APW Wyott XTRM-2 3 INCH Operators Manual

Download

Page 1

INSTALLATION

AND

OPERATING

INSTRUCTIONS

Models: XTRM-2 3”, XTRM-3 3”

RADIANT CONVEYOR TOASTER

INTENDED FOR OTHER THAN HOUSEHOLD USE

RETAIN THIS MANUAL FOR FUTURE REFERENCE

UNIT MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the Installation, Operating and Maintenance Instructions thoroughly before installing or servicing this equipment.

Initial heating of unit may generate smoke or fumes and must be done in a well ventilated area. Overexposure to smoke or fumes may cause nausea or dizziness.

This equipment has been engineered to provide you with year-round dependable service when used according to the instructions in this manual and standard commercial kitchen practices.

P/N 93030077 9/06

Phone: +1 Fax: +1 (214) 565-0976 Toll Free: +1 (800) 527-2100 Website: www.apwwyott.com E-mail: info@apwwyott.com

(214) 421-7366

APW WYOTT

729 Third Avenue

Dallas, TX 75226

Page 2

Notes:

IMPORTANT FOR FUTURE REFERENCE

Please complete this information and retain this manual for the life of the equipment. For Warranty Service and/or Parts, this information is required.

Model Number Serial Number Date Purchased

1. SAFETY PRECAUTIONS

Before installing and operating this equipment be sure everyone involved in its operation are fully trained and are aware of all precautions. Accidents and problems can result by a failure to follow fundamental rules and precautions.

The following words and symbols, found in this manual, alert you to hazards to the operator, service personnel or the equipment. The words are defined as follows:

DANGER: This symbol warns of imminent hazard whichwill result in serious injury or death.

WARNING: This symbol refers to a potential hazard or unsafe practice, which could result in

serious injury or death.

CAUTION: This symbol refers to apotential hazard or unsafe practice, which may result in minor or moderate injury or product or property damage.

NOTICE: This symbol refers to information that needs specialattention or must be fully understood

even though not dangerous.

APW Wyott

care and maintenance, you will experience years of reliable operation from this equipment. To ensure best results, it is important that youread and follow the instructions in this manual carefully.

Installation and start-up should be performed by a qualified installer who thoroughly read, understands and follows these instruction. If you have questions concerning the installation, operation, maintenance or service of this product, contact APW Wyott Foodservice Equipment Company’s “

takes pride in the design and quality of our products. When used as intended and with proper

Technical Service Department”.

Page 3

TABLE OF CONTENTS

SECTION ITEM PAGE

1 2

2 3

3 4

4 5

5 5

6 6

7 6

8 7

9 8

10 12

Safety Precautions

Important Safety Instructions

General Information

Installation Instructions

Operation Instructions

Cleaning Instructions

Specifications

Wiring Diagram

Parts Lists with Exploded Views

XTRM-2 3” 8 XTRM-3 3” 10

Warranty

2. IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT: Read the following important safety instructions to avoid personal injury or

death, and to avoid damage to the equipmentor property.

WARNING: APW Wyott toasters are designed, built, and sold for commercial use. If positioned

where the general public can usethem, make sure that all cautions, warnings, and operating

instructions are clearly posted near each unit to insureproper operation, reduce the chance of personal injury and/or equipment damage.

WARNING: Plug unit into a properly grounded electrical outlet of the correct voltage, size and plug

configuration. If the plug and receptacle do not match, contact a qualified electrician to determine

the proper voltage andsize and install the properelectrical outlet.

WARNING: In Europe, appliance must be connected by an earthing cable to all other units

in the complete installation and thence to an independent earth connection in compliance

with EN 60335-1 and/or local codes

WARNING: Unit is not waterproof. Do not submerge in water. Do not operate if it has been

submerged in water. Do not clean the unit with a water jet.

WARNING: To avoid any injury, turn the power switch off at the fuse disconnect switch/circuit breaker or unplug the unit from the power source and allow to cool completely before performing

any maintenance or cleaning.

WARNING: To avoid electrical shock, always unplug the unit before performing cleaning or maintenance.

WARNING: An earthing cable must connect the appliance to all other units in the complete

installation and from thereto an independent earth connection.

WARNING: For safe and proper operation, the unit must be located a reasonable distance from

combustible walls and materials. If safe distances are not maintained, discoloration or combustion

could occur.

