APW Wyott FLEXWAV-1422 EZ Service Manual
INSTALLATION
AND
OPERATING
INSTRUCTIONS
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
WARNING: Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the Installation, Operating and Maintenance
Instructions thoroughly before installing or servicing this equipment.
US
C
U
L
ANSI/NSF4
U
L
APWWYOTT
729 Third Avenue
Dallas, TX 75226
Models: FLEXWAV-1422 EZ, -1829 EZ, -1422 EZ SS & -1829 EZ SS
PASS THROUGH TOASTER
INTENDED FOR OTHER THAN HOUSEHOLD USE
RETAIN THIS MANUAL FOR FUTURE REFERENCE
UNIT MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES
Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or
death. Read the Installation, Operating and Maintenance Instructions thoroughly before installing or servicing
this equipment.
This equipment has been engineered to provide you with year-round dependable service when used according
to the instructions in this manual and standard commercial kitchen practices.
Phone: +1 (214) 421-7366
Fax: +1 (214) 565-0976
Toll Free: +1 (800) 527-2100
Website: www.apwwyott.com
E-mail: info@apwwyott.com
1
P/N 79967150 12/09
IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual for the life of the equipment. For
Warranty Service and/or Parts, this information is required.
Model Number
Serial Number
Date Purchased
SECTION
ITEM
PAGE
SECTION
ITEM
PAGE
1
Owner’s Information
2 7
Cleaning
7
2
Safety Information
2 8
Troubleshooting
8
3
Specifications
3 9
Preventative Maintenance
8
4
Installation Instructions
4 10
Wiring Diagrams
9
5
Operation
5 11
Parts Lists & Exploded Views
17
6
Programming
6 12
Warranty
20
WARNING: In Europe, appliance must be connected by an earthing cable to all other units
in the complete installation and thence to an independent earth connection in compliance
with EN 60335-1 and/or local codes.
WARNING: An earthing cable must connect the appliance to all other units in the
complete installation and from there to an independent earth connection.
TABLE OF CONTENTS
1. OWNER’S INFORMATION
General Information:
1. Always clean equipment thoroughly before first use. (See general cleaning instructions).
2. Check rating label for your model designation and electrical rating.
3. For best results, use stainless steel counter tops.
General Operation Instructions:
1. All food-service equipment should be operated by trained personnel.
2. Do not allow your customers to come in contact with any surface labeled "CAUTION HOT".
3. Never touch ceramic or steel heaters.
Warranty Information:
Reliability Backed By APW Wyott’s Warranty:
All APW Wyott Pass Through Ovens are backed by a one year parts and labor warranty, including On-Site
Service calls within 50 miles of authorized service technicians.
Service Information:
Service Hotline (800) 733-2203
2. SAFETY INFORMATION
APW Wyott equipment is designed, built and sold for commercial use and should be operated by trained
personnel only. Clearly post all CAUTIONS, WARNINGS and OPERATING INSTRUCTIONS near each unit to
insure proper operation and to reduce the chance of personal injury and/or equipment damage. This product is
used for the cooking, defrosting or re-thermalization of food products only.
Always disconnect power before servicing the unit. Surfaces will remain hot after power has been turned off.
Allow unit to cool before cleaning or servicing. Never clean the unit by immersing it in water. The unit is not
protected against water jets; DO NOT CLEAN PASS THROUGH OVEN WITH A WATER JET. Always clean
equipment properly before first use.
2
3. SPECIFICATIONS
FLEXWAV SS MODEL
VOLTS
WATTS
PH A B C D
E
96610002
208V
6100W
1
44.675
15.125
23.4
16.13
22.45
96610001
208V
7000W
1
44.675
15.125
23.4
16.13
22.45
96610000
208V
7000W
3
44.675
15.125
23.4
16.13
22.45
96612000
240V
7000W
3
44.675
15.125
23.4
16.13
22.45
96611000
208V
9000W
3
44.675
15.125
23.4
16.13
22.45
96613000
240V
9000W
3
51.675
19.125
30.4
16.13
26.45
96616000
208V
9000W
1
51.675
19.125
30.4
16.13
26.45
96617000
240V
9000W
1
51.675
19.125
30.4
16.13
26.45
96615000
230/400V
9000W
1
51.675
19.125
30.4
16.13
26.45
FLEXWAV1422 EZ
FLEXWAV 1829 EZ
FLEXWAV1422 EZ SS
FLEXWAV1829 EZ SS
115 lbs. (52.2 kg.)
149 lbs. (67.6 kg.)
115 lbs. (52.2 kg.)
149 lbs. (67.6 kg.)
Power Cord:
Six (6) foot, 3 wire grounded cord. If the supply cord is damaged, the manufacturer, or an authorized service
agent, must replace it in order to avoid a hazard and warranty. Please contact the factory by calling the 800 #
located on the unit.
Shipping Weight:
3
4. INSTALLATION INSTRUCTIONS
CAUTION: The Pass Through Oven is shipped assembled. The unit is shipped with
urethane supports between the top heaters and the conveyor assembly. Please remove all
urethane supports and packaging materials before operating the unit. Failure to remove all
packaging materials may lead to a fire and / or damage to the appliance.
If the carton appears damaged, or damage is discovered once the carton is opened, stop
immediately and contact the freight company to file a damage claim.
