APW Wyott VSX10, VCX-10 Installation Manual

R

INSTALLATION

AND

OPERATING

INSTRUCTIONS

TM

X’Vert

Model: VSX

VERTICAL CONTACT BUN GRILL TOASTER

INTENDED FOR OTHER THAN HOUSEHOLD USE

RETAIN THIS MANUAL FOR FUTURE REFERENCE

TOASTER MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

WARNING: Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the Installation, Operating and
Maintenance Instructions thoroughly before installing or servicing this equipment.

Initial heating of toaster may generate smoke or fumes and must be done in a well ventilated area.
Overexposure to smoke or fumes may cause nausea or dizziness.

This equipment has been engineered to provide you with year-round dependable service when used
according to the instructions in this manual and standard commercial kitchen practices.

ANSI/NSF4

P/N 81603377 9/05

Phone:
Fax: [phone]
Toll Free: [phone]
Website: www.apwwyott.com
E-mail: [e-mail]

[phone]

APW / WYOTT

729 Third Avenue

Dallas, TX 75226

!!

!!

1

TABLE OF CONTENTS

SECTION ITEM PAGE

1 Owner’s Information
2 Safety Information
3 Specifications
4 Operation
5 Cleaning & Release Sheet Care & Replacement
6 Troubleshooting
7 Preventative Maintenance Schedule
8 Wiring Diagram
9 Parts List & Exploded View
10 Procedure: Conveyor Belt Tracking
11 Procedure: Changing a Belt
12 Procedure: Splicing The Conveyor Chain
13 Procedure: Conveyor Belt Adjustment
14 Warranty

........

2
2
3

..

4
6
7
10
13
14
16
16
17
19
20

1. OWNER’S INFORMATION

General Information:

The APW Wyott X’Vert Vertical Contact Bun Grill Toaster (VSX) is designed to toast two whole buns (2
crowns and 2 heels) at the same time. (See page 5, Figure 4) Toasting is accomplished through contact of
the flat side of the buns with an aluminum griddle plate. The user places both buns into the top of the toaster
and two perfectly caramelized, warm buns (4 halves) will slide out of the bun chute. The VSX will toast two
buns in 8, 20 or 30 seconds (dependingon your model).

TM

The Manual includes information for proper procedures on safety, installation and operation of the Vertical
Contact Bun Grill Toaster (VSX). It is of extreme importance that this manual be read in its entirety before
installing and operating this unit.

This Vertical Contact Bun Grill Toaster (VSX) is manufactured of the highest quality materials available and
is built to the stringent quality standards of APW Wyott. Quality Assurance testing is one of the standards
that we adhere to.

Please keep this manual for future reference. It contains important instructions for the proper installation,
operation and service of this unit. If this unit changes ownership, it is important that this manual accompany
the equipment.

WarrantyInformation:

Reliability backed byAPW Wyott’s Warranty:

All APW Wyott Bun Grill Toasters are backed by a 1-year Parts and Labor warranty, including On-Site
Service calls within 50 miles of authorized service technicians.

Service Information:

Service Hotline [phone]

2. SAFETY INFORMATION

APW Wyott toasters are designed, built, and sold for commercial use and should be operated by trained
personnel only. Clearly post all CAUTIONS, WARNINGS and operating instructions near each unit to
insure proper operation and to reduce the chance of personal injury and/or equipment damage.

Always disconnect power before servicing the toaster. Surfaces will remain hot after power has been
turned off. Allow unit to cool before cleaning or servicing. Never clean the toaster by immersing it in water.
The toaster is not protected against water jets; DO NOT CLEAN TOASTER WITH A WATER JET. Always
clean equipment before first use.

2

Operating toaster without legs will void the warranty. Insure all accessories and exterior panels are properly
installed and adjusted before applying power and operating.

3. SPECIFICATIONS

Cordset Configuration:

208/240V: NEMA6-20P plug, 3 foot, 3 wire grounded cord.
208/240V: NEMA6-20P plug (90° angle), 5 foot, 3 wire grounded cord.

If the supply cord is damaged, the manufacturer or an authorized service agent (or a similarly qualified
person) must replace it to avoid a hazard.Failure to replace a damaged cord will voidthe warranty.

Overall Dimensions:

VSX: 24”H x 19”W x 11” D
(61 cm x 48 cm x 28 cm) VSX: 240V - 3420W, 14.5 Amps 60HZ

WARNING:

INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SERIOUS INJURY OR
DEATH.

Electrical Ground is required on this appliance.

!

