APW Wyott FD-18L, FD-36L, FD-42H, FD-24L, FD-30H Installation And Operating Instructions Manual

INSTALLATION

AND

OPERATING

INSTRUCTIONS

Models: FD, FDD, FDL & FDDL

OVERHEAD WARMERS

INTENDED FOR OTHER THAN HOUSEHOLD USE

RETAIN THIS MANUAL FOR FUTURE REFERENCE

UNIT MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES

R

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

WARNING: Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the Installation, Operating and
Maintenance Instructions thoroughly before installing or servicing this equipment.

Initial heating of unit may generate smoke or fumes and must be done in a well ventilated area.
Overexposure to smoke or fumes may cause nausea or dizziness.

This equipment has been engineered to provide you with year-round dependable service when used
according to the instructions in this manual and standard commercial kitchen practices.

ANSI/NSF4

P/N 70400000 Rev. 3/06

Phone:
Fax: [phone]
Toll Free: [phone]
Website: www.apwwyott.com
E-mail: [e-mail]

[phone]

APW WYOTT

729 Third Avenue

Dallas, TX 75226

!!

!!

1

TABLE OF CONTENTS

SECTION

1

2

3

4

5

6

7

ITEM

Owner’s Information

General Information
Installation Instructions
General Operation Instructions
Warranty Information

Important Safety Information

Specifications

Electrical
Dimensions

Operation

Operating Instructions

Cleaning

General Cleaning Instructions

Troubleshooting

Wiring Diagrams

FD Wiring Diagrams
FDL Wiring Diagrams
FDD Wiring Diagrams
FDDL Wiring Diagrams

.

PAGE

2
2
3
4
4

4

4
4
5

6
6

6
6

6

7
7
8
9

10

8

9

Parts Lists

FD Replacement Parts
FDL Replacement Parts
FDD or FDDL Replacement Parts

Warranty

11
11
14
17

20

1. OWNERS INFORMATION

General Information:

1. Always clean equipment thoroughly before first use. (See general cleaning instructions).

2. Check rating label for your model designation and electrical rating.

3. For best results, use stainless steel countertops.

4. All dimensions in parenthesis in centimeters unless noted.

5. APW Wyott Overhead Foodwarmers are constructed from high quality stainless steel and available
in lengths from 18" to 96”. Utilizing a metal sheath-heating element with a specially designed reflector,
these units give uniform heat over the entire holding surface.

6. In Europe, contact anAPW Wyott authorized serviceagency for replacement light bulbs.

Installation Instructions:

A. Always cleanequipment thoroughly before first use (See cleaning instructions).
B. Provide the following clearances around foodwarmer:

2

Do not install A = Minimum clearance (in inches) to

closer than:

B.

= Minimum clearance (in inches) to

C

= Minimum clearance (in inches) to

Bottom Surface of unit from Tabletop
Back of unit
Sides of unit.

CLEARANCES FOR OVERHEADS

HIGH WATTAGE LOW WATTAGE

MODEL A B C A B C

FDD/FDDL-18
FDD/FDDL-24
FDD/FDDL-30
FDD/FDDL-36
FDD/FDDL-42
FDD/FDDL-48
FDD/FDDL-54
FDD/FDDL-60
FDD/FDDL-66
FDD/FDDL-72
FDD/FDDL-84
FDD/FDDL-96
FD/FDL-18
FD/FDL-24
FD/FDL-30
FD/FDL-36
FD/FDL-42
FD/FDL-48
FD/FDL-54
FD/FDL-60
FD/FDL-66
FD/FDL-72
FD/FDL-84
FD/FDL-96

28
28
28
28
28
28
28
28
28

28
N/A
N/A

16

16

16

16

16

16

16

16

16

16
N/A
N/A

12
12
12
12
12
12
12
12
12

12
N/A
N/A

2
2
2
2
2
2
2
2
2

2
N/A
N/A

2
2
2
2
2
2
2
2
2

2
N/A
N/A

2

2

2

2

2

2

2

2

2

2
N/A
N/A

24
24
24
24
24
24
24
24
24
24
24
24
16
16
16
16
16
16
16
16
16
16
16
16

12
12
12
12
12
12
12
12
12
12
12
12

2
2
2
2
2
2
2
2
2
2
2
2

2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

C. Consult foodwarmer rating labelfor model designation and correct operating voltage and amperage.
D. Ceiling mounting brackets are provided with each foodwarmer for chain or shelf mounting. Remove

brackets form packaging and screws from ends of foodwarmer to attach brackets. Use four #10 screws
or studs with locknuts for shelf mounting. For chain mounting, use #14 jack chain and “S” hooks.

E. Remote switches are recommended. Longer switch life will result from cooler switch mounting

locations. Optional stainless steel remote toggle and infinite switch box kits are available. Installation
of remote switch box by service personnel requires 7/8" conduit, 1/4" push-on terminals, and no. 14
AWG copper wire suitable for at lest 90ºC. Mount remote box to flat surface with two #10 screws or
studs with locknuts. All wires marked as shown on wiring diagram.

F. Optional tubular stands are available for permanently mounting foodwarmers to non-combustible

countertops.
G. Optional portable legs are available for foodwarmers for use over non-combustible countertops.
H. Installation of cord sets by service personnel should utilize the strain relief, grounding stud, and

porcelain wire nuts provided with foodwarmers.
I. If unit is supplied with a power cord, the appliance must be positioned so that the plug is accessible.

NOTE: TO AVOID BURNING OR CHARRING OF MATERIALS IN THE SURFACE
BELOW THE FOODWARMER USE ONLY ABOVE AN ALL-METAL STRUCTURE
SUCHASATABLE OR COUNTERTOP. SEE MINIMUM CLEARANCE CHARTABOVE.

!!

REMOTE SWITCHES ARE RECOMMENDED FOR UNDER SHELF MOUNTING.
LONGER SWITCH LIFE WILL RESULT FROM COOLER SWITCH MOUNTING
LOCATIONS.