WARNING: To avoid electrical shock or personal injury, do not steam clean or use excessive water on the unit.

WARNING: If service is required on this unit, contact your authorized APW Wyott Service Agent, or

contact the APW Wyott Service Department directly at (214) 421-7366 or (800) 527-2100; fax (214)

565-0976.

Page 4

WARNING: This product has no “user” serviceable parts. To avoid damage to the unit or injury to

personnel, use only Authorized APW Wyott Service Agents and genuine APW Wyott Parts when

service is required..

WARNING: Genuine APW Wyott Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in APW Wyott equipment. It is essential to

use APW Wyott Replacement Parts when repairing APW Wyott equipment. Failure to use APW Wyott Replacement Parts may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn.

CAUTION: Some exterior surfaces on the unit will get hot. Use caution when touching these areas

to avoid injury.

CAUTION: Locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or it’s contents from accidentally falling, and strong

enough to support the weight of the unitand food.

CAUTION: Use only non-abrasive cleaners.Abrasive cleaners could scratch the finish of your unit,

marring it’s appearance andmaking it susceptible to dirt accumulation.

WARNING: Failure to provide clearances will cause unit failure and invalidate warranty claims (see installation instructions).

NOTICE:Do not use toppings (butter, etc.) on product as product is inverted during normal

operation.

NOTICE: Operating toaster without legs invalidates any warrantyclaims.

NOTICE: Neglecting to keep fan opening clean could result in toaster failure.

XTRM-2 3”:1.

2. Product Opening - 3.0”H

3. Electrical Requirements (Single phase):

4. Net/Shipping Weight – 51

XTRM-3 3”

: 1. Overall Dimensions w/Wire Feeder - 16.067”H (408cm) x 19.254”W (489cm) x

2. Product Opening - 3.0”H

3. Electrical Requirements (Single phase):

4. Net/Shipping Weight –

3. GENERAL INFORMATION

Overall Dimensions w/Wire Feeder - 16.067”H (408cm) x 16.254”W (41.13cm) x

20.511”D (521cm) (7.62cm) x 10.50”W (26.67cm)

A. 208 Volt,2840 Watt, 13.7 Amp. B. 230/240 Volt,2840 Watt, 11.9Amp. C. Cordset configuration

1. Each toaster equipped with three wire grounded cordset and standard 3 prong plug.

lb.(23.15kg) / 46lb.(20.865kg)

20.511”D (521cm) (7.62cm) x 13.50”W (34.29cm)

A. 208 Volt,3340 Watt, 16.1 Amp. B. 230/240 Volt,3340 Watt, 14.0 Amp. C. Cordset configuration

1. Each toaster equipped with three wire grounded cordset and standard 3 prong plug.

50 lb.(22.8kg) / 47 lb.(21.319kg)

Page 5

4. INSTALLATION INSTRUCTIONS

I. Check Contents:

A. Remove foam pad and slide reflector tray in with

wire feeder in upright position as shown.

B. Ensure tray is properly engaged in tray slides. To do this

simply hold the front of the tray higher than the rear as the back of the tray must slide under the slide on either side, You will know if done correctly because

tray will be secure. No rocking or teetering will take place. C. Toast Drawer - shipped in place D. Instruction Manual - shipped loose

2. Toaster Placement:

A. Locate toaster near a grounded receptacle of the proper configuration (see below). Plug

the cordset directly into receptacle (DO NOT USEAN EXTENSION CORD).

B. Place toaster on flat surface providing following minimum clearances:

C. Position toaster where customers will not contact any surface labeled “CAUTION HOT”.

Refer to Figure 1, account for the following parts:

WARNING: Operating toaster without Reflector Tray reduces toasting capabilities.

1. In the U.S.: 208, 230/240V uses NEMA 6-20R.

1. Base = one inch (provided with legs installed).

2. Side and back walls = two inches

3. Overhead = Enough space to allow adequate heat displacement.

Figure 1

1. Preparation

A. Clean toaster thoroughly before first use (See cleaning instructions). B. Controls Familiarity

1. Main Power Switch (located on very bottom of control panel): There are two rocker switches. The bottom switch powers the unit “ON”. It also turns on the bottom element.

The top switch is a standby switch that runsthe top element.When the standby switch is in the “ON” position the unit is at full power. When the standby switch is in the “OFF”

position the unit is running at 50%.

a) Full Power: Flip both rocker switches to the right. b) Power Off: Flip both rocker switches to the left. c) Warm-up time: Allow five (5) minutes.