Do not modify the power supply cord plug. If it does not fit into the outlet, have
the proper outlet installed by a qualified electrician
Do not use an extension cord with this appliance.
Check with a qualified electrician if you are unsure as to whether the appliance
is properly grounded.

Electrical Ratings:

VSX: 208V - 2570W, 12.5 Amps 60HZ

ELECTRICAL SHOCK HAZARD. FAILURE TO FOLLOW THE

FIGURE 1: DIMENSIONS

G

NEMA-6-20P

20Amp, 250 VAC

!

18.24"

19.38"

18.67

23.90"

22.64"

10.00

"

3

13.17"

"

4. OPERATION

Operating Instructions (see figure #4)

Dry operation onlyThis toaster is for (no oil). Do not put buttered bread products in the toaster.

!

Ensure Release Sheets are properly installed. (See page 7.)

!

Turn Main Power Switch on. Set Temperature Control to desired temperature. (Temperature is factory

set at 600°F.)

!

Allow Pilot Light to cycle at least two times (on/off). When the light is on, the grill is heating. Heat up time
is about 15 minutes.

!

Place bun halves on feeder cut side down (facing grill

surface). Toast time is approximately 8, 20 or 30
seconds depending on bun height, diameter and model
purchased. Increase or decrease temperature setting
and/or Bun Thickness Dials to achieve desired
brownness and temperature.

Bun Thickness Adjustment

The VSX is designed to accommodate a variety of different
products. Adjust for product thickness by setting the Bun
Thickness Dials on the side of the toaster to the appropriate
setting. Settings for different thicknesses are indicated on
the label adjacent to the Bun Thickness Dials.See figure 2.

BUN THICKNESS DIALS

FIGURE 2:

VSX-20 TemperatureControl (See Figure 3)

FIGURE: 3

VSX-20

UP: While pressed, displays the set-point. Press and hold for at

least 3 seconds to increase set point.

DOWN: While pressed, displays the set-point. Press and hold for at

least 3 seconds to decrease set point.
TEMP: Press to momentarily display the actualplaten temperature.
PILOT: Illuminated when power is being applied to heater.
POWER: Main power supply to the toaster.

Operation of Controller (See Figure 3)

1. Make sure that all the doors are closed and the lid is on. (It should
look like the photograph on the cover.)

2. Make sure toaster is plugged in to the correct voltage. The voltage
of the toaster is written on the data plate. The data plate is located
on the back of the toaster near the cord.

3. Turn the toaster on (POWER). “|” is on and “O” is off.

4. When main power is applied, the digital display will boot up (displays “888” and then the software
version information). Then it will display “Lo.” (If the toaster is already warm, it might display “Hi.”)

5. The toaster remembers the last set point that was entered, even if you turn the toaster off. APW
recommends a set point of 600°F or below. If you wish to change the set point, press (and hold)
either the UP or DOWN key. Display will change set point by 1 degree for the first 5 degrees, and
then it will jump by 5's. When you reach the set point that you want, let go of the button. You may
then press the UP or DOWN key to make further changes. If you don't press any buttons for 5
seconds, then the new set point will take effect.

6. When the set point is changed, the display will say “Lo” or “Hi” until the set point is reached. After
that time it will say “rdY.” While it says “rdY” the platen will cycle on and off to maintain the set point.
Whenever heat is applied to the platen, the PILOT LED will be illuminated.

7. It takes the toaster 10-15 minutes to warm up.

TEMP. CONTROL

ALARM

PILOT

TEMP

DOWN

UP

4

Status,Alarm, and ErrorMessages (See Figure 3)

rdY
Lo

Hi
Prb
HIE

Control is at set point and the toaster is ready for operation.
Actual temperature is below set point. After toaster has reached “rdY,” then this indicates
that the platen is less than 50°F below the set point (too cold).
Actual temperature is above set point.
The temperature probe (sensor) is disconnected or defective.
Actual temperature is at least 50°F above set point, indicating that there is a controller error.

FIGURE 4: TYPICAL

TOASTER OPERATION

HEEL IN

BACK

DISCHARGE

CROWN
IN FRONT

BUN

FIGURE 5:

VSX-20 W/BUN CATCHER

“If you like to keep
your counter clean,
APW Wyott also
offers a bun catcher.
This is a bun chute
that will catch the
crumbs that fall down
the bun chute. The
bun catcher is part
number 81699002.”

VSX-10 Temperature Control (See Figure 6)

NO HEAT: When the knob is pointed here, all heat is cut off from the

platen. The conveyors will run, but the platen will not heat.
PILOT: Illuminated when power is being applied to heater.
KNOB: Usedto select the set point. Graduations are °F.
POWER: Main power supply to the toaster.