3

General Operation Instructions:

1. All foodserviceequipment should be operated by trained personnel.

2. Do notallow your customers to come in contact with any surfacelabeled “CAUTION HOT”.

3. Never holdfood below 150°F (66°C).

Warranty Information:

Reliability Backed By APW Wyott’s Warranty:

All APW Wyott Overhead Warmers are backed by a one year parts and labor warranty, including On-Site
Service calls within 50 miles of authorized service technicians.

Service Information:

Service Hotline [phone]

2. SAFETY INFORMATION

APW Wyott Overhead Warmers are designed, built and sold for commercial use and should be operated by
trained personnel only. Clearly post all CAUTIONS, WARNINGS and OPERATING INSTRUCTIONS near
each unit to insure proper operation and to reduce the chance of personal injury and/or equipment damage.

Always disconnect power before servicing the Overhead Warmer. Surfaces will remain hot after power has
been turned off. Allow unit to cool before cleaning or servicing. Never clean the Overhead Warmer by
immersing it in water. The Overhead Warmer is not protected against water jets; DO NOT CLEAN
OVERHEAD WARMER WITH A WATER JET. Always clean equipment before first use.

3. SPECIFICATIONS

Electrical:

A. Single-phase operation at 120,208, 230, and 240 volts. (See label on each unit).
B. Field-wired units provided with 7/8" conduit hole, 6" long leads, and porcelain wire nuts. For supply

connections, use minimum no. 14AWGcopper wires suitable for at least 90ºC.
C. U.S. cord-connectedunits provided with following plug configuration:

1. 120 volt up to1440 watts = NEMA 5-15P; 120 voltup to 1920 watts = NEMA 5-20P

2. 208 volt up to2496 watts = NEMA 6-15P; 208 voltup to 3328 watts = NEMA 6-20P

3. 240 volt up to2880 watts = NEMA 6-15P; 240 voltup to 3840 watts = NEMA6-20P

D European cord-connected units provided with following plug configuration:

1. Continental Europe230 volt up to 3600 watts = Schuko CEE7/7

2. UK230 volt up to2930 watts = Bs1363

If the supply cord is damaged, an authorized service agent or a similarly qualified person must replace it to
avoid a hazard or voiding the warranty.

4

WARNING: ELECTRICAL SHOCK HAZARD. FAILURE TO FOLLOW THE

INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SERIOUS INJURY OR

!

DEATH.

Electrical Ground is required on this appliance.
Do not modify the power supply cord plug. If it does not fit into the outlet, have
the proper outlet installed by a qualified electrician
Do not use an extension cord with this appliance.
Check with a qualified electrician if you are unsure as to whether the appliance
is properly grounded.

Overall Dimensions:

!

FD MODELS

OVERHEAD WARMER LENGTH

18.00 [45.72] TO 72.00 [182.88]

RATING LABEL

FDL MODELS

PILOT LIGHT

.75

[1.91]

[ 23.18 ]

POWER LEADS

3.58

[9.09]

TOGGLE OR INFINITE SWITCH

9.125

10.048

[ 25.52 ]

.875 [ 2.22 ] CONDUIT HOLE

6.000

[ 15.24 ]

6.923

[ 17.58 ]

MOUNTING BRACKETS

FDD, FDDL MODELS

1.00

[2.55]

15.125

[ 38.42 ]

[ 43.11]

16.971

TUBULAR STAND KIT

FOR INSTALLATION ABOVE NONCOMBUSTIBLE SURFACE

1.00[2.54] SQUARE
S/S TUBING

5/16 -18 STUD MOUNT

OVERHEAD WARMER LENGTH + 1.06[2.7]

16.00

[

40.64

[ 46.99

]

18.50

PORTABLE LEG KIT

FOR USE ABOVE NONCOMBUSTIBLE SURFACE

]

1.00[2.54] SQUARE
S/S TUBING

OVERHEAD WARMER LENGTH + 2.06[5.23]

16.00

[

40.64

18.50
]

[

46.99

]

11.00[27.94]

11.27[28.63]

5

4. Operation

A. All foodservice equipment should be operated by trained personnel.
B. Do not allow your customers to come in contact with any surface labeled “CAUTION HOT”.
C. Switch on unit. Place precooked product under heat source. Maximum heat coverage equivalent to

unit length.

D. Never holdfood below 150ºF.

5. Cleaning

General Cleaning Instructions:

A. Never clean any electrical unit by immersing it in water.
B. Never clean any electrical unit using water jets.
C. Disconnect power before cleaning or servicing units.

authorized service agency.

D. Clean unit daily. Use warm, soapy water. Mild cleansers and non-abrasive pads may be used to

remove baked-on food.

Turn off before surface cleaning.

All service should be performed by an APW

6. Troubleshooting

A. Always ask and check:

1. Is the unit connected to a live power source?

2. Check the circuit breaker.

3. Is the power switch on and pilot light illuminating?

4. Check the rating label. Is the unit operating on proper voltage?
B. If the above checks out, and problems still exist, call an APW Wyott authorized service agency.
C. All service should be performed by an APW Wyott authorized service agency.