2. Normal Use

A. Loading Product

1. Place product on Wire Feeder. The conveyor will automatically draw product through

the toaster at a speed determined by conveyor speed control.

2. Conveyor SpeedControl: Set knob to the three (3) position for warm-up.

3. Thermostat Controls:

A. The top thermostat runs thetop element & the bottom thermostat runs thebottom element.

B. Toasting Darkness: determined by conveyor speed & thermostat control.

1. Darkest toasting - set conveyor speed control to far left setting & thermostat controls to

highest setting.

2. Lightest toasting - set conveyor speed control to far right setting.

3. Other factors affecting toasting darkness.

5. OPERATION INSTRUCTIONS

Page 6

1. Daily Cleaning

A. With toaster off and cool, turn toaster on and set conveyorspeed to four. B. Using a plastic abrasive pad, wipe the conveyor belt in a back and forth motion (side-to side)

motion to remove baked-on product. Wipe the conveyor belt in the same manner with a hot,

damp cloth. C. Turn off toaster. D. Slide the reflector/crumb tray out of toaster by pulling forward. Dispose of crumbs and wash

tray in hot, soapy water.Dry tray and place back in toaster. E. Remove toast drawer from toaster by sliding out and lifting up. Dispose of crumbs and wash

drawer in hot, soapy water. Wipe crumbs from inside the toaster with a hot, damp cloth. Dry

drawer and place back in toaster.

F. Wipe the exterior surfaces of the toaster with a hot, damp cloth.

a) Product moistness - moister product requires slower speeds b) Sugar content in product - product with more sugar requires slower speeds c) Product Temperature- cooler product requires slower speeds

4. For best results, use day old bread stored room temperature.

6. CLEANING INSTRUCTIONS

7. SPECIFICATIONS

XTRM-2 3 INCH

19.408

19.296

(490mm)

16.254

(413mm)

13.323

(338mm)

15.067

(383mm)

15.067

16.067

(408mm)

ISOMETRIC VIEW

50°

5.593

(142mm)

2.820 (72mm)

2.820

6.654

(169mm)

2.633

2.521

(64mm)

20.323

20.511

(516mm)

208V 2850W

Page 7

XTRM-3 3 INCH

19.293

(490mm)

19.254

(489mm)

16.323 (415mm)

16.775 (426mm)

ISOMETRIC VIEW

50°

5.593

15.067

(383mm)

16.067

(408mm)

(142mm)

2.820 (72mm)

6.654 (169mm)

8. WIRING DIAGRAM

2.518

(64mm)

20.655

(525mm)