Operation of Controller (See Figure 6)

1. Make sure that all the doors are closed and the lid is on. (It
should look like the photograph on the cover.)

2. Make sure toaster is plugged in to the correct voltage. The
voltage of the toaster is written on the data plate. The
data plate is located on the back of the toaster near the
cord.

3. Turnthe toaster on (POWER). “|” is on and “O” is off.

4. Turn the dial to the desired set point. APW recommends
that you set it to 600°F or below. If the dial is set to “NO
HEAT” then the toaster will run normally except that there
will be no more heat supplied to the toaster. The toaster will
cool down to room temperature.

5. Whenever heat is applied to the platen, the PILOT light will
be illuminated. When the pilot light has cycled a couple of
times (turned off and on, twice), then the toaster is ready
for toasting. This takes 10-15 minutes.

FIGURE 6:

VSX-10

TEMP. CONTROL

PILOT

5

Cleaning Instructions

5. CLEANING

Toaster is for DRY BUNS ONLY.

Do not put buttered bread products in

the toaster.

Note: To save time at closing (it will take 15 minutes for toaster to cool
down), you might want to have the day shift clean the toaster.

1. Turn off (7) Main Power Switch (See Fig. 7). Allow toaster to cool down.

2. Remove (6) Bun Slide and (1) Top Cover (See Fig. 7) & wash in sink.

3. For ease of cleaning, turn the toaster so that you can access the
conveyor.

4. Lift up and lower (5) Front Panel (See Fig. 7).

5. Depress (9) Conveyor Button (See Fig. 7). Using a cloth or sponge,
and Sizzle Plus (from Kay Chemical, www.ecolab.com), wipe (4)
belting back and forth removing bread crumbs and
debris. Continue until belting is clean. (See Figure 8)

6. Close (5) Front Panel (See Fig. 7).

7. Lift up and lower (8) Back Panel (See Fig. 7).

8. Repeat step five.

9. Close (8) Back Panel (See Fig. 7).

10. Rotate (3) BunThickness Dials to the vertical position.

11. Clean (2) Release Sheet (See Fig. 7) according to the instructions on
page 7.
Replace (1) Top Cover (See Fig. 7).

12.
Rotate (3) BunThickness Dials to their original position.

13.
Turn on (7) Main Power Switch (See Fig. 7).

14.

TM

FIGURE 7:

TOASTER PARTS

(PIEZAS DE LA TOSTADORA)

1

9

8

4

3

7

6

2

5

5. CLEANING (EN ESPAÑOL)

El Procedimiento de Limpieza

Tostador es SOLO PARALOS BOLLOS SECOS.

en la tostadora.

Nota:

Para ahorrar tiempo al cerrar (Hay que esperar 15 minutos para que el tostador se pueda enfriar) usted

puede decirle al los trabajadores del horario diurno que deben limpiar el tostador.

1. Apagar usando (7) el interruptor principal (mirar la 7 figura). Darle un tiempo al tostador de enfriarce.

2. Quitar (6) el deslizador de los bollos y (1) la cubre tapa (mirar la 7 figura) y lavar en el regadero.

3. Para la facilidad de la limpieza, dé vuelta a la tostadora de modo que usted pueda tener acceso al
transportador.

4. Levantar y bajar (5) el panel delantero del tostador (mirar la 7 figura).

5. Deprimir (9) el botón de la correa transportadora (mirar la 7 figura)
Usando un trapo o esponja y Sizzle Plus (de Kay Chemical,
www.ecolab.com), limpiar (4) la correa adelante y atras quitando las
migajas de pan y otros escombros. Continuar hasta que la correa este
limpia. (Mirar la 8 figura)

va

6. Cerrar (5) el panel delantero.

7. Levantar y bajar (8) el panel detrás de el tostador (mirar la 7 figura).

8. Repetir el paso número cinco.

9. Cerrar (8) el panel detrás.

10. Girar (3) los diales que específica lo grueso de los bollos a la posición

vertical.

11. Limpie (2) la Hoja de Salida (mirar la 7 figura) según las

instrucciones en la página 7.

12. Reemplazar (1) la cubre tapa (mirar la 7 figura).

ma

13. Girar (3) los diales que específica lo grueso de los bollos a su posición

original.

14. Poner en marcha usando (7) el interruptor principal (mirar la 7 figura).

No ponga los productos de pan untados con mantequilla

ma

ma

ma

ma

TM

FIGURE 8:

CLEANING THE BELT

(LIMPIEZA DE LA CORREA)

ma

ma

ma

6