6

GREEN

G

120V: WHITE
200-240V: BLUE

BROWN

7. WIRING DIAGRAMS

FD18-72 WIRING DIAGRAM

REMOTE CONFIGURATION

ELEMENT

INFINITE CONTROL CONFIGURATION

INFINITE

CONTROL

L1

G

GREEN

BROWN

PL1L

H2

H1

DISPLAY LIGHT

INDICATOR LIGHT

2

L

H1

200-240V: BLUE

120V: WH ITE

2

PILOT
LIGH T

BLUE

BROWN

ELEMENT

PILOT

HEATING ELEMENT

L2

H2

L1

L2

EGO
INFINITE
CONTROL

L1

TOGGLE SWITCH CONFIGURATION

GL1L

2

GREEN

BROWN

200-240V: BLUE

120V: WHITE

TOGGLE

SWITCH

PILOT
LIGHT

BLUE

BROWN

ELEMENT

67177 REV-11/2001

7

FDL18-72 WIRING DIAGRAM

REMOTE CONFIGURATION

TWO L AMPHOLDERSONE L AMPHOLDE R

18,24,30 MODELS

36,42,48,54 MODELS

THREE LAMPHOL DERS

60, 66,72 MODELS

FOUR LAMPHOL DERS

84,96 MODELS

ABELS

L

N/L2

ABELS

L

N/L2

N/L2

L1

G

L1

G

L1

200-240V: BLUE

4

5

1

120V: WHITE

200-240V: BLUE

2

3

DISPLAY LIGHT

H1

120V: WHITE

200-24 0: BLUE

BROWN

GREEN

INFINITE

CON TR O L

120V: WHITE

BROWN

GREEN

BROWN

PILOT

1

PL1L2

H1

7

5 4

BRO WN

WHITE

6

INFINITE CONTROL CONFIGURATION

HEATING ELEMENT

INDICATOR LIGHT

L2

H2

EGO
INFINITE

L1

CONTROL

32

6

PILOT

H2

LIGH T

BLAC K

L2

L1

BLUE

7

18,24,30MOD E LS

WHITE

8

BLUE

BLUE

WHITE

6

BLACK

9

BLACK

BLUE

7

ELEMENT

TWO LAMPHOLDERSONE LAMPHOLDER

36,42,48 ,54MODELS

BLUE BLUE

WHITE

BLACK

WHITE

6

BLACK

9 9

ELEMENT

BROWN

BLUE

7

THR E E LAMPHOLDER S

60,66,72 MODELS

WHITE

88

WHITE

BLACK

BLAC K

FOUR LAMPHOLDERS

84,96 MODELS

BLACKWHITE

BLUE

TOGGLE SWITCH CONFIGURATION

ABELS

N/L2

L1

G

120V: WHITE

200 -240V: BLU E

BROWN

GREEN

TOGGLE
SWI TCH

1

7

2 3

5 4

BLUE

6

BROWN

18, 24,30 MODELS

WHITE

8

PILO T
LIGHT

L

BLACK

9

BLUE

BLUE

TWO LAMPHOLDERSONE LAMPH OLDER

36,42,48,54 MODELS

WHITE

BLAC K

8

9

8

BLUE

BROWN

THRE E LAMPH OLDERS

60, 66,72 MODELS

WHITE

BLACK

8

9

ELEMEN T

BLUE

FOUR LA MPHOLDERS

84, 96 MODELS

WHITE

BLACK

LABELS

N/L2

L1

FDD18-72 WIRING DIAGRAM

120V: WHITE

200-240V: BLUE

BROWN

REMOTE CONFIGURATION

ELEMENT

LABELS

N/L2

L1

G

G

N/L2

L1

200-240V: BLUE

120V: WHITE

BROWN
GREEN

200-240V: BLUE

PL1L2
H1

H2

GREEN

120V: WHITE

BROWN

INFINITE CONTROL CONFIGURATION

PL1L2

H1

PILOT
LIGHT

H2

PILOT
LIGHT

BLUE

BLUE

BROWN

ELEMENT

BROWN

ELEMENT

ELEMENT

DISPLAY LIGHT

H1

L2

PILOT

HEATING ELEMENT

INDICATOR LIGHT

H2

EGO
INFINITE

L1

CONTROL

L2

L1

LABELS

TOGGLE SWITCH CONFIGURATION

9

FDDL18-72 WIRING DIAGRAM

LABELS

N/L2

120V: WHITE

200-240: BLUE

BROWN

L1

GREEN

G

LABELS

N/L2

L1

N/L2

L1

G

N/L2

L1

INFINITE
CONTROL

120V: WHITE

200-240: BLUE

120V: WHITE

200-240: BLUE

BROWN
GREEN

120V: WHITE

200-240: BLUE

BROWN

REMOTE CONFIGURATION

BROWN

1 LAMPHOLDER

18,24,30 MDLS

WHITE

BLACK

2 LAMPHOLDERS
36,42,48,54 MDLS

WHITE

BLUE

ELEMENT

BLACK

ELEMENT

3 LAMPHOLDERS

BLUE

60,66,72 MDLS

WHITE

INFINITE CONTROL CONFIGURATION

L1

P

L2

H1

H2

1 LAMPHOLDER

18,24,30 MDLS

PILOT
LIGHT

BLUE

2 LAMPHOLDERS

36,42,48,54 MDLS

ELEMENT

BROWN

3 LAMPHOLDERS

60,66,72 MDLS

3 LAMPHOLDERS

84 MDL

BLACK

4 LAMPHOLDERS

WHITE

BLUE

DISPLAY LIGHT

84,96 MDLS

BLACK

HEATING ELEMENT

INDICATOR LIGHT

L2

L2

INFINITE
CONTROL

L1

P
H1

BROWN

BLUE

WHITE

BLACK

BLUE

WHITE

BLACK

BLUE

WHITE

BLACK

BLUE

WHITE

BLACK

H1

PILOT

L2

H2

PILOT
LIGHT

BLUE

ELEMENT

BROWN

H2

L1

EGO
INFINITE
CONTROL

L1

TOGGLE SWITCH CONFIGURATION

TOGGLE

LABELS

N/L2

120V: WHITE
200-240: BLUE

BROWN

L1

GREEN

G

SWITCH

TOGGLE
SWITCH

BROWN

PILOT
LIGHT

1 LAMPHOLDER

18,24,30 MDLS

WHITE

BLACK

BLUE

PILOT
LIGHT

BLUE

BROWN

2 LAMPHOLDERS
36,42,48,54 MDLS

WHITE

BLUE

BROWN

BLACK

BLUE

ELEMENT

3 LAMPHOLDERS

60,66,72 MDLS

WHITE

BLACK

BLUE

ELEMENT

4 LAMPHOLDERS

84,96 MDL

WHITE

BLACK

67179 REV-7/00

10

8. PARTS LISTS

MODEL “FD” OVERHEAD WARMERS REPLACEMENT PARTS CATALOG

FD Followed by 18, 24, 30, 36, 42, 48, 54, 60, 66, 72, 84, or 96

MODEL VOLTS HIGH WATTAGE LOW WATTAGE

FD18

FD24

FD30

FD36

FD42

FD48

FD54

FD60

FD66

FD72

FD84

FD96

120 400 250
208 400 250
230 368 294
240 400 320
120 575 350
208 575 350
230 529 322
240 575 350
120 760 450
208 760 450
230 698 414
240 760 450
120 920 575
208 920 575
230 845 529
240 920 575
120 1100 675
208 1100 675
230 1011 620
240 1100 675
120 1265 800
208 1265 800
230 1162 735
240 1265 800
120 1425 925
208 1425 925
230 1309 850
240 1425 925
120 1600 1050
208 1610 1050
230 1479 965
240 1610 1050
208 1800 1160
230 1654 1066
240 1800 1160
208 1980 1275
230 1819 1171
240 1980 1275
208 --- 2050
230 --- 1948
240 --- 2050
208 --- 2400
230 --- 2280
240 --- 2400