Rear Fan

Control Fan

Motor

Existing Wire

BLACK

BLUE

Top Element

Bottom Element

BLUE

Terminal

Block

BLACK

BLUE

EGO

Bottom

EGO

To p

Rheostat

Top

EGO

Pilot

EGO

Top

Pilot

Top

Switch

10 10

Bottom Switch

Page 8

9. PARTS LISTS & EXPLODED VIEWS

XTRM-2 3 INCH - EXPLODED VIEW

Page 9

XTRM-2 3” PARTS LIST

ITEM P/N DESCRIPTION QUAN

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

18* 19*

20 21 22 23 24 25 26

27 28 29 30 31 32 33

93030040

93030158 93030159 93030116 93030115 93000225

93030181 93030199

38130 38125 38122 83248 83956 83868 83267

93000226

85149 85144 89184 85284 89076 89030

83261 93230061 70444800

93200066

69104-EGO 69103-EGO

83333 93000186

88705

82920 93100065 93100197 93000233

XTRM-2 3", RIVIET ASSEMBLY XTRM-2 3"-CONTROL PANEL EXTRUSION EXTRUSION, XTRM 2 3" XTRM-2 3", PANEL, LEFT OUTER XTRM-2 3", PANEL, RIGHT SIDE END CAP, F/L & B/R COVER, TOP, XTRM 2 XTRM-2 3", BACK COVER ASSY, CLIP BEARING BEARING FLANGED POLYMER W'ASSY IDLER SHAFT BEARING, SHAFT DRIVE SHAFT ASSYAT-10 SEGMENTED BELT SPACER, CONVEYOR SHAFT LEG 1" PLASTIC W/CHROME END CAP, B/L & F/R MOTOR, AT'S 208/240V 60HZ VARIABLE MOTOR, AT'S 230V 60HZ VARIABLE BUSHING, .875 HEYCO 2126 FAN, COOLING 4.5" 105CFM 208/230V WASHER, LOCK 1/4 INTERNAL SCREW, 10-32X3/4 SPROCKET, 12 TOOTH 1/4 PITCH 3/8 BORE ASSY, PLATE, CONTROLS 3" XTRM SWITCH, ROCKER ON-OFF PLATE, SPACE, CONTROLS INFINITE SWITCH-EGO (208V) INFINITE SWITCH-EGO (230/240V) RHEOSTAT 208/240 V. PIGGY-BACK TERM XTRM-2, ELEMENT RACK KNOB 039-266 8A BLACK BELT, WIRE 27x.05 3 SEG. ASSY, XTRM 2 FEEDER DRAWER TOAST SPROCKET, 32 TOOTH 1/4 PITCH

ITEM P/N DESCRIPTION QUAN

1 1 1 1 1 2 1 1 2 2 1 2 1 2 4 2 1 1 1 1 4 4 1 1 2 1 2 2 1 2 2 1 1 1 1

34 35 36

37*

38 39 40 41 42 43 44 45 46 47

48*

49 50 51

52*

53 54 55 56 57 58 59 60 61 62 63 64

65* 66*

82902 75617 83821

89061 93000194

93000229

89073

88889 81600087

89111

83277

89145 93230064

89054

85287

88923

89063 94000114 93200084

85281 93000196

85282

93030227

88940 93030230 93030231 93030232

89039 93200303

58081

54093

54094

69154

89182

CHAIN, 1/4" DRIVE 67 PITCH KNOB W/NO'S. 0 TO 9 BRACKET, BEARING NUT, HEX 10-24 XTRM 2&3, SMALL ELEMENT COVER HEX MACHINE SCREW, #6-32 X 3/4 SCREW, #8 X 1/2 HEX TAPIT SHT MTL TYPE AB SCREW #8 X 1/2 AB SMS PHL TRUSS LGM NI PLT SCREW, 8-32 x 3/8, PHILLIPS, PAN HEAD BUSHING, STRAIN RELIEF SR-7W-2 CORDSET, ASSY 208/240V (CORD 85640) TERMINAL BLOCK 300V-30AMPS LABEL, XTRM CONTROL 3" NUT, KEPS 6-32 FAN GUARD SCREW, 8-32x1-3/4 SLT PAN MS SS NUT, HEX 8-32 SCREW, COUNTERSINK, 6-32X5/16,Z,BLK XTRM-3, INSULATION CENTER PANEL FAN,COOLING,3" DIA, 208/230V XTRM-2 & 3 AIR DEFLECTOR Guard, 3.15 Sq. Fan XTRM-2 3", CONTROL BOX INSULATION WASHER, 1-1/2 RD XTRM-2 3", RIGHT EXTRUSION INSULATION XTRM-2 3", LEFT EXTRUSION INSULATION XTRM-2 3", RIGHT SIDE INSULATION SCREW, 8-32X5/16 PH PAN SS LABEL, SPEED GUIDCAUTION HOT! LABEL, CAUTION HOT! ELEMENT, 208V-1400W ELEMENT, 230/240V-1400W THERMOSTAT, THERM-O-DISC W/MOUNT CLIP BUSHING, .5 HEYCO 2058