1. Remove all external packaging that is protecting top portion of unit
2. Remove unit from shipping container while in the upright position. The unit can be lifted out of the carton
by grasping under the conveyor on each side of the appliance. Please remove the plastic bag.
3. Remove all internal packaging to the unit. Important: Remove urethane supports located inside the
tunnel oven between the top heaters and the conveyor. Remove tape from conveyor trays. Remove
tape from extrusion corners. Remove tape from deflecting curtains located just above entrance and exit
of conveyor.
4. Visually inspect all external and internal portions of unit for damage. Important: Inspect the top white
ceramic elements located inside the oven tunnel after removal of urethane supports. To inspect
these white ceramic elements, use a small mirror held under each element to detect cracks.
Important: The Ceramic elements are fragile and will break under stress. Do not twist, pull, push,
or otherwise subject the white ceramic elements to stress.
5. Wipe down the exterior of the unit using a damp cloth with warm water. Do not use abrasive pads or
cleaners as they will damage the stainless steel surface and high temperature plastic.
NOTE: DO NOT USE CLEANERS OF ANY KIND ON THE WHITE CERAMIC HEATERS.
6. Remove four feet from box and install into threaded nuts located at the four corners underside of the left
and right housings; Also remove conveyor extension tray(s) . Conveyor extensions should be hung
offend of conveyor frame. Model FLEXWAV 1422EZ and FLEXWAV 1829EZ will have two conveyor
extensions for loading and exit ends.
7. Place unit in operating location.
Note: Ambient Conditions - Make sure that the operating location is in an area where the ambient
temperature is held constant (minimum 70°F). Please avoid areas such as near exhaust fans and air
conditioning ducts.
Warning: Operating environment
Ensure that operation location is at a reasonable distance from combustible walls and materials
otherwise combustion or discoloration could occur. Stand-off/Air-divider located on rear panel is
important in maintaining proper division of inlet and exhaust air flow - If removed it could result in
Improper functioning of unit and MAY cause personal injury and WILL void your warranty.
Caution: Operating environment
Place unit on a stable, level counter at a convenient height for use. Turn the adjustable feet so that
unit is level to counter top. The top of the unit is not intended for use a shelf. Materials placed there
are at risk for fire.
8. Before plugging unit into wall, make sure that the switch is in the off position.
9. Warning: Ensure no hands, tools or parts or other unintended items are located on the conveyor as
injury will result when unit is turned on.
10. Plug unit into grounded electrical outlet with correct voltage, and plug configuration.
Warning: Using any receptacle that is not designed to match the attached cord and plug MAY cause
personal injury and WILL void your warranty. Please attach the FLEXWAV1422/Medium Size unit, 208V,
5400W only, to an individual branch circuit.
4
Oven Stacking:
FIGURE 1
The stacking kit will consist of 4 corner posts to be inserted
between stacked units.
Warning: When stacking, unit must have proper
stacking kit installed. This will prevent overheating
and damaging of electrical components.
Warning: Do not stack more than three units tall or
do not use more than two stacking kits.
Warning: Standoff on rear panel of unit is important
to allow proper inlet and exhaust fan airflow. Do not
cover inlet or exhaust fan openings as this could
damage electrical components.
1. Ensure bottom unit is mounted on secure surface,
with feet installed.
2. Remove respective corner end caps and screws.
This will allow each of the stacking spacer
retaining fingers to slide into the extrusions.
3. Remove the feet from the top unit as shown.
4. Secure each stacking spacer to the bottom of the
unit as shown by using the bolts and washers
provided. You should have four total of each.
5. Once the stacking kit spacers are secure, place
top unit onto bottom unit. The stacking kit spacers
each have tapered guides to allow the unit to lock
into position.
6. Refer to Cleaning Instructions for cleaning of
stacking spacers and cleaning between units.
5. OPERATION
1. The controls that operate the belt conveyor and the heaters are located on the front of the unit.
2. A. The On/Off switch is used to turn the unit on or off. Once the unit is turned on the conveyor will
automatically run. Warning: Ensure no hands, tools or parts are located on the conveyor as injury will
result when unit is turned on.
B. The direction of the belt conveyor travel is controlled by a hidden rocker switch located beneath the left
side conveyor extension, behind a removable cover attached to the base housing panel. To change belt
direction, remove this cover, flip the rocker switch to the opposite setting, and replace the cover. This
operation can be performed while the belt is moving.
3. Note: Before moving the On / Off switch to the "On" position, please read the following statements:
4. A. CAUTION: HOT SURFACES! The exterior metal surfaces of the unit will get hot enough to cause burns.
Avoid touching these surfaces to prevent injury.
B. WARNING: SEVERE BURN HAZARD CERAMIC HEATERS (top heaters). The white ceramic heaters
located in the top of the unit operate at very high temperatures. DO NOT TOUCH HEATERS AFTER
UNIT IS TURNED ON.
5. Two adjustable deflector shields are located at the inlet/outlet of the unit, above the conveyor belt. These
shields are designed to keep maximum heat inside the unit. Position the shields as needed for product flow.
CAUTION HOT SURFACE!
6. This oven has 2 heating zones, 1 on top, and a bottom one.
5
Loading...