FOR COMPLETE STYLE AND OPTION DESIGNATION:

ADD ONE SUFFIX FROM EACH FOLLOWING CATEGORY AFTER THE MODEL AND LENGTH

WATTAGE VOLTAGE SWITCH

H=HIGH WATTAGE 1=120V I=INFINITE CONTROL
L=LOW WATTAGE 2=208V T=TOGGLE SWITCH

EXAMPLE:

A WARMER, 48” LONG, HIGH WATTAGE, 208V, WITH INFINITE CONTROL = OH48H2I

3=240V R=REMOTE CONTROL/SWITCH

11

FD18 THRU 96 OVERHEAD WARMERS

ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION

1 76835 HOUSING FD18 75806 ELEMENT FD48 120V 1265W

76836 HOUSING FD24 75807 ELEMENT FD48 208V 1265W
76837 HOUSING FD30 75808 ELEMENT FD48 240V 1265W
76838 HOUSING FD36 75860 ELEMENT FD48 120V 800W
76839 HOUSING FD42 75861 ELEMENT FD48 208V 800W
76840 HOUSING FD48 75862 ELEMENT FD48 240V 800W
76841 HOUSING FD54 75823 ELEMENT FD54 120V 1425W
76842 HOUSING FD60 75824 ELEMENT FD54 208V 1425W
76843 HOUSING FD66 75825 ELEMENT FD54 240V 1425W
76844 HOUSING FD72 75863 ELEMENT FD54 120V 925W
77075 HOUSING FD84 75864 ELEMENT FD54 208V 925W

77076 HOUSING FD96 75865 ELEMENT FD54 240V 925W
2 67005 TOGGLE SWITCH 75817 ELEMENT FD60 120V 1600W
3 76100 SW ITCH GUARD 75809 ELEMENT FD60 208V 1610W
4 55564-EGO INFINITE CONTROL 120V 75810 ELEMENT FD60 240V 1610W

87054-EGO INFINITE CONTROL 208V 75866 ELEMENT FD60 120V 1050W

87053-EGO INFINITE CONTROL 240V 75867 ELEMENT FD60 208V 1050W
5 55825 KNOB 75868 ELEMENT FD60 240V 1050W
6 76805 REFLECTOR FD18 75826 ELEMENT FD66 208V 1800W

76806 REFLECTOR FD24 75827 ELEMENT FD66 240V 1800W
76807 REFLECTOR FD30 75869 ELEMENT FD66 208V 1160W
76808 REFLECTOR FD36 75870 ELEMENT FD66 240V 1160W
76809 REFLECTOR FD42 75811 ELEMENT FD72 208V 1980W
76810 REFLECTOR FD48 75812 ELEMENT FD72 240V 1980W
76811 REFLECTOR FD54 75871 ELEMENT FD72 208V 1275W
76812 REFLECTOR FD60 75872 ELEMENT FD72 240V 1275W
76813 REFLECTOR FD66 75879 ELEMENT FD84 208V 2050W
76814 REFLECTOR FD72 75880 ELEMENT FD84 240V 2050W
77060 REFLECTOR FD84 75881 ELEMENT FD96 208V 2400W
77061 REFLECTOR FD96 75882 ELEMENT FD96 240V 2400W

7 75801 ELEMENT FD18 120V 400W 8 76801 COVER LARGE RH

75833 ELEMENT FD18 208V 400W 9 76802 COVER SMALL
75830 ELEMENT FD18 240V 400W 10 76106 ELEMENT GUARD
75851 ELEMENT FD18 120V 250W 11 76955 MOUNTING BRACKET
75873 ELEMENT FD18 208V 250W 12 67003 ON-OFF PLATE
75874 ELEMENT FD18 240V 320W 13 56530 PILOT LIGHT
75461 ELEMENT FD24 120V 575W 14 WIRE SET: SPECIFY MODEL NO.
75813 ELEMENT FD24 208V 575W 15 76189 INSULATION FD18 THRU FD72
75814 ELEMENT FD24 240V 575W 16 76190 INSULATION FD18
75852 ELEMENT FD24 120V 350W 76191 INSULATION FD24
75875 ELEMENT FD24 208V 350W 76192 INSULATION FD30
75876 ELEMENT FD24 240V 350W 76193 INSULATION FD36
75802 ELEMENT FD30 120V 760W 76194 INSULATION FD42
75820 ELEMENT FD30 208V 760W 76195 INSULATION FD48
75831 ELEMENT FD30 240V 760W 76196 INSULATION FD54
75853 ELEMENT FD30 120V 450W 76197 INSULATION FD60
75877 ELEMENT FD30 208V 450W 76198 INSULATION FD66
75878 ELEMENT FD30 240V 450W 76199 INSULATION FD72
75803 ELEMENT FD36 120V 920W 17 76803 END PLATE
75804 ELEMENT FD36 208V 920W 18 76804 ELEMENT SUPPORT
75805 ELEMENT FD36 240V 920W
75854 ELEMENT FD36 120V 575W
75855 ELEMENT FD36 208V 575W