*NOT SHOWN

1 1 2

8 10 12

8 12

Page 10

XTRM-3 3 INCH - EXPLODED VIEW

Page 11

XTRM-3 3” PARTS LIST

ITEM P/N DESCRIPTION QUAN

1 2 3 4 5 6 7 8 9

10*

12*

13 14 15 16

18*

19 20 21 22 23 24 25

26 27 28 29 30 31 32 33 34

93230040

93030158 93030159 93030116 93030115 93000225

93230047

38130 38125

93200070

83248 83976 83868 83267

93000226

85149 85144 89184 85284 89076 89030

83261 93230061 70444800

93200066

69104-EGO 69103-EGO

83333 93200036

88705

83880 93200052 93200048 93000233

82902

75617

XTRM 3 3", RIVIET ASSEMBLY XTRM-2 3"-CONTROL PANEL EXTRUSION EXTRUSION, XTRM 2 3" XTRM-2 3", PANEL, LEFT OUTER XTRM-2 3", PANEL, RIGHT SIDE END CAP, F/L & B/R COVER, TOP, XTRM 3 ASSY, CLIP BEARING BEARING FLANGED POLYMER SHAFT, IDLER XTRM BEARING, SHAFT ASSEMBLY, DRIVE SHAFT SPACER, CONVEYOR SHAFT LEG 1" PLASTIC W/CHROME END CAP, B/L & F/R MOTOR, AT'S 208/240V 60HZ VARIABLE MOTOR, AT'S 230V 60HZ VARIABLE BUSHING, .875 HEYCO 2126 FAN, COOLING 4.5" 105CFM 208/230V WASHER, LOCK 1/4 INTERNAL SCREW, 10-32X3/4 SPROCKET, 12 TOOTH 1/4 PITCH 3/8 BORE ASSY, PLATE, CONTROLS 3" XTRM SWITCH, ROCKER ON-OFF PLATE, SPACE, CONTROLS INFINITE SWITCH-EGO (208V) INFINITE SWITCH-EGO (230/240V) RHEOSTAT 208/240 V. PIGGY-BACK TERM XTRM 3, ELEMENT RACK KNOB 039-266 8A BLACK CONVEYOR BELT 79 LINKS ASSY, XTRM 3 FEEDER XTRM-3, TOASTER DRAWER SPROCKET, 32 TOOTH 1/4 PITCH CHAIN, 1/4" DRIVE 67 PITCH KNOB W/NO'S. 0 TO 9

ITEM P/N DESCRIPTION QUAN

1 1 1 1 1 2 1 2 2 1 2 1 2 4 2 1 1 1 1 4 4 1 1 2 1 2

2 1 2 2 1 1 1 1 1 1

35 36 37

38*

39 40

41*

42 43 44 45 46

47*

48 49

50*

51 52 53 54 55 56 57 58 59 60 61 62

64 65* 66* 67*

83821

89061 93000194

93000229

89073

88889 81600087

89111

83277

89145 93230064

89054

85287

89063 94000114 93200084

85281 93000196

85282

93030227

88940 93030230 93030231 93030232

89039 93200303

58081

54021

54032

88951

93230199

69154

89056

89182

BRACKET, BEARING NUT, HEX 10-24 XTRM 2&3, SMALL ELEMENT COVER HEX MACHINE SCREW, #6-32 X 3/4 SCREW, #8 X 1/2 HEX TAPIT SHT MTL TYPE AB SCREW #8 X 1/2 AB SMS PHL TRUSS LGM NI PLT SCREW, 8-32 x 3/8, PHILLIPS, PAN HEAD BUSHING, STRAIN RELIEF SR-7W-2 CORDSET, ASSY 208/240V (CORD 85640) TERMINAL BLOCK 300V-30AMPS LABEL, XTRM CONTROL 3" NUT, KEPS 6-32 FAN GUARD NUT, HEX 8-32 SCREW, COUNTERSINK, 6-32X5/16,Z,BLK XTRM-3, INSULATION CENTER PANEL FAN,COOLING,3" DIA, 208/230V XTRM-2 & 3 AIR DEFLECTOR Guard, 3.15 Sq. Fan XTRM-2 3", CONTROL BOX INSULATION WASHER, 1-1/2 RD XTRM-2 3", RIGHT EXTRUSION INSULATION XTRM-2 3", LEFT EXTRUSION INSULATION XTRM-2 3", RIGHT SIDE INSULATION SCREW, 8-32X5/16 PH PAN SS LABEL, SPEED GUIDCAUTION HOT! LABEL, CAUTION HOT! ELEMENT, 208V - 1650W ELEMENT, 230/240V - 1650W SCREW, 8-32x2" PHILLIPS PAN MS SS XTRM 3 3", BACK COVER THERMOSTAT, THERM-O-DISC W/MOUNT CLIP WASHER #8 INTERNAL LOCK, SS BUSHING, .5 HEYCO 2058

*NOT SHOWN

8 10 12

9 12

Page 12

10. APW WYOTT EQUIPMENT LIMITED WARRANTY

APW Wyott Foodservice Equipment Company warrants it's equipment against defects in materials and workmanship, subject to the following conditions:

This warranty applies to the original owner only and is not assignable. Should any product fail to function in its intended manner under normal use within the limits defined in this warranty,at the option of

APW Wyott such product will be repaired or replaced by APW Wyott or its Authorized Service Agency.APW Wyott will only be responsible for charges incurred or service performed by its Authorized Service Agencies. The use of other than APW Wyott Authorized Service Agencies will void this warranty and APW Wyott will not be responsible for such work or any charges associated with same.TheclosestAPWWyottAuthorized ServiceAgentmustbeused.

