
BUSHING, STRAIN RELIEF SR-7W-2
CORDSET, ASSY 208/240V (CORD 85640)
TERMINAL BLOCK 300V-30AMPS
LABEL, XTRM CONTROL
NUT, KEPS 6-32
FAN GUARD
NUT, HEX 8-32
SCREW, COUNTERSINK, 6-32X5/16,Z,BLK
XTRM-3, INSULATION CENTER PANEL
FAN,COOLING,3" DIA, 208/230V
XTRM-2 & 3 AIR DEFLECTOR
Guard, 3.15 Sq. Fan
WASHER, 1-1/2 RD
XTRM-2&3, RIGHT SIDE INSULATION
SCREW, 8-32X5/16 PH PAN SS
LABEL, SPEED GUIDCAUTION HOT!
LABEL, CAUTION HOT!
ELEMENT, 208V-1650W
ELEMENT, 230/240V-1650W
XTRM-2&3, RIGHT EXTRUSION INSULATION
XTRM-2&3, LEFT EXTRUSION INSULATION
XTRM 3, BACK COVER
HEX MACHINE SCREW, #6-32 X 3/4
XTRM-2&3, CONTROL BOX INSULATION
SCREW, 8-32x2" PHILLIPS PAN MS SS
WASHER #8 INTERNAL LOCK, SS
THERMOSTAT, THERM-O-DISC W/MOUNT CLIP
BUSHING, .5 HEYCO 2058
1
1
1
1
1
2
1
2
2
1
2
1
2
4
2
1
1
1
1
4
4
1
1
2
1
2
2
1
2
2
1
1
1
1
1
1
2
10
4
10
14
2
1
1
1
1
2
1
9
12
1
1
1
1
9
2
2
1
1
2
2
2
2
1
8
2
8
1
1
1
*NOT SHOWN
11
Page 12
9. APW WYOTT EQUIPMENT LIMITED WARRANTY
APW Wyott Foodservice Equipment Company warrants it's equipment against defects in materials and workmanship, subject to the
following conditions:
This warranty applies to the original owner only and is not assignable.
Should any product fail to function in its intended manner under normal use within the limits defined in this warranty, at the option of
APW Wyott such product will be repaired or replaced by APW Wyott or its Authorized Service Agency. APW Wyott will only be
responsible for charges incurred or service performed by its Authorized Service Agencies. The use of other than APW Wyott
Authorized Service Agencies will void this warranty and APW Wyott will not be responsible for such work or any charges associated
with same. The closest APW Wyott Authorized Service Agent must be used.
This warranty covers products shipped into the 48 contiguous United States, Hawaii, metropolitan areas of Alaska and Canada. There
will be no labor coverage for equipment located on any island not connected by roadway to the mainland.
Warranty coverage on products used outside the 48 contiguous United States, Hawaii, and metropolitan areas of Alaska and Canada
may vary. Contact the international APW Wyott distributor, dealer, or service agency for details.
Time Period
One year for parts and one year for labor, effective from the date of purchase by the original owner. The Authorized Service Agency
may, at their option, require proof of purchase. Parts replaced under this warranty are warranted for the un-expired portion of the
original product warranty only.
Exceptions
In all cases, parts covered by extended warranty will be shipped FOB the factory after the first year.
Portable Carry In Products
Equipment weighing over 70 pounds or permanently installed will be serviced on-site as per the terms of this warranty. Equipment
weighing 70 pounds or under, and which is not permanently installed, i.e. with cord and plug, is considered portable and is subject to
the following warranty handling limitations. If portable equipment fails to operate in its intended manner on the first day of
connection, or use, at APW Wyott's option or its Authorized Service Agency, it will be serviced on site or replaced.
From day two through the conclusion of this warranty period, portable units must be taken to or sent prepaid to the APW Wyott
Authorized Service Agency for in-warranty repairs. No mileage or travel charges are allowed on portable units after the first day of use.
If the customer wants on-site service, they may receive same by paying the travel and mileage charges. Exceptions to this rule: (1)
countertop warmers and cookers, which are covered under the Enhanced Warranty Program, and (2) toasters or rollergrills which have
in store service.
Exclusions
The following conditions are not covered by warranty:
If the equipment has been changed, altered, modified or repaired by other than an Authorized Service Agency during or after the
warranty period, then the manufacturer shall not be liable for any damages to any person or to any property, which may result from the
use of the equipment thereafter.
This warranty does not cover services performed at overtime or premium labor rates. Should service be required at times which
normally involve overtime or premium labor rates, the owner shall be charged for the difference between normal service rates and such
premium rates. APW Wyott does not assume any liability for extended delays in replacing or repairing any items beyond its control.
In all cases, the use of other than APW Wyott Authorized OEM Replacement Parts will void this warranty.
This equipment is intended for commercial use only. Warranty is void if equipment is installed in other than commercial application.
Water Quality Requirements
Water supply intended for a unit that has in excess of 3.0 grains of hardness per gallon (GPG) must be treated or softened before
being used. Water containing over 3.0 GPG will decrease the efficiency and reduce the operation life of the unit.
Note: Product failure caused by liming or sediment buildup is not covered under warranty.
“THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSES
AND CONSTITUTES THE ENTIRE LIABILITY OF APW WYOTT. IN NO EVENT DOES THE LIMITED WARRANTY
EXTEND BEYOND THE TERMS STATED HEREIN.”
*Gas/Electric Cookline: Models GCB, GCRB, GF, GGM, GGT, CHP-H, EF, EG, EHP. Three (3) Year Warranty on all
component parts, except switches and thermostats. (2 additional years on parts only. No labor on second or third year.)
*Broiler Briquettes,
*Heat Strips: Models FD, FDL, FDD, FDDL. Two (2) Year Warranty on element only. No labor second year.
*Glass Windows, Doors, Seals, Rubber Seals, Light Bulbs:
*Equipment failure relating to improper installation, improper utility connection or supply and problems due to
ventilation.
*Equipment that has not been properly maintained, calibration of controls, adjustments, damage from improper cleaning
and water damage to controls.
*Equipment that has not been used in an appropriate manner, or has been subject to misuse or misapplication, neglect,
abuse, accident, alteration, negligence, damage during transit, delivery or installation, fire, flood, riot or act of god.
*Equipment that has the model number or serial number removed or altered.
Rock Grates, Cooking Grates, Burner Shields, Fireboxes: 90 Day Material Only. No Labor.
90 Day Material Only. No Labor.
9/05
12
Loading...