75856 ELEMENT FD36 240V 575W 58004 SELF RETAINING FASTENER
75819 ELEMENT FD42 120V 1100W 89087 8-32 X 3/16 MACHINE SCREW
75821 ELEMENT FD42 208V 1100W 88993 10-32 X 3/8 NYLOCK MACHINE
75822 ELEMENT FD42 240V 1100W 88909 8-18 X 3/8 SHEET METAL (AB)
75857 ELEMENT FD42 120V 675W 89059 #10 EXTERNAL LOCKW ASHER
75858 ELEMENT FD42 208V 675W 88961 10-24 HEX NUT GREEN-GROUND
75859 ELEMENT FD42 240V 675W

PARTS NOT SHOW N

PARTSNOT SHOWN

12

FD-18 Thru FD-96 EXPLODED VIEW

16

8

7

10

9

6

15

14

18

4

5

11

2

17

12

2

3

1

3

13

67177 REV-11/2001

13

MODEL “FDL” LIGHTED OVERHEAD WARMERS REPLACEMENT PARTS CATALOG

FDL Followed by 18, 24, 30, 36, 42, 48, 54, 60, 66, 72, 84, or 96

MODEL VOLTS HIGH WATTAGE LOW WATTAGE

FDL18 120 480 330

208 462 312
230 441 368
240 480 400

FDL24 120 655 430

208 637 412
230 602 395
240 655 430

FDL30 120 840 530

208 822 512
230 772 487
240 840 530

FDL36 120 1080 735

208 1044 699
230 992 676
240 1080 735

FDL42 120 1260 835

208 1224 799
230 1158 767
240 1260 835

FDL48 120 1425 960

208 1389 924
230 1309 882
240 1425 960

FDL54 120 1585 1085

208 1549 1049
230 1456 997
240 1585 1085

FDL60 120 1840 1290

208 1796 1236
230 1700 1185
240 1850 1290

FDL66 208 1986 1346

230 1874 1286
240 2040 1400

FDL72 208 2166 1461

230 2039 1392
240 2220 1515

FDL84 208 --- 2298

230 --- 2177
240 --- 2370

FDL96 208 --- 2640

230 --- 2498
240 --- 2720

FOR COMPLETE STYLE AND OPTION DESIGNATION:

ADD ONE SUFFIX FROM EACH FOLLOWING CATEGORY AFTER THE MODEL AND LENGTH

WATTAGE VOLTAGE SWITCH

H=HIGH WATTAGE 1=120V I=INFINITE CONTROL
L=LOW WATTAGE 2=208V T=TOGGLE SWITCH

EXAMPLE:

A LIGHTED WARMER, 48” LONG, HIGH WATTAGE, 208V, WITH INFINITE CONTROL = OHL48H2I

3=240V R=REMOTE CONTROL/SWITCH

14

FDL18 THRU 96 LIGHTED OVERHEAD WARMERS

ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION

1 76845 HOUSING FDL18 75824 ELEMENT FD54 208V 1425W

76846 HOUSING FDL24 75825 ELEMENT FD54 240V 1425W
76847 HOUSING FDL30 75863 ELEMENT FD54 120V 925W
76848 HOUSING FDL36 75864 ELEMENT FD54 208V 925W
76849 HOUSING FDL42 75865 ELEMENT FD54 240V 925W
76850 HOUSING FDL48 75817 ELEMENT FD60 120V 1600W
76851 HOUSING FDL54 75809 ELEMENT FD60 208V 1610W
76852 HOUSING FDL60 75810 ELEMENT FD60 240V 1610W
76853 HOUSING FDL66 75866 ELEMENT FD60 120V 1050W
76854 HOUSING FDL72 75867 ELEMENT FD60 208V 1050W
77080 HOUSING FDL84 75868 ELEMENT FD60 240V 1050W

77081 HOUSING FDL96 75826 ELEMENT FD66 208V 1800W
2 67004 TOGGLE SWITCH 75827 ELEMENT FD66 240V 1800W
3 76100 SW ITCH GUARD 75869 ELEMENT FD66 208V 1160W
4 55564-EGO INFINITE CONTROL 120V 75870 ELEMENT FD66 240V 1160W

87054-EGO INFINITE CONTROL 208V 75811 ELEMENT FD72 208V 1980W

87053-EGO INFINITE CONTROL 240V 75812 ELEMENT FD72 240V 1980W
5 55825 KNOB 75871 ELEMENT FD72 208V 1275W
6 76805 REFLECTOR FD18 75872 ELEMENT FD72 240V 1275W

76806 REFLECTOR FD24 75879 ELEMENT FD84 208V 2050W
76807 REFLECTOR FD30 75880 ELEMENT FD84 240V 2050W
76808 REFLECTOR FD36 75881 ELEMENT FD96 208V 2400W
76809 REFLECTOR FD42 75882 ELEMENT FD96 240V 2400W
76810 REFLECTOR FD48 8 76801 COVER LARGE
76811 REFLECTOR FD54 9 76802 COVER SMALL
76812 REFLECTOR FD60 10 76106 ELEMENT GUARD
76813 REFLECTOR FD66 11 76955 MOUNTING BRACKET
76814 REFLECTOR FD72 12 67003 ON-OFF PLATE
77060 REFLECTOR FD84 13 56530 PILOT LIGHT
77061 REFLECTOR FD96 14 WIRE SET: SPECIFY MODEL NO.