This warranty covers products shipped into the 48 contiguous United States, Hawaii, metropolitan areas of Alaska and Canada. There will benolaborcoverage for equipment located on any island not connected by roadway to the mainland.

Warranty coverage on products used outside the 48 contiguous United States, Hawaii, and metropolitan areas of Alaska and Canada may vary. Contact the international APWWyott distributor,dealer, or service agency for details.

TimePeriod

One year for parts and one year for labor, effective from the date of purchase by the original owner.The Authorized Service Agency may, at their option, require proof of purchase. Parts replaced under this warranty are warranted for the un-expired portion of the original product warranty only.

Exceptions

Inallcases,partscovered by extended warranty will be shipped FOB the factory after the first year.

Portable Carry In Products

Equipment weighing over 70 pounds or permanently installed will be serviced on-site as per the terms of this warranty. Equipment weighing 70 pounds or under, and which is not permanently installed, i.e. with cord and plug, is considered portable and is subject to the following warranty handling limitations. If portable equipment fails to operate in its intended manner on the first day of connection, or use, atAPWWyott's option or itsAuthorizedServiceAgency, it will be serviced on site or replaced.

From day two through the conclusion of this warranty period, portable units must be taken to or sent prepaid to the APW Wyott Authorized ServiceAgency forin-warranty repairs. No mileage or travel charges are allowed on portable units after the first day of use. If the customer wants on-site service, they may receive same by paying the travel and mileage charges. Exceptions to this rule: (1) countertop warmers and cookers,which are covered under the Enhanced Warranty Program, and (2) toasters or rollergrills which have instoreservice.

Exclusions

The following conditions are not covered by warranty:

If the equipment has been changed, altered, modified or repaired by other than an Authorized Service Agency during or after the warranty period, then the manufacturer shall not be liable for any damages to any person or to any property,whichmay result from the use oftheequipment thereafter.

This warranty does not cover services performed at overtime or premium labor rates. Should service be required at times which normally involve overtime or premium labor rates,theownershallbechargedforthedifferencebetween normal service rates and such premium rates.APWWyott does not assume any liability for extended delays in replacing or repairing anyitemsbeyonditscontrol.

Inallcases,theuseofotherthanAPWWyottAuthorized OEM Replacement Partswill void this warranty. This equipment is intended for commercial use only.Warrantyis void if equipment is installed in other than commercial application.

WaterQuality Requirements

Water supply intended for a unit that has in excess of 3.0 grains of hardness per gallon (GPG) must be treated or softened before being used. Water containing over 3.0 GPG will decrease the efficiency and reduce the operation life of the unit.

Note: Product failure caused by liming or sediment buildup is not covered under warranty. THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED

INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSES AND CONSTITUTES THE ENTIRE LIABILITY OFAPW WYOTT. IN NO EVENT DOES THE LIMITED WARRANTY EXTEND BEYOND THE TERMS STATED HEREIN.

*Gas/Electric Cookline:

component parts, except switches and thermostats. (2additionalyearsonpartsonly.No labor on second or third year.)

*BroilerBriquettes, *Heat Strips: *GlassWindows, Doors, Seals,Rubber Seals, Light Bulbs:

*Equipment failure relating to improper installation, improper utility connection or supply and problems due to ventilation. *Equipment that has not been properly maintained, calibration of controls, adjustments, damage from improper cleaning and water damage to controls. *Equipment that has not been used in an appropriate manner, or has been subject to misuse or misapplication, neglect, abuse, accident, alteration, negligence, damage duringtransit,delivery orinstallation, fire, flood, riot or act ofgod. *Equipment that has the model number or serial number removed or altered.

Models FD, FDL, FDD, FDDL. Two(2) YearWarranty on element only. No labor second year.

Models GCB, GCRB, GF, GGM, GGT, CHP-H, EF, EG, EHP. Three (3) Year Warranty on all

RockGrates, Cooking Grates, Burner Shields,Fireboxes:

90Day Material Only. No Labor.

90Day Material Only.No Labor.

9/05