7 75801 ELEMENT FD18 120V 400W 15 76159 END COVER RH DL

75833 ELEMENT FD18 208V 400W 16 89182 SNAP-IN BUSHING
75830 ELEMENT FD18 240V 400W 17 76189 INSULATION FD18 THRU FD72
75851 ELEMENT FD18 120V 250W 18 76190 INSULATION FD18
75873 ELEMENT FD18 208V 250W 76191 INSULATION FD24
75874 ELEMENT FD18 240V 320W 76192 INSULATION FD30
75461 ELEMENT FD24 120V 575W 76193 INSULATION FD36
75813 ELEMENT FD24 208V 575W 76194 INSULATION FD42
75814 ELEMENT FD24 240V 575W 76195 INSULATION FD48
75852 ELEMENT FD24 120V 350W 76196 INSULATION FD54
75875 ELEMENT FD24 208V 350W 76197 INSULATION FD60
75876 ELEMENT FD24 240V 350W 76198 INSULATION FD66
75802 ELEMENT FD30 120V 760W 76199 INSULATION FD72
75820 ELEMENT FD30 208V 760W 19 76211 LIGHT SUPPORT DL18
75831 ELEMENT FD30 240V 760W 76212 LIGHT SUPPORT DL24
75853 ELEMENT FD30 120V 450W 76213 LIGHT SUPPORT DL30
75877 ELEMENT FD30 208V 450W 76214 LIGHT SUPPORT DL36
75878 ELEMENT FD30 240V 450W 76215 LIGHT SUPPORT DL42
75803 ELEMENT FD36 120V 920W 76216 LIGHT SUPPORT DL48
75804 ELEMENT FD36 208V 920W 76217 LIGHT SUPPORT DL54
75805 ELEMENT FD36 240V 920W 76218 LIGHT SUPPORT DL60
75854 ELEMENT FD36 120V 575W 76219 LIGHT SUPPORT DL66
75855 ELEMENT FD36 208V 575W 76220 LIGHT SUPPORT DL72
75856 ELEMENT FD36 240V 575W 77015 LIGHT SUPPORT DL84
75819 ELEMENT FD42 120V 1100W 77016 LIGHT SUPPORT DL96
75821 ELEMENT FD42 208V 1100W 20 75917 TW IN LAMPHOLDER
75822 ELEMENT FD42 240V 1100W 21 75916 COATED LIGHT BULB 120V 40W
75857 ELEMENT FD42 120V 675W 76874 COATED LIGHT BULB 240V 40W
75858 ELEMENT FD42 208V 675W 22 76803 END PLATE
75859 ELEMENT FD42 240V 675W 23 76804 ELEMENT SUPPORT
75806 ELEMENT FD48 120V 1265W
75807 ELEMENT FD48 208V 1265W 58004 SELF RETAINING FASTENER
75808 ELEMENT FD48 240V 1265W 89087 8-32 X 3/16 MACHINE SCREW
75860 ELEMENT FD48 120V 800W 88993 10-32 X 3/8 NYLOCK MACHINE
75861 ELEMENT FD48 208V 800W 88909 8-18 X 3/8 SHEET METAL (AB)
75862 ELEMENT FD48 240V 800W 89059 #10 EXTERNAL LOCKWASHER
75823 ELEMENT FD54 120V 1425W 88961 10-24 HEX NUT GREEN-GROUND

PARTS NOT SHOWN

PARTSNOT SHOWN

15

FDL-18 Thru FDL-96 EXPLODED VIEW

9

18

8

10

6

7

14

21

17

19

15

16

4

23

5

20

11

2

O

O

F

N

F

2

3

12

1

22

3

13

67178 REV 11/01

16

MODEL “FDD” or “FDDL” DUAL OVERHEAD WARMERS REPLACEMENT PARTS CATALOG

FDD or FDDL Followed by 18, 24, 30, 36, 42, 48, 54, 60, 66, 72, 84, or 96

HIGH WATTAGE UNITS LOW WATTAGE UNITS

LENGTH FDD SERIES FDDL SERIES FDD SERIES FDDL SERIES

18 120V 800W 120V 880W 120V 500W 120V 580W
18 208V 800W 208V 862W 208V 500W 208V 562W
18 230V 735W 230V 809W 230V 588W 230V 662W
18 240V 800W 240V 880W 240V 640W 240V 720W
24 120V 1150W 120V 1230W 120V 700W 120V 780W
24 208V 1150W 208V 1212W 208V 700W 208V 762W
24 230V 1057W 230V 1130W 230V 643W 230V 717W
24 240V 1150W 240V 1230W 240V 700W 240V 780W
30 120V 1520W 120V 1600W 120V 900W 120V 980W
30 208V 1520W 208V 1582W 208V 900W 208V 962W
30 230V 1396W 230V 1470W 230V 827W 230V 901W
30 240V 1520W 240V 1600W 240V 900W 240V 980W
36 120V 1840W 120V 2000W 120V 1150W 120V 1310W
36 208V 1840W 208V 1964W 208V 1150W 208V 1274W
36 230V 1690W 230V 1837W 230V 1057W 230V 1204W
36 240V 1840W 240V 2000W 240V 1150W 240V 1310W
42 120V 2200W 120V 2360W 120V 1350W 120V 1510W
42 208V 2200W 208V 2324W 208V 1350W 208V 1474W
42 230V 2021W 230V 2168W 230V 1240W 230V 1387W
42 240V 2200W 240V 2360W 240V 1350W 240V 1510W
48 120V 2530W 120V 2690W 120V 1600W 120V 1760W
48 208V 2530W 208V 2654W 208V 1600W 208V 1724W
48 230V 2324W 230V 2471W 230V 1470W 230V 1617W
48 240V 2530W 240V 2690W 240V 1600W 240V 1760W
54 120V 2850W 120V 3010W 120V 1850W 120V 2010W
54 208V 2850W 208V 2974W 208V 1850W 208V 1974W
54 230V 2618W 230V 2765W 230V 1700W 230V 1846W
54 240V 2850W 240V 3010W 240V 1850W 240V 2010W
60 120V 3200W 120V 3440W 120V 2100W 120V 2340W
60 208V 3220W 208V 3406W 208V 2100W 208V 2286W
60 230V 2958W 230V 3178W 230V 1929W 230V 2150W
60 240V 3220W 240V 3460W 240V 2100W 240V 2340W
66 208V 3600W 208V 3786W 208V 2320W 208V 2506W
66 230V 3307W 230V 3527W 230V 2131W 230V 2352W
66 240V 3600W 240V 3840W 240V 2320W 240V 2560W
72 208V 3960W 208V 4146W 208V 2550W 208V 2736W
72 230V 3637W 230V 3858W 230V 2342W 230V 2563W
72 240V 3960W 240V 4200W 240V 2550W 240V 2790W
84 --- --- 208V 4100W 208V 4348W
84 --- --- 230V 3765W 230V 4059W
84 --- --- 240V 4100W 240V 4420W
96 --- --- 208V 4800W 208V 5040W
96 --- --- 230V 4408W 230V 4702W
96 --- --- 240V 4800W 240V 5120W

FOR COMPLETE STYLE AND OPTION DESIGNATION:

ADD ONE SUFFIX FROM EACH FOLLOWING CATEGORY AFTER THE MODEL AND LENGTH

WATTAGE VOLTAGE SWITCH

H=HIGH WATTAGE 1=120V I=INFINITE CONTROL
L=LOW WATTAGE 2=208V T=TOGGLE SWITCH

EXAMPLE:

A LIGHTED DUAL WARMER, 48” LONG, HIGH WATTAGE, 208V, WITH TOGGLE SWITCH = OHDL46H2T

3=240V R=REMOTE CONTROL/SWITCH

17

FDD or FDDL18 THRU 96 DUAL OVERHEAD WARMERS

ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION

1 76855 HOUSING FDD/FDDL18 75863 ELEMENT FD54 120V 925W

2 67004 TOGGLE SWITCH 75870 ELEMENT FD66 240V 1160W
3 76100 SW ITCH GUARD 75811 ELEMENT FD72 208V 1980W
4 55564-

5 55825 KNOB 75879 ELEMENT FD84 208V 2050W
6 76985 REFLECTOR FD18 DIRECTED 75880 ELEMENT FD84 240V 2050W

7 75801 ELEMENT FD18 120V 400W 17 76189 INSULATION FD18 THRU FD72

76856 HOUSING FDD/FDDL24 75864 ELEMENT FD54 208V 925W
76857 HOUSING FDD/FDDL30 75865 ELEMENT FD54 240V 925W
76858 HOUSING FDD/FDDL36 75817 ELEMENT FD60 120V 1600W
76859 HOUSING FDD/FDDL42 75809 ELEMENT FD60 208V 1610W
76860 HOUSING FDD/FDDL48 75810 ELEMENT FD60 240V 1610W
76861 HOUSING FDD/FDDL54 75866 ELEMENT FD60 120V 1050W
76862 HOUSING FDD/FDDL60 75867 ELEMENT FD60 208V 1050W
76863 HOUSING FDD/FDDL66 75868 ELEMENT FD60 240V 1050W
76864 HOUSING FDD/FDDL72 75826 ELEMENT FD66 208V 1800W
77085 HOUSING FDD/FDDL84 75827 ELEMENT FD66 240V 1800W
77086 HOUSING FDD/FDDL96 75869 ELEMENT FD66 208V 1160W

EGO

87054-

EGO

87053-

EGO

76986 REFLECTOR FD24 DIRECTED 75881 ELEMENT FD96 208V 2400W
76987 REFLECTOR FD30 DIRECTED 75882 ELEMENT FD96 240V 2400W
76988 REFLECTOR FD36 DIRECTED 8 77151 COVER LARGE RH
76989 REFLECTOR FD42 DIRECTED 9 77155 COVER SMALL RH
76990 REFLECTOR FD48 DIRECTED 10 77157 ELEMENT GUARD
76991 REFLECTOR FD54 DIRECTED 11 76955 MOUNTING BRACKET
76992 REFLECTOR FD60 DIRECTED 12 67003 ON-OFF PLATE
76993 REFLECTOR FD66 DIRECTED 13 56530 PILOT LIGHT
76994 REFLECTOR FD72 DIRECTED 14 WIRE SET: SPECIFY MODEL NO.
76995 REFLECTOR FD84 DIRECTED 15 76159 END COVER RH DL
76996 REFLECTOR FD96 DIRECTED 16 89182 SNAP-IN BUSHING

75833 ELEMENT FD18 208V 400W 18 76190 INSULATION FD18
75830 ELEMENT FD18 240V 400W 76191 INSULATION FD24
75851 ELEMENT FD18 120V 250W 76192 INSULATION FD30
75873 ELEMENT FD18 208V 250W 76193 INSULATION FD36
75874 ELEMENT FD18 240V 320W 76194 INSULATION FD42
75461 ELEMENT FD24 120V 575W 76195 INSULATION FD48
75813 ELEMENT FD24 208V 575W 76196 INSULATION FD54
75814 ELEMENT FD24 240V 575W 76197 INSULATION FD60
75852 ELEMENT FD24 120V 350W 76198 INSULATION FD66
75875 ELEMENT FD24 208V 350W 76199 INSULATION FD72
75876 ELEMENT FD24 240V 350W 19 76211 LIGHT SUPPORT DL18
75802 ELEMENT FD30 120V 760W 76212 LIGHT SUPPORT DL24
75820 ELEMENT FD30 208V 760W 76213 LIGHT SUPPORT DL30
75831 ELEMENT FD30 240V 760W 76214 LIGHT SUPPORT DL36
75853 ELEMENT FD30 120V 450W 76215 LIGHT SUPPORT DL42
75877 ELEMENT FD30 208V 450W 76216 LIGHT SUPPORT DL48
75878 ELEMENT FD30 240V 450W 76217 LIGHT SUPPORT DL54
75803 ELEMENT FD36 120V 920W 76218 LIGHT SUPPORT DL60
75804 ELEMENT FD36 208V 920W 76219 LIGHT SUPPORT DL66
75805 ELEMENT FD36 240V 920W 76220 LIGHT SUPPORT DL72
75854 ELEMENT FD36 120V 575W 77015 LIGHT SUPPORT DL84
75855 ELEMENT FD36 208V 575W 77016 LIGHT SUPPORT DL96
75856 ELEMENT FD36 240V 575W 20 75917 TW IN LAMPHOLDER
75819 ELEMENT FD42 120V 1100W 21 75916 COATED LIGHT BULB 120V 40W
75821 ELEMENT FD42 208V 1100W 76874 COATED LIGHT BULB 240V 40W
75822 ELEMENT FD42 240V 1100W 22 77152 COVER LARGE LH
75857 ELEMENT FD42 120V 675W 23 76803 END PLATE
75858 ELEMENT FD42 208V 675W 24 77158 ELEMENT SUPPORT
75859 ELEMENT FD42 240V 675W 25 77156 COVER SMALL LH
75806 ELEMENT FD48 120V 1265W
75807 ELEMENT FD48 208V 1265W 58004 SELF RETAINING FASTENER
75808 ELEMENT FD48 240V 1265W 89087 8-32 X 3/16 MACHINE SCREW
75860 ELEMENT FD48 120V 800W 88993 10-32 X 3/8 NYLOCK MACHINE
75861 ELEMENT FD48 208V 800W 88909 8-18 X 3/8 SHEET METAL (AB)
75862 ELEMENT FD48 240V 800W 89059 #10 EXTERNAL LOCKW ASHER
75823 ELEMENT FD54 120V 1425W 88961 10-24 HEX NUT GREEN-GROUND
75824 ELEMENT FD54 208V 1425W 46877 1/8-27 X 3/4 NIPPLE
75825 ELEMENT FD54 240V 1425W 46876 1/8-27 NUT

INFINITE CONTROL 120V 75812 ELEMENT FD72 240V 1980W
INFINITE CONTROL 208V 75871 ELEMENT FD72 208V 1275W
INFINITE CONTROL 240V 75872 ELEMENT FD72 240V 1275W

PARTS NOT SHOWN

PARTSNOT SHOWN

18

FDD or FDDL-18 Thru -96 EXPLODED VIEW

25

22

7

8

10

9

19

6

18

15

20

2

12

21

1

14

11

23

17

24

16

4

5

3

13

FDDL-REV112001.dft

19

9. APW WYOTT EQUIPMENT LIMITED WARRANTY

APW Wyott Foodservice Equipment Company warrants it's equipment against defects in materials and workmanship, subject to the
following conditions:

This warranty applies to the original owner only and is not assignable.
Should any product fail to function in its intended manner under normal use within the limits defined in this warranty,at the option of

APW Wyott such product will be repaired or replaced by APW Wyott or its Authorized Service Agency.APW Wyott will only be
responsible for charges incurred or service performed by its Authorized Service Agencies. The use of other than APW Wyott
Authorized Service Agencies will void this warranty and APW Wyott will not be responsible for such work or any charges associated
with same.The closest APWWyottAuthorized Service Agent must be used.

This warranty covers products shipped into the 48 contiguous United States, Hawaii, metropolitan areas of Alaska and Canada. There
will be no labor coverage forequipment located on any island not connected byroadway to the mainland.

Warranty coverage on products used outside the 48 contiguous United States, Hawaii, and metropolitan areas of Alaska and Canada
may vary. Contact the international APWWyott distributor,dealer, or service agency for details.

TimePeriod

One year for parts and one year for labor, effective from the date of purchase by the original owner.The Authorized Service Agency
may, at their option, require proof of purchase. Parts replaced under this warranty are warranted for the un-expired portion of the
original product warranty only.

Exceptions

Inall cases, parts covered byextended warranty will be shipped FOB the factory after the first year.

Portable Carry In Products

Equipment weighing over 70 pounds or permanently installed will be serviced on-site as per the terms of this warranty. Equipment
weighing 70 pounds or under, and which is not permanently installed, i.e. with cord and plug, is considered portable and is subject to
the following warranty handling limitations. If portable equipment fails to operate in its intended manner on the first day of
connection, or use, atAPW Wyott'soption or itsAuthorized ServiceAgency,it will be serviced on site or replaced.

From day two through the conclusion of this warranty period, portable units must be taken to or sent prepaid to the APW Wyott
Authorized ServiceAgency for in-warranty repairs.No mileage or travel charges are allowed onportable units after the first day of use.
If the customer wants on-site service, they may receive same by paying the travel and mileage charges. Exceptions to this rule: (1)
countertop warmers and cookers,which arecovered underthe Enhanced Warranty Program, and (2) toastersor rollergrills whichhave
instore service.

Exclusions

The following conditions are not covered bywarranty:

If the equipment has been changed, altered, modified or repaired by other than an Authorized Service Agency during or after the
warranty period, then the manufacturer shall not be liable for any damages to any person orto any property,which may resultfrom the
use of the equipment thereafter.

This warranty does not cover services performed at overtime or premium labor rates. Should service be required at times which
normally involve overtime or premium labor rates,the owner shall be charged for the difference between normalservice rates andsuch
premium rates.APW Wyottdoes not assume any liability for extended delays inreplacing or repairing any items beyond its control.

Inall cases, the use of other than APWWyottAuthorized OEM Replacement Partswill void this warranty.
This equipment is intended for commercial use only.Warrantyis void if equipment is installed in other than commercial application.

WaterQuality Requirements

Water supply intended for a unit that has in excess of 3.0 grains of hardness per gallon (GPG) must be treated or softened before
being used. Water containing over 3.0 GPG will decrease the efficiency and reduce the operation life of the unit.

Note: Product failure caused by liming or sediment buildup is not covered under warranty.
THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED

INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSES
AND CONSTITUTES THE ENTIRE LIABILITY OFAPW WYOTT. IN NO EVENT DOES THE LIMITED WARRANTY
EXTEND BEYOND THE TERMS STATED HEREIN.

*Gas/Electric Cookline:

component parts, except switches and thermostats. (2additional years on parts only.No labor on second or third year.)

*BroilerBriquettes,
*Heat Strips:
*GlassWindows, Doors, Seals,Rubber Seals, Light Bulbs:

*Equipment failure relating to improper installation, improper utility connection or supply and problems due to
ventilation.
*Equipment that has not been properly maintained, calibration of controls, adjustments, damage from improper cleaning
and water damageto controls.
*Equipment that has not been used in an appropriate manner, or has been subject to misuse or misapplication, neglect,
abuse, accident, alteration, negligence, damage duringtransit, delivery or installation, fire,flood, riot or act of god.
*Equipment that has the model number or serial number removed or altered.

Models FD, FDL, FDD, FDDL. Two(2) YearWarranty on element only. No labor second year.

Models GCB, GCRB, GF, GGM, GGT, CHP-H, EF, EG, EHP. Three (3) Year Warranty on all

RockGrates, Cooking Grates, Burner Shields,Fireboxes:

90Day Material Only. No Labor.

90Day Material Only.No Labor.

9